Winfast USB II (card=7)
[   85.544651][ T1338] em28xx 7-1:0.132: analog set to bulk mode.
[   85.547248][   T60] em28xx 7-1:0.132: Registering V4L2 extension
[   85.556196][ T1338] usb 7-1: USB disconnect, device number 24
[   85.559065][ T1338] em28xx 7-1:0.132: Disconnecting em28xx
[   85.594445][   T10] em28xx 6-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   85.597169][   T10] em28xx 6-1:0.132: board has no eeprom
[   85.619713][   T60] em28xx 7-1:0.132: Config register raw data: 0xffffffed
[   85.622748][   T60] em28xx 7-1:0.132: AC97 chip type couldn't be determined
[   85.625198][   T60] em28xx 7-1:0.132: No AC97 audio processor
[   85.627852][   T60] usb 7-1: Decoder not found
[   85.629281][   T60] em28xx 7-1:0.132: failed to create media graph
[   85.631601][   T60] em28xx 7-1:0.132: V4L2 device video103 deregistered
[   85.636929][   T60] em28xx 7-1:0.132: Remote control support is not available for this card.
[   85.640828][ T1338] em28xx 7-1:0.132: Closing input extension
[   85.646694][ T1338] em28xx 7-1:0.132: Freeing device
[   85.651910][   T10] em28xx 6-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   85.654371][   T10] em28xx 6-1:0.132: analog set to bulk mode.
[   85.657723][ T6055] em28xx 6-1:0.132: Registering V4L2 extension
[   85.668193][   T10] usb 6-1: USB disconnect, device number 20
[   85.671307][   T10] em28xx 6-1:0.132: Disconnecting em28xx
[   85.683248][ T6166] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[   85.738861][ T6055] em28xx 6-1:0.132: Config register raw data: 0xffffffed
[   85.741664][ T6055] em28xx 6-1:0.132: AC97 chip type couldn't be determined
[   85.744297][ T6055] em28xx 6-1:0.132: No AC97 audio processor
[   85.744702][ T6166] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   85.747023][ T6055] usb 6-1: Decoder not found
[   85.749733][ T6166] em28xx 5-1:0.132: board has no eeprom
[   85.751141][ T6055] em28xx 6-1:0.132: failed to create media graph
[   85.755249][ T6055] em28xx 6-1:0.132: V4L2 device video103 deregistered
[   85.759057][ T6055] em28xx 6-1:0.132: Remote control support is not available for this card.
[   85.763095][   T10] em28xx 6-1:0.132: Closing input extension
[   85.768564][   T10] em28xx 6-1:0.132: Freeing device
[   85.811893][ T6166] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   85.815087][ T6166] em28xx 5-1:0.132: analog set to bulk mode.
[   85.818733][ T1338] em28xx 5-1:0.132: Registering V4L2 extension
[   85.824655][ T6166] usb 5-1: USB disconnect, device number 21
[   85.827868][ T6166] em28xx 5-1:0.132: Disconnecting em28xx
[   85.842910][ T6210] usb 8-1: new high-speed USB device number 21 using dummy_hcd
[   85.898175][ T1338] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[   85.900405][ T1338] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[   85.903849][ T1338] em28xx 5-1:0.132: No AC97 audio processor
[   85.906629][ T1338] usb 5-1: Decoder not found
[   85.908096][ T1338] em28xx 5-1:0.132: failed to create media graph
[   85.910084][ T1338] em28xx 5-1:0.132: V4L2 device video103 deregistered
[   85.914281][ T1338] em28xx 5-1:0.132: Remote control support is not available for this card.
[   85.916949][ T6166] em28xx 5-1:0.132: Closing input extension
[   85.920479][ T6166] em28xx 5-1:0.132: Freeing device
[   86.001956][ T6210] usb 8-1: Using ep0 maxpacket: 32
[   86.004822][ T6210] usb 8-1: config 0 has an invalid interface number: 132 but max is 0
[   86.007421][ T6210] usb 8-1: config 0 has no interface number 0
[   86.009308][ T6210] usb 8-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   86.014572][ T6210] usb 8-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   86.017316][ T6210] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   86.019772][ T6210] usb 8-1: Product: syz
[   86.021033][ T6210] usb 8-1: Manufacturer: syz
[   86.022617][ T6210] usb 8-1: SerialNumber: syz
[   86.025605][ T6210] usb 8-1: config 0 descriptor??
[   86.027612][ T6679] raw-gadget.0 gadget.3: fail, usb_ep_enable returned -22
[   86.031709][ T6210] em28xx 8-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   86.035472][ T6210] em28xx 8-1:0.132: Video interface 132 found: bulk
[   86.111897][   T60] usb 7-1: new high-speed USB device number 25 using dummy_hcd
[   86.221930][   T54] usb 6-1: new high-speed USB device number 21 using dummy_hcd
[   86.261938][   T60] usb 7-1: Using ep0 maxpacket: 32
[   86.264730][   T60] usb 7-1: config 0 has an invalid interface number: 132 but max is 0
[   86.267384][   T60] usb 7-1: config 0 has no interface number 0
[   86.269401][   T60] usb 7-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   86.274236][   T60] usb 7-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   86.277065][   T60] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   86.279659][   T60] usb 7-1: Product: syz
[   86.281028][   T60] usb 7-1: Manufacturer: syz
[   86.283158][   T60] usb 7-1: SerialNumber: syz
[   86.286065][   T60] usb 7-1: config 0 descriptor??
[   86.288207][ T6689] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[   86.292240][ T6210] em28xx 8-1:0.132: unknown em28xx chip ID (0)
[   86.293275][   T60] em28xx 7-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   86.297096][   T60] em28xx 7-1:0.132: Video interface 132 found: bulk
[   86.355743][ T6210] em28xx 8-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   86.359288][ T6210] em28xx 8-1:0.132: board has no eeprom
[   86.371876][   T54] usb 6-1: Using ep0 maxpacket: 32
[   86.374219][   T34] usb 5-1: new high-speed USB device number 22 using dummy_hcd
[   86.380310][   T54] usb 6-1: config 0 has an invalid interface number: 132 but max is 0
[   86.383887][   T54] usb 6-1: config 0 has no interface number 0
[   86.386507][   T54] usb 6-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   86.392725][   T54] usb 6-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   86.396441][   T54] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   86.399788][   T54] usb 6-1: Product: syz
[   86.401617][   T54] usb 6-1: Manufacturer: syz
[   86.403702][   T54] usb 6-1: SerialNumber: syz
[   86.408021][   T54] usb 6-1: config 0 descriptor??
[   86.410792][ T6693] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[   86.415825][   T54] em28xx 6-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   86.419835][   T54] em28xx 6-1:0.132: Video interface 132 found: bulk
[   86.422012][ T6210] em28xx 8-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   86.425900][ T6210] em28xx 8-1:0.132: analog set to bulk mode.
[   86.429007][   T10] em28xx 8-1:0.132: Registering V4L2 extension
[   86.434074][ T6210] usb 8-1: USB disconnect, device number 21
[   86.437368][ T6210] em28xx 8-1:0.132: Disconnecting em28xx
[   86.503470][   T10] em28xx 8-1:0.132: Config register raw data: 0xffffffed
[   86.505623][   T10] em28xx 8-1:0.132: AC97 chip type couldn't be determined
[   86.507820][   T10] em28xx 8-1:0.132: No AC97 audio processor
[   86.510522][   T10] usb 8-1: Decoder not found
[   86.513795][   T10] em28xx 8-1:0.132: failed to create media graph
[   86.515777][   T10] em28xx 8-1:0.132: V4L2 device video103 deregistered
[   86.518997][   T10] em28xx 8-1:0.132: Remote control support is not available for this card.
[   86.521663][ T6210] em28xx 8-1:0.132: Closing input extension
[   86.525035][ T6210] em28xx 8-1:0.132: Freeing device
[   86.532461][   T34] usb 5-1: Using ep0 maxpacket: 32
[   86.535507][   T34] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[   86.538048][   T34] usb 5-1: config 0 has no interface number 0
[   86.540072][   T34] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   86.545008][   T34] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   86.547921][   T34] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   86.550536][   T34] usb 5-1: Product: syz
[   86.551965][   T34] usb 5-1: Manufacturer: syz
[   86.553522][   T34] usb 5-1: SerialNumber: syz
[   86.555442][   T60] em28xx 7-1:0.132: unknown em28xx chip ID (0)
[   86.556910][   T34] usb 5-1: config 0 descriptor??
[   86.560510][ T6695] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[   86.565149][   T34] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   86.568691][   T34] em28xx 5-1:0.132: Video interface 132 found: bulk
[   86.615922][   T60] em28xx 7-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   86.618771][   T60] em28xx 7-1:0.132: board has no eeprom
[   86.671841][   T60] em28xx 7-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   86.674443][   T60] em28xx 7-1:0.132: analog set to bulk mode.
[   86.676995][ T6166] em28xx 7-1:0.132: Registering V4L2 extension
[   86.683047][   T54] em28xx 6-1:0.132: unknown em28xx chip ID (0)
[   86.685906][   T60] usb 7-1: USB disconnect, device number 25
[   86.689565][   T60] em28xx 7-1:0.132: Disconnecting em28xx
[   86.740122][ T6166] em28xx 7-1:0.132: Config register raw data: 0xffffffed
[   86.748054][ T6166] em28xx 7-1:0.132: AC97 chip type couldn't be determined
[   86.751288][ T6166] em28xx 7-1:0.132: No AC97 audio processor
[   86.755423][   T54] em28xx 6-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   86.756275][ T6166] usb 7-1: Decoder not found
[   86.758213][   T54] em28xx 6-1:0.132: board has no eeprom
[   86.759690][ T6166] em28xx 7-1:0.132: failed to create media graph
[   86.759707][ T6166] em28xx 7-1:0.132: V4L2 device video103 deregistered
[   86.760665][ T6166] em28xx 7-1:0.132: Remote control support is not available for this card.
[   86.769785][   T60] em28xx 7-1:0.132: Closing input extension
[   86.775255][   T60] em28xx 7-1:0.132: Freeing device
[   86.821992][   T54] em28xx 6-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   86.824824][   T54] em28xx 6-1:0.132: analog set to bulk mode.
[   86.826808][   T34] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[   86.829231][ T6207] em28xx 6-1:0.132: Registering V4L2 extension
[   86.833179][   T54] usb 6-1: USB disconnect, device number 21
[   86.835626][   T54] em28xx 6-1:0.132: Disconnecting em28xx
[   86.886659][ T6207] em28xx 6-1:0.132: Config register raw data: 0xffffffed
[   86.891024][ T6207] em28xx 6-1:0.132: AC97 chip type couldn't be determined
[   86.895601][ T6207] em28xx 6-1:0.132: No AC97 audio processor
[   86.899240][   T34] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   86.904205][   T34] em28xx 5-1:0.132: board has no eeprom
[   86.906810][ T6207] usb 6-1: Decoder not found
[   86.908781][ T6207] em28xx 6-1:0.132: failed to create media graph
[   86.911249][ T6207] em28xx 6-1:0.132: V4L2 device video103 deregistered
[   86.915501][ T6207] em28xx 6-1:0.132: Remote control support is not available for this card.
[   86.918245][   T54] em28xx 6-1:0.132: Closing input extension
[   86.922544][   T54] em28xx 6-1:0.132: Freeing device
[   86.972010][   T34] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   86.974479][   T34] em28xx 5-1:0.132: analog set to bulk mode.
[   86.976710][ T6430] em28xx 5-1:0.132: Registering V4L2 extension
[   86.985752][   T34] usb 5-1: USB disconnect, device number 22
[   86.988938][   T34] em28xx 5-1:0.132: Disconnecting em28xx
[   86.994619][ T6082] usb 8-1: new high-speed USB device number 22 using dummy_hcd
[   87.049289][ T6430] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[   87.052626][ T6430] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[   87.054823][ T6430] em28xx 5-1:0.132: No AC97 audio processor
[   87.057533][ T6430] usb 5-1: Decoder not found
[   87.059465][ T6430] em28xx 5-1:0.132: failed to create media graph
[   87.061645][ T6430] em28xx 5-1:0.132: V4L2 device video103 deregistered
[   87.065097][ T6430] em28xx 5-1:0.132: Remote control support is not available for this card.
[   87.068241][   T34] em28xx 5-1:0.132: Closing input extension
[   87.072117][   T34] em28xx 5-1:0.132: Freeing device
[   87.152628][ T6082] usb 8-1: Using ep0 maxpacket: 32
[   87.155754][ T6082] usb 8-1: config 0 has an invalid interface number: 132 but max is 0
[   87.158533][ T6082] usb 8-1: config 0 has no interface number 0
[   87.160742][ T6082] usb 8-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   87.168419][ T6082] usb 8-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   87.171563][ T6082] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   87.174185][ T6082] usb 8-1: Product: syz
[   87.175467][ T6082] usb 8-1: Manufacturer: syz
[   87.176905][ T6082] usb 8-1: SerialNumber: syz
[   87.180056][ T6082] usb 8-1: config 0 descriptor??
[   87.182137][ T6704] raw-gadget.0 gadget.3: fail, usb_ep_enable returned -22
[   87.187656][ T6082] em28xx 8-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   87.192392][ T6082] em28xx 8-1:0.132: Video interface 132 found: bulk
[   87.242012][ T6210] usb 7-1: new high-speed USB device number 26 using dummy_hcd
[   87.371885][   T54] usb 6-1: new high-speed USB device number 22 using dummy_hcd
[   87.391911][ T6210] usb 7-1: Using ep0 maxpacket: 32
[   87.394788][ T6210] usb 7-1: config 0 has an invalid interface number: 132 but max is 0
[   87.397623][ T6210] usb 7-1: config 0 has no interface number 0
[   87.399737][ T6210] usb 7-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   87.405885][ T6210] usb 7-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   87.408725][ T6210] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   87.411260][ T6210] usb 7-1: Product: syz
[   87.412921][ T6210] usb 7-1: Manufacturer: syz
[   87.414419][ T6210] usb 7-1: SerialNumber: syz
[   87.417208][ T6210] usb 7-1: config 0 descriptor??
[   87.419952][ T6712] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[   87.424756][ T6210] em28xx 7-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   87.427813][ T6210] em28xx 7-1:0.132: Video interface 132 found: bulk
[   87.442408][ T6082] em28xx 8-1:0.132: unknown em28xx chip ID (0)
[   87.505523][ T6082] em28xx 8-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   87.509166][ T6082] em28xx 8-1:0.132: board has no eeprom
[   87.521830][   T54] usb 6-1: Using ep0 maxpacket: 32
[   87.523522][   T34] usb 5-1: new high-speed USB device number 23 using dummy_hcd
[   87.527219][   T54] usb 6-1: config 0 has an invalid interface number: 132 but max is 0
[   87.530083][   T54] usb 6-1: config 0 has no interface number 0
[   87.532288][   T54] usb 6-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   87.536894][   T54] usb 6-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   87.539768][   T54] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   87.542346][   T54] usb 6-1: Product: syz
[   87.543663][   T54] usb 6-1: Manufacturer: syz
[   87.545170][   T54] usb 6-1: SerialNumber: syz
[   87.547966][   T54] usb 6-1: config 0 descriptor??
[   87.550567][ T6717] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[   87.556310][   T54] em28xx 6-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   87.559958][   T54] em28xx 6-1:0.132: Video interface 132 found: bulk
[   87.562266][ T6082] em28xx 8-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   87.564737][ T6082] em28xx 8-1:0.132: analog set to bulk mode.
[   87.567256][ T6207] em28xx 8-1:0.132: Registering V4L2 extension
[   87.573854][ T6082] usb 8-1: USB disconnect, device number 22
[   87.577511][ T6082] em28xx 8-1:0.132: Disconnecting em28xx
[   87.640256][ T6207] em28xx 8-1:0.132: Config register raw data: 0xffffffed
[   87.642820][ T6207] em28xx 8-1:0.132: AC97 chip type couldn't be determined
[   87.645038][ T6207] em28xx 8-1:0.132: No AC97 audio processor
[   87.648676][ T6207] usb 8-1: Decoder not found
[   87.650526][ T6207] em28xx 8-1:0.132: failed to create media graph
[   87.653220][ T6207] em28xx 8-1:0.132: V4L2 device video103 deregistered
[   87.657665][ T6207] em28xx 8-1:0.132: Remote control support is not available for this card.
[   87.661380][ T6082] em28xx 8-1:0.132: Closing input extension
[   87.671922][   T34] usb 5-1: Using ep0 maxpacket: 32
[   87.674821][ T6082] em28xx 8-1:0.132: Freeing device
[   87.678799][   T34] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[   87.681185][   T34] usb 5-1: config 0 has no interface number 0
[   87.685464][   T34] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   87.692635][   T34] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   87.693388][ T6210] em28xx 7-1:0.132: unknown em28xx chip ID (0)
[   87.695503][   T34] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   87.699984][   T34] usb 5-1: Product: syz
[   87.701331][   T34] usb 5-1: Manufacturer: syz
[   87.703100][   T34] usb 5-1: SerialNumber: syz
[   87.706513][   T34] usb 5-1: config 0 descriptor??
[   87.709337][ T6719] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[   87.714799][   T34] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   87.717786][   T34] em28xx 5-1:0.132: Video interface 132 found: bulk
[   87.753461][ T6210] em28xx 7-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   87.757211][ T6210] em28xx 7-1:0.132: board has no eeprom
[   87.812118][   T54] em28xx 6-1:0.132: unknown em28xx chip ID (0)
[   87.813754][ T6210] em28xx 7-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   87.817019][ T6210] em28xx 7-1:0.132: analog set to bulk mode.
[   87.819188][   T10] em28xx 7-1:0.132: Registering V4L2 extension
[   87.822352][ T6210] usb 7-1: USB disconnect, device number 26
[   87.824675][ T6210] em28xx 7-1:0.132: Disconnecting em28xx
[   87.874070][   T54] em28xx 6-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   87.876861][   T54] em28xx 6-1:0.132: board has no eeprom
[   87.886357][   T10] em28xx 7-1:0.132: Config register raw data: 0xffffffed
[   87.888716][   T10] em28xx 7-1:0.132: AC97 chip type couldn't be determined
[   87.891243][   T10] em28xx 7-1:0.132: No AC97 audio processor
[   87.894977][   T10] usb 7-1: Decoder not found
[   87.896864][   T10] em28xx 7-1:0.132: failed to create media graph
[   87.899583][   T10] em28xx 7-1:0.132: V4L2 device video103 deregistered
[   87.904014][   T10] em28xx 7-1:0.132: Remote control support is not available for this card.
[   87.907615][ T6210] em28xx 7-1:0.132: Closing input extension
[   87.914037][ T6210] em28xx 7-1:0.132: Freeing device
[   87.932700][   T54] em28xx 6-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   87.935253][   T54] em28xx 6-1:0.132: analog set to bulk mode.
[   87.938618][ T6430] em28xx 6-1:0.132: Registering V4L2 extension
[   87.941027][   T54] usb 6-1: USB disconnect, device number 22
[   87.944593][   T54] em28xx 6-1:0.132: Disconnecting em28xx
[   87.972204][   T34] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[   88.010102][ T6430] em28xx 6-1:0.132: Config register raw data: 0xffffffed
[   88.018246][ T6430] em28xx 6-1:0.132: AC97 chip type couldn't be determined
[   88.021228][ T6430] em28xx 6-1:0.132: No AC97 audio processor
[   88.024445][ T6430] usb 6-1: Decoder not found
[   88.025913][ T6430] em28xx 6-1:0.132: failed to create media graph
[   88.028444][ T6430] em28xx 6-1:0.132: V4L2 device video103 deregistered
[   88.031227][ T6430] em28xx 6-1:0.132: Remote control support is not available for this card.
[   88.035466][   T54] em28xx 6-1:0.132: Closing input extension
[   88.039174][   T34] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   88.045002][   T54] em28xx 6-1:0.132: Freeing device
[   88.048285][   T34] em28xx 5-1:0.132: board has no eeprom
[   88.101908][   T34] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   88.104468][   T34] em28xx 5-1:0.132: analog set to bulk mode.
[   88.106399][ T6430] em28xx 5-1:0.132: Registering V4L2 extension
[   88.111662][   T34] usb 5-1: USB disconnect, device number 23
[   88.115968][   T34] em28xx 5-1:0.132: Disconnecting em28xx
[   88.131852][ T6082] usb 8-1: new high-speed USB device number 23 using dummy_hcd
[   88.175954][ T6430] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[   88.178251][ T6430] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[   88.180571][ T6430] em28xx 5-1:0.132: No AC97 audio processor
[   88.184640][ T6430] usb 5-1: Decoder not found
[   88.186156][ T6430] em28xx 5-1:0.132: failed to create media graph
[   88.188142][ T6430] em28xx 5-1:0.132: V4L2 device video103 deregistered
[   88.191582][ T6430] em28xx 5-1:0.132: Remote control support is not available for this card.
[   88.194945][   T34] em28xx 5-1:0.132: Closing input extension
[   88.199676][   T34] em28xx 5-1:0.132: Freeing device
[   88.281914][ T6082] usb 8-1: Using ep0 maxpacket: 32
[   88.284750][ T6082] usb 8-1: config 0 has an invalid interface number: 132 but max is 0
[   88.287234][ T6082] usb 8-1: config 0 has no interface number 0
[   88.289099][ T6082] usb 8-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   88.293801][ T6082] usb 8-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   88.296601][ T6082] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   88.299028][ T6082] usb 8-1: Product: syz
[   88.300449][ T6082] usb 8-1: Manufacturer: syz
[   88.301990][ T6082] usb 8-1: SerialNumber: syz
[   88.304784][ T6082] usb 8-1: config 0 descriptor??
[   88.306790][ T6728] raw-gadget.0 gadget.3: fail, usb_ep_enable returned -22
[   88.310520][ T6082] em28xx 8-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   88.314427][ T6082] em28xx 8-1:0.132: Video interface 132 found: bulk
[   88.382030][ T6166] usb 7-1: new high-speed USB device number 27 using dummy_hcd
2025/09/21 14:16:25 executed programs: 100
[   88.501990][   T61] usb 6-1: new high-speed USB device number 23 using dummy_hcd
[   88.562029][ T6166] usb 7-1: Using ep0 maxpacket: 32
[   88.564911][ T6166] usb 7-1: config 0 has an invalid interface number: 132 but max is 0
[   88.567756][ T6166] usb 7-1: config 0 has no interface number 0
[   88.570166][ T6166] usb 7-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   88.572290][ T6082] em28xx 8-1:0.132: unknown em28xx chip ID (0)
[   88.575939][ T6166] usb 7-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   88.578998][ T6166] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   88.581532][ T6166] usb 7-1: Product: syz
[   88.582952][ T6166] usb 7-1: Manufacturer: syz
[   88.584403][ T6166] usb 7-1: SerialNumber: syz
[   88.587017][ T6166] usb 7-1: config 0 descriptor??
[   88.589095][ T6737] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[   88.593343][ T6166] em28xx 7-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   88.596525][ T6166] em28xx 7-1:0.132: Video interface 132 found: bulk
[   88.633680][ T6082] em28xx 8-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   88.636442][ T6082] em28xx 8-1:0.132: board has no eeprom
[   88.651844][   T61] usb 6-1: Using ep0 maxpacket: 32
[   88.655263][   T61] usb 6-1: config 0 has an invalid interface number: 132 but max is 0
[   88.658110][   T61] usb 6-1: config 0 has no interface number 0
[   88.660256][   T61] usb 6-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   88.661847][   T34] usb 5-1: new high-speed USB device number 24 using dummy_hcd
[   88.665504][   T61] usb 6-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   88.668611][   T61] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   88.671712][   T61] usb 6-1: Product: syz
[   88.673532][   T61] usb 6-1: Manufacturer: syz
[   88.675474][   T61] usb 6-1: SerialNumber: syz
[   88.679900][   T61] usb 6-1: config 0 descriptor??
[   88.682278][ T6741] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[   88.687769][   T61] em28xx 6-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   88.691853][   T61] em28xx 6-1:0.132: Video interface 132 found: bulk
[   88.692035][ T6082] em28xx 8-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   88.697025][ T6082] em28xx 8-1:0.132: analog set to bulk mode.
[   88.699376][   T54] em28xx 8-1:0.132: Registering V4L2 extension
[   88.702699][ T6082] usb 8-1: USB disconnect, device number 23
[   88.705075][ T6082] em28xx 8-1:0.132: Disconnecting em28xx
[   88.780426][   T54] em28xx 8-1:0.132: Config register raw data: 0xffffffed
[   88.783997][   T54] em28xx 8-1:0.132: AC97 chip type couldn't be determined
[   88.786770][   T54] em28xx 8-1:0.132: No AC97 audio processor
[   88.790519][   T54] usb 8-1: Decoder not found
[   88.792684][   T54] em28xx 8-1:0.132: failed to create media graph
[   88.795320][   T54] em28xx 8-1:0.132: V4L2 device video103 deregistered
[   88.799436][   T54] em28xx 8-1:0.132: Remote control support is not available for this card.
[   88.803273][ T6082] em28xx 8-1:0.132: Closing input extension
[   88.808669][ T6082] em28xx 8-1:0.132: Freeing device
[   88.821848][   T34] usb 5-1: Using ep0 maxpacket: 32
[   88.824713][   T34] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[   88.827252][   T34] usb 5-1: config 0 has no interface number 0
[   88.829149][   T34] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   88.834061][   T34] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   88.837595][   T34] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   88.840141][   T34] usb 5-1: Product: syz
[   88.841460][   T34] usb 5-1: Manufacturer: syz
[   88.843495][   T34] usb 5-1: SerialNumber: syz
[   88.846408][   T34] usb 5-1: config 0 descriptor??
[   88.848435][ T6743] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[   88.852064][ T6166] em28xx 7-1:0.132: unknown em28xx chip ID (0)
[   88.852382][   T34] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   88.857033][   T34] em28xx 5-1:0.132: Video interface 132 found: bulk
[   88.916385][ T6166] em28xx 7-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   88.919746][ T6166] em28xx 7-1:0.132: board has no eeprom
[   88.942678][   T61] em28xx 6-1:0.132: unknown em28xx chip ID (0)
[   88.982922][ T6166] em28xx 7-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   88.986025][ T6166] em28xx 7-1:0.132: analog set to bulk mode.
[   88.988764][   T60] em28xx 7-1:0.132: Registering V4L2 extension
[   88.992680][ T6166] usb 7-1: USB disconnect, device number 27
[   88.995555][ T6166] em28xx 7-1:0.132: Disconnecting em28xx
[   89.003635][   T61] em28xx 6-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   89.007073][   T61] em28xx 6-1:0.132: board has no eeprom
[   89.050834][   T60] em28xx 7-1:0.132: Config register raw data: 0xffffffed
[   89.053673][   T60] em28xx 7-1:0.132: AC97 chip type couldn't be determined
[   89.056420][   T60] em28xx 7-1:0.132: No AC97 audio processor
[   89.059610][   T60] usb 7-1: Decoder not found
[   89.061413][   T60] em28xx 7-1:0.132: failed to create media graph
[   89.061994][   T61] em28xx 6-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   89.066510][   T61] em28xx 6-1:0.132: analog set to bulk mode.
[   89.066562][   T60] em28xx 7-1:0.132: V4L2 device video103 deregistered
[   89.073147][   T60] em28xx 7-1:0.132: Remote control support is not available for this card.
[   89.073454][   T61] usb 6-1: USB disconnect, device number 23
[   89.076845][ T6166] em28xx 7-1:0.132: Closing input extension
[   89.078895][   T61] em28xx 6-1:0.132: Disconnecting em28xx
[   89.082746][ T3579] em28xx 6-1:0.132: Registering V4L2 extension
[   89.083636][ T6166] em28xx 7-1:0.132: Freeing device
[   89.112155][   T34] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[   89.156209][ T3579] em28xx 6-1:0.132: Config register raw data: 0xffffffed
[   89.159476][ T3579] em28xx 6-1:0.132: AC97 chip type couldn't be determined
[   89.162671][ T3579] em28xx 6-1:0.132: No AC97 audio processor
[   89.166456][ T3579] usb 6-1: Decoder not found
[   89.168405][ T3579] em28xx 6-1:0.132: failed to create media graph
[   89.171147][ T3579] em28xx 6-1:0.132: V4L2 device video103 deregistered
[   89.174004][   T34] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   89.174020][   T34] em28xx 5-1:0.132: board has no eeprom
[   89.182502][ T3579] em28xx 6-1:0.132: Remote control support is not available for this card.
[   89.186181][   T61] em28xx 6-1:0.132: Closing input extension
[   89.191646][   T61] em28xx 6-1:0.132: Freeing device
[   89.233745][   T34] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   89.236993][   T34] em28xx 5-1:0.132: analog set to bulk mode.
[   89.243366][   T54] em28xx 5-1:0.132: Registering V4L2 extension
[   89.247755][   T34] usb 5-1: USB disconnect, device number 24
[   89.253876][   T34] em28xx 5-1:0.132: Disconnecting em28xx
[   89.271899][ T6210] usb 8-1: new high-speed USB device number 24 using dummy_hcd
[   89.314634][   T54] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[   89.317464][   T54] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[   89.320273][   T54] em28xx 5-1:0.132: No AC97 audio processor
[   89.323985][   T54] usb 5-1: Decoder not found
[   89.325872][   T54] em28xx 5-1:0.132: failed to create media graph
[   89.328430][   T54] em28xx 5-1:0.132: V4L2 device video103 deregistered
[   89.332343][   T54] em28xx 5-1:0.132: Remote control support is not available for this card.
[   89.335521][   T34] em28xx 5-1:0.132: Closing input extension
[   89.339312][   T34] em28xx 5-1:0.132: Freeing device
[   89.441912][ T6210] usb 8-1: Using ep0 maxpacket: 32
[   89.445377][ T6210] usb 8-1: config 0 has an invalid interface number: 132 but max is 0
[   89.448001][ T6210] usb 8-1: config 0 has no interface number 0
[   89.450175][ T6210] usb 8-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   89.455935][ T6210] usb 8-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   89.459028][ T6210] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   89.461910][ T6210] usb 8-1: Product: syz
[   89.463288][ T6210] usb 8-1: Manufacturer: syz
[   89.464768][ T6210] usb 8-1: SerialNumber: syz
[   89.467485][ T6210] usb 8-1: config 0 descriptor??
[   89.469585][ T6751] raw-gadget.0 gadget.3: fail, usb_ep_enable returned -22
[   89.473819][ T6210] em28xx 8-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   89.476867][ T6210] em28xx 8-1:0.132: Video interface 132 found: bulk
[   89.541972][ T6082] usb 7-1: new high-speed USB device number 28 using dummy_hcd
[   89.632001][ T6055] usb 6-1: new high-speed USB device number 24 using dummy_hcd
[   89.691997][ T6082] usb 7-1: Using ep0 maxpacket: 32
[   89.695950][ T6082] usb 7-1: config 0 has an invalid interface number: 132 but max is 0
[   89.699010][ T6082] usb 7-1: config 0 has no interface number 0
[   89.701543][ T6082] usb 7-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   89.707740][ T6082] usb 7-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   89.711498][ T6082] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   89.714945][ T6082] usb 7-1: Product: syz
[   89.716691][ T6082] usb 7-1: Manufacturer: syz
[   89.718657][ T6082] usb 7-1: SerialNumber: syz
[   89.722893][ T6082] usb 7-1: config 0 descriptor??
[   89.725749][ T6762] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[   89.731231][ T6082] em28xx 7-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   89.733042][ T6210] em28xx 8-1:0.132: unknown em28xx chip ID (0)
[   89.735371][ T6082] em28xx 7-1:0.132: Video interface 132 found: bulk
[   89.781898][ T6055] usb 6-1: Using ep0 maxpacket: 32
[   89.785372][ T6055] usb 6-1: config 0 has an invalid interface number: 132 but max is 0
[   89.788412][ T6055] usb 6-1: config 0 has no interface number 0
[   89.790772][ T6055] usb 6-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   89.796245][ T6210] em28xx 8-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   89.799444][ T6210] em28xx 8-1:0.132: board has no eeprom
[   89.801969][   T10] usb 5-1: new high-speed USB device number 25 using dummy_hcd
[   89.804773][ T6055] usb 6-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   89.807772][ T6055] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   89.810209][ T6055] usb 6-1: Product: syz
[   89.811698][ T6055] usb 6-1: Manufacturer: syz
[   89.813322][ T6055] usb 6-1: SerialNumber: syz
[   89.816262][ T6055] usb 6-1: config 0 descriptor??
[   89.818569][ T6765] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[   89.823303][ T6055] em28xx 6-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   89.826541][ T6055] em28xx 6-1:0.132: Video interface 132 found: bulk
[   89.851859][ T6210] em28xx 8-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   89.854988][ T6210] em28xx 8-1:0.132: analog set to bulk mode.
[   89.857895][    T9] em28xx 8-1:0.132: Registering V4L2 extension
[   89.862905][ T6210] usb 8-1: USB disconnect, device number 24
[   89.866431][ T6210] em28xx 8-1:0.132: Disconnecting em28xx
[   89.920375][    T9] em28xx 8-1:0.132: Config register raw data: 0xffffffed
[   89.923201][    T9] em28xx 8-1:0.132: AC97 chip type couldn't be determined
[   89.925984][    T9] em28xx 8-1:0.132: No AC97 audio processor
[   89.929584][    T9] usb 8-1: Decoder not found
[   89.931401][    T9] em28xx 8-1:0.132: failed to create media graph
[   89.934193][    T9] em28xx 8-1:0.132: V4L2 device video103 deregistered
[   89.937099][    T9] em28xx 8-1:0.132: Remote control support is not available for this card.
[   89.940517][ T6210] em28xx 8-1:0.132: Closing input extension
[   89.946079][ T6210] em28xx 8-1:0.132: Freeing device
[   89.961841][   T10] usb 5-1: Using ep0 maxpacket: 32
[   89.965170][   T10] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[   89.968261][   T10] usb 5-1: config 0 has no interface number 0
[   89.970751][   T10] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   89.977073][   T10] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   89.980652][   T10] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   89.984086][   T10] usb 5-1: Product: syz
[   89.985781][   T10] usb 5-1: Manufacturer: syz
[   89.987673][   T10] usb 5-1: SerialNumber: syz
[   89.992287][ T6082] em28xx 7-1:0.132: unknown em28xx chip ID (0)
[   89.993811][   T10] usb 5-1: config 0 descriptor??
[   89.997594][ T6767] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[   90.002533][   T10] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   90.006301][   T10] em28xx 5-1:0.132: Video interface 132 found: bulk
[   90.054530][ T6082] em28xx 7-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   90.058160][ T6082] em28xx 7-1:0.132: board has no eeprom
[   90.082295][ T6055] em28xx 6-1:0.132: unknown em28xx chip ID (0)
[   90.113876][ T6082] em28xx 7-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   90.117090][ T6082] em28xx 7-1:0.132: analog set to bulk mode.
[   90.119608][   T34] em28xx 7-1:0.132: Registering V4L2 extension
[   90.126099][ T6082] usb 7-1: USB disconnect, device number 28
[   90.129493][ T6082] em28xx 7-1:0.132: Disconnecting em28xx
[   90.154160][ T6055] em28xx 6-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   90.157700][ T6055] em28xx 6-1:0.132: board has no eeprom
[   90.198790][   T34] em28xx 7-1:0.132: Config register raw data: 0xffffffed
[   90.201743][   T34] em28xx 7-1:0.132: AC97 chip type couldn't be determined
[   90.204795][   T34] em28xx 7-1:0.132: No AC97 audio processor
[   90.209117][   T34] usb 7-1: Decoder not found
[   90.211083][   T34] em28xx 7-1:0.132: failed to create media graph
[   90.211987][ T6055] em28xx 6-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   90.213927][   T34] em28xx 7-1:0.132: V4L2 device video103 deregistered
[   90.216160][ T6055] em28xx 6-1:0.132: analog set to bulk mode.
[   90.220029][   T34] em28xx 7-1:0.132: Remote control support is not available for this card.
[   90.222576][ T6055] usb 6-1: USB disconnect, device number 24
[   90.224676][ T6082] em28xx 7-1:0.132: Closing input extension
[   90.227498][ T6055] em28xx 6-1:0.132: Disconnecting em28xx
[   90.230621][ T6210] em28xx 6-1:0.132: Registering V4L2 extension
[   90.234332][ T6082] em28xx 7-1:0.132: Freeing device
[   90.272271][   T10] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[   90.287589][ T6210] em28xx 6-1:0.132: Config register raw data: 0xffffffed
[   90.289806][ T6210] em28xx 6-1:0.132: AC97 chip type couldn't be determined
[   90.292166][ T6210] em28xx 6-1:0.132: No AC97 audio processor
[   90.294720][ T6210] usb 6-1: Decoder not found
[   90.296139][ T6210] em28xx 6-1:0.132: failed to create media graph
[   90.298065][ T6210] em28xx 6-1:0.132: V4L2 device video103 deregistered
[   90.300894][ T6210] em28xx 6-1:0.132: Remote control support is not available for this card.
[   90.303659][ T6055] em28xx 6-1:0.132: Closing input extension
[   90.307777][ T6055] em28xx 6-1:0.132: Freeing device
[   90.334515][   T10] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   90.337508][   T10] em28xx 5-1:0.132: board has no eeprom
[   90.391986][   T10] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   90.395498][   T10] em28xx 5-1:0.132: analog set to bulk mode.
[   90.398865][ T6210] em28xx 5-1:0.132: Registering V4L2 extension
[   90.402514][   T10] usb 5-1: USB disconnect, device number 25
[   90.405418][   T10] em28xx 5-1:0.132: Disconnecting em28xx
[   90.430561][ T6166] usb 8-1: new high-speed USB device number 25 using dummy_hcd
[   90.462976][ T6210] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[   90.465192][ T6210] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[   90.467423][ T6210] em28xx 5-1:0.132: No AC97 audio processor
[   90.470199][ T6210] usb 5-1: Decoder not found
[   90.471662][ T6210] em28xx 5-1:0.132: failed to create media graph
[   90.475238][ T6210] em28xx 5-1:0.132: V4L2 device video103 deregistered
[   90.478408][ T6210] em28xx 5-1:0.132: Remote control support is not available for this card.
[   90.481316][   T10] em28xx 5-1:0.132: Closing input extension
[   90.486343][   T10] em28xx 5-1:0.132: Freeing device
[   90.592045][ T6166] usb 8-1: Using ep0 maxpacket: 32
[   90.596830][ T6166] usb 8-1: config 0 has an invalid interface number: 132 but max is 0
[   90.599500][ T6166] usb 8-1: config 0 has no interface number 0
[   90.601956][ T6166] usb 8-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   90.607681][ T6166] usb 8-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   90.611365][ T6166] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   90.614685][ T6166] usb 8-1: Product: syz
[   90.616364][ T6166] usb 8-1: Manufacturer: syz
[   90.618285][ T6166] usb 8-1: SerialNumber: syz
[   90.623495][ T6166] usb 8-1: config 0 descriptor??
[   90.626339][ T6776] raw-gadget.0 gadget.3: fail, usb_ep_enable returned -22
[   90.631596][ T6166] em28xx 8-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   90.635633][ T6166] em28xx 8-1:0.132: Video interface 132 found: bulk
[   90.681946][ T3579] usb 7-1: new high-speed USB device number 29 using dummy_hcd
[   90.771849][ T6082] usb 6-1: new high-speed USB device number 25 using dummy_hcd
[   90.831866][ T3579] usb 7-1: Using ep0 maxpacket: 32
[   90.837050][ T3579] usb 7-1: config 0 has an invalid interface number: 132 but max is 0
[   90.840597][ T3579] usb 7-1: config 0 has no interface number 0
[   90.844334][ T3579] usb 7-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   90.850441][ T3579] usb 7-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   90.854306][ T3579] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   90.857702][ T3579] usb 7-1: Product: syz
[   90.859507][ T3579] usb 7-1: Manufacturer: syz
[   90.861512][ T3579] usb 7-1: SerialNumber: syz
[   90.865760][ T3579] usb 7-1: config 0 descriptor??
[   90.868698][ T6785] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[   90.874541][ T3579] em28xx 7-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   90.878629][ T3579] em28xx 7-1:0.132: Video interface 132 found: bulk
[   90.882304][ T6166] em28xx 8-1:0.132: unknown em28xx chip ID (0)
[   90.922045][ T6082] usb 6-1: Using ep0 maxpacket: 32
[   90.925763][ T6082] usb 6-1: config 0 has an invalid interface number: 132 but max is 0
[   90.929036][ T6082] usb 6-1: config 0 has no interface number 0
[   90.931092][ T6082] usb 6-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   90.936380][ T6082] usb 6-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   90.939178][ T6082] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   90.941616][ T6082] usb 6-1: Product: syz
[   90.943057][ T6082] usb 6-1: Manufacturer: syz
[   90.944997][ T6082] usb 6-1: SerialNumber: syz
[   90.949105][ T6082] usb 6-1: config 0 descriptor??
[   90.951731][ T6789] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[   90.954573][ T6166] em28xx 8-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   90.957556][ T6082] em28xx 6-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   90.958129][ T6166] em28xx 8-1:0.132: board has no eeprom
[   90.962078][ T6082] em28xx 6-1:0.132: Video interface 132 found: bulk
[   90.966378][   T60] usb 5-1: new high-speed USB device number 26 using dummy_hcd
[   91.022070][ T6166] em28xx 8-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   91.024670][ T6166] em28xx 8-1:0.132: analog set to bulk mode.
[   91.027906][ T6177] em28xx 8-1:0.132: Registering V4L2 extension
[   91.032226][ T6166] usb 8-1: USB disconnect, device number 25
[   91.034699][ T6166] em28xx 8-1:0.132: Disconnecting em28xx
[   91.086159][ T6177] em28xx 8-1:0.132: Config register raw data: 0xffffffed
[   91.088733][ T6177] em28xx 8-1:0.132: AC97 chip type couldn't be determined
[   91.091666][ T6177] em28xx 8-1:0.132: No AC97 audio processor
[   91.097113][ T6177] usb 8-1: Decoder not found
[   91.098620][ T6177] em28xx 8-1:0.132: failed to create media graph
[   91.100649][ T6177] em28xx 8-1:0.132: V4L2 device video103 deregistered
[   91.103630][ T6177] em28xx 8-1:0.132: Remote control support is not available for this card.
[   91.106377][ T6166] em28xx 8-1:0.132: Closing input extension
[   91.110465][ T6166] em28xx 8-1:0.132: Freeing device
[   91.112385][   T60] usb 5-1: Using ep0 maxpacket: 32
[   91.116918][   T60] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[   91.120092][   T60] usb 5-1: config 0 has no interface number 0
[   91.122187][   T60] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   91.129476][   T60] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   91.132100][ T3579] em28xx 7-1:0.132: unknown em28xx chip ID (0)
[   91.133314][   T60] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   91.137534][   T60] usb 5-1: Product: syz
[   91.138853][   T60] usb 5-1: Manufacturer: syz
[   91.140322][   T60] usb 5-1: SerialNumber: syz
[   91.143196][   T60] usb 5-1: config 0 descriptor??
[   91.145294][ T6791] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[   91.149189][   T60] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   91.153248][   T60] em28xx 5-1:0.132: Video interface 132 found: bulk
[   91.193639][ T3579] em28xx 7-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   91.196537][ T3579] em28xx 7-1:0.132: board has no eeprom
[   91.212209][ T6082] em28xx 6-1:0.132: unknown em28xx chip ID (0)
[   91.251950][ T3579] em28xx 7-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   91.255271][ T3579] em28xx 7-1:0.132: analog set to bulk mode.
[   91.257752][   T61] em28xx 7-1:0.132: Registering V4L2 extension
[   91.263438][ T3579] usb 7-1: USB disconnect, device number 29
[   91.266929][ T3579] em28xx 7-1:0.132: Disconnecting em28xx
[   91.282779][ T6082] em28xx 6-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   91.285553][ T6082] em28xx 6-1:0.132: board has no eeprom
[   91.329635][   T61] em28xx 7-1:0.132: Config register raw data: 0xffffffed
[   91.332055][   T61] em28xx 7-1:0.132: AC97 chip type couldn't be determined
[   91.334263][   T61] em28xx 7-1:0.132: No AC97 audio processor
[   91.338223][   T61] usb 7-1: Decoder not found
[   91.340202][   T61] em28xx 7-1:0.132: failed to create media graph
[   91.343942][ T6082] em28xx 6-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   91.345966][   T61] em28xx 7-1:0.132: V4L2 device video103 deregistered
[   91.346364][ T6082] em28xx 6-1:0.132: analog set to bulk mode.
[   91.351132][   T61] em28xx 7-1:0.132: Remote control support is not available for this card.
[   91.354676][ T3579] em28xx 7-1:0.132: Closing input extension
[   91.355153][ T6082] usb 6-1: USB disconnect, device number 25
[   91.359079][   T34] em28xx 6-1:0.132: Registering V4L2 extension
[   91.359572][ T3579] em28xx 7-1:0.132: Freeing device
[   91.375534][ T6082] em28xx 6-1:0.132: Disconnecting em28xx
[   91.413572][   T60] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[   91.424998][   T34] em28xx 6-1:0.132: Config register raw data: 0xffffffed
[   91.427247][   T34] em28xx 6-1:0.132: AC97 chip type couldn't be determined
[   91.429427][   T34] em28xx 6-1:0.132: No AC97 audio processor
[   91.433245][   T34] usb 6-1: Decoder not found
[   91.434718][   T34] em28xx 6-1:0.132: failed to create media graph
[   91.436676][   T34] em28xx 6-1:0.132: V4L2 device video103 deregistered
[   91.439430][   T34] em28xx 6-1:0.132: Remote control support is not available for this card.
[   91.446246][ T6082] em28xx 6-1:0.132: Closing input extension
[   91.449782][ T6082] em28xx 6-1:0.132: Freeing device
[   91.474883][   T60] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   91.477682][   T60] em28xx 5-1:0.132: board has no eeprom
[   91.531949][   T60] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   91.535095][   T60] em28xx 5-1:0.132: analog set to bulk mode.
[   91.538117][ T6166] em28xx 5-1:0.132: Registering V4L2 extension
[   91.544908][   T60] usb 5-1: USB disconnect, device number 26
[   91.547868][   T60] em28xx 5-1:0.132: Disconnecting em28xx
[   91.591906][   T10] usb 8-1: new high-speed USB device number 26 using dummy_hcd
[   91.598863][ T6166] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[   91.601174][ T6166] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[   91.603877][ T6166] em28xx 5-1:0.132: No AC97 audio processor
[   91.606500][ T6166] usb 5-1: Decoder not found
[   91.607956][ T6166] em28xx 5-1:0.132: failed to create media graph
[   91.609976][ T6166] em28xx 5-1:0.132: V4L2 device video103 deregistered
[   91.613057][ T6166] em28xx 5-1:0.132: Remote control support is not available for this card.
[   91.615838][   T60] em28xx 5-1:0.132: Closing input extension
[   91.619425][   T60] em28xx 5-1:0.132: Freeing device
[   91.742110][   T10] usb 8-1: Using ep0 maxpacket: 32
[   91.746356][   T10] usb 8-1: config 0 has an invalid interface number: 132 but max is 0
[   91.748951][   T10] usb 8-1: config 0 has no interface number 0
[   91.750847][   T10] usb 8-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   91.755894][   T10] usb 8-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   91.758881][   T10] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   91.761353][   T10] usb 8-1: Product: syz
[   91.763118][   T10] usb 8-1: Manufacturer: syz
[   91.764580][   T10] usb 8-1: SerialNumber: syz
[   91.767310][   T10] usb 8-1: config 0 descriptor??
[   91.770110][ T6800] raw-gadget.0 gadget.3: fail, usb_ep_enable returned -22
[   91.774778][   T10] em28xx 8-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   91.777726][   T10] em28xx 8-1:0.132: Video interface 132 found: bulk
[   91.823869][ T3579] usb 7-1: new high-speed USB device number 30 using dummy_hcd
[   91.901990][   T61] usb 6-1: new high-speed USB device number 26 using dummy_hcd
[   91.971889][ T3579] usb 7-1: Using ep0 maxpacket: 32
[   91.974910][ T3579] usb 7-1: config 0 has an invalid interface number: 132 but max is 0
[   91.977451][ T3579] usb 7-1: config 0 has no interface number 0
[   91.979387][ T3579] usb 7-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   91.984549][ T3579] usb 7-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   91.987453][ T3579] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   91.990037][ T3579] usb 7-1: Product: syz
[   91.991466][ T3579] usb 7-1: Manufacturer: syz
[   91.993270][ T3579] usb 7-1: SerialNumber: syz
[   91.996784][ T3579] usb 7-1: config 0 descriptor??
[   91.998911][ T6809] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[   92.005810][ T3579] em28xx 7-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   92.009235][ T3579] em28xx 7-1:0.132: Video interface 132 found: bulk
[   92.032213][   T10] em28xx 8-1:0.132: unknown em28xx chip ID (0)
[   92.052040][   T61] usb 6-1: Using ep0 maxpacket: 32
[   92.056936][   T61] usb 6-1: config 0 has an invalid interface number: 132 but max is 0
[   92.060093][   T61] usb 6-1: config 0 has no interface number 0
[   92.062527][   T61] usb 6-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   92.067582][   T61] usb 6-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   92.070450][   T61] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   92.073498][   T61] usb 6-1: Product: syz
[   92.075216][   T61] usb 6-1: Manufacturer: syz
[   92.077361][   T61] usb 6-1: SerialNumber: syz
[   92.082775][   T61] usb 6-1: config 0 descriptor??
[   92.086039][ T6813] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[   92.092718][   T61] em28xx 6-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   92.094995][   T10] em28xx 8-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   92.096324][   T61] em28xx 6-1:0.132: Video interface 132 found: bulk
[   92.099985][   T10] em28xx 8-1:0.132: board has no eeprom
[   92.114124][ T6210] usb 5-1: new high-speed USB device number 27 using dummy_hcd
[   92.154038][   T10] em28xx 8-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   92.157246][   T10] em28xx 8-1:0.132: analog set to bulk mode.
[   92.160421][ T6055] em28xx 8-1:0.132: Registering V4L2 extension
[   92.166165][   T10] usb 8-1: USB disconnect, device number 26
[   92.169845][   T10] em28xx 8-1:0.132: Disconnecting em28xx
[   92.222329][ T6055] em28xx 8-1:0.132: Config register raw data: 0xffffffed
[   92.224590][ T6055] em28xx 8-1:0.132: AC97 chip type couldn't be determined
[   92.226881][ T6055] em28xx 8-1:0.132: No AC97 audio processor
[   92.229395][ T6055] usb 8-1: Decoder not found
[   92.230762][ T6055] em28xx 8-1:0.132: failed to create media graph
[   92.232750][ T6055] em28xx 8-1:0.132: V4L2 device video103 deregistered
[   92.235673][ T6055] em28xx 8-1:0.132: Remote control support is not available for this card.
[   92.238824][   T10] em28xx 8-1:0.132: Closing input extension
[   92.243036][   T10] em28xx 8-1:0.132: Freeing device
[   92.262042][ T6210] usb 5-1: Using ep0 maxpacket: 32
[   92.262254][ T3579] em28xx 7-1:0.132: unknown em28xx chip ID (0)
[   92.265442][ T6210] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[   92.268814][ T6210] usb 5-1: config 0 has no interface number 0
[   92.270560][ T6210] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   92.275223][ T6210] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   92.278210][ T6210] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   92.281166][ T6210] usb 5-1: Product: syz
[   92.283401][ T6210] usb 5-1: Manufacturer: syz
[   92.285154][ T6210] usb 5-1: SerialNumber: syz
[   92.289095][ T6210] usb 5-1: config 0 descriptor??
[   92.293367][ T6815] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[   92.298700][ T6210] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   92.304557][ T6210] em28xx 5-1:0.132: Video interface 132 found: bulk
[   92.325183][ T3579] em28xx 7-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   92.327888][ T3579] em28xx 7-1:0.132: board has no eeprom
[   92.342446][   T61] em28xx 6-1:0.132: unknown em28xx chip ID (0)
[   92.381840][ T3579] em28xx 7-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   92.384300][ T3579] em28xx 7-1:0.132: analog set to bulk mode.
[   92.387858][ T6123] em28xx 7-1:0.132: Registering V4L2 extension
[   92.390207][ T3579] usb 7-1: USB disconnect, device number 30
[   92.396368][ T3579] em28xx 7-1:0.132: Disconnecting em28xx
[   92.404696][   T61] em28xx 6-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   92.408205][   T61] em28xx 6-1:0.132: board has no eeprom
[   92.454058][ T6123] em28xx 7-1:0.132: Config register raw data: 0xffffffed
[   92.456280][ T6123] em28xx 7-1:0.132: AC97 chip type couldn't be determined
[   92.458532][ T6123] em28xx 7-1:0.132: No AC97 audio processor
[   92.461331][ T6123] usb 7-1: Decoder not found
[   92.463017][ T6123] em28xx 7-1:0.132: failed to create media graph
[   92.465054][ T6123] em28xx 7-1:0.132: V4L2 device video103 deregistered
[   92.467410][   T61] em28xx 6-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   92.469895][   T61] em28xx 6-1:0.132: analog set to bulk mode.
[   92.472318][ T6123] em28xx 7-1:0.132: Remote control support is not available for this card.
[   92.475405][ T3579] em28xx 7-1:0.132: Closing input extension
[   92.478760][   T61] usb 6-1: USB disconnect, device number 26
[   92.481202][   T61] em28xx 6-1:0.132: Disconnecting em28xx
[   92.484005][ T6123] em28xx 6-1:0.132: Registering V4L2 extension
[   92.486760][ T3579] em28xx 7-1:0.132: Freeing device
[   92.552553][ T6210] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[   92.554460][ T6123] em28xx 6-1:0.132: Config register raw data: 0xffffffed
[   92.556765][ T6123] em28xx 6-1:0.132: AC97 chip type couldn't be determined
[   92.559066][ T6123] em28xx 6-1:0.132: No AC97 audio processor
[   92.562396][ T6123] usb 6-1: Decoder not found
[   92.563973][ T6123] em28xx 6-1:0.132: failed to create media graph
[   92.566187][ T6123] em28xx 6-1:0.132: V4L2 device video103 deregistered
[   92.569245][ T6123] em28xx 6-1:0.132: Remote control support is not available for this card.
[   92.573320][   T61] em28xx 6-1:0.132: Closing input extension
[   92.577649][   T61] em28xx 6-1:0.132: Freeing device
[   92.614149][ T6210] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   92.617729][ T6210] em28xx 5-1:0.132: board has no eeprom
[   92.672505][ T6210] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   92.675817][ T6210] em28xx 5-1:0.132: analog set to bulk mode.
[   92.682093][ T6055] em28xx 5-1:0.132: Registering V4L2 extension
[   92.684597][ T6210] usb 5-1: USB disconnect, device number 27
[   92.689322][ T6210] em28xx 5-1:0.132: Disconnecting em28xx
[   92.742426][   T10] usb 8-1: new high-speed USB device number 27 using dummy_hcd
[   92.756386][ T6055] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[   92.759350][ T6055] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[   92.762868][ T6055] em28xx 5-1:0.132: No AC97 audio processor
[   92.766366][ T6055] usb 5-1: Decoder not found
[   92.768239][ T6055] em28xx 5-1:0.132: failed to create media graph
[   92.770778][ T6055] em28xx 5-1:0.132: V4L2 device video103 deregistered
[   92.775125][ T6055] em28xx 5-1:0.132: Remote control support is not available for this card.
[   92.778800][ T6210] em28xx 5-1:0.132: Closing input extension
[   92.784521][ T6210] em28xx 5-1:0.132: Freeing device
[   92.892431][   T10] usb 8-1: Using ep0 maxpacket: 32
[   92.895168][   T10] usb 8-1: config 0 has an invalid interface number: 132 but max is 0
[   92.897660][   T10] usb 8-1: config 0 has no interface number 0
[   92.899579][   T10] usb 8-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   92.904676][   T10] usb 8-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   92.907621][   T10] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   92.910181][   T10] usb 8-1: Product: syz
[   92.911560][   T10] usb 8-1: Manufacturer: syz
[   92.913282][   T10] usb 8-1: SerialNumber: syz
[   92.916641][   T10] usb 8-1: config 0 descriptor??
[   92.918798][ T6827] raw-gadget.0 gadget.3: fail, usb_ep_enable returned -22
[   92.924392][   T10] em28xx 8-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   92.927596][   T10] em28xx 8-1:0.132: Video interface 132 found: bulk
[   92.952070][    T9] usb 7-1: new high-speed USB device number 31 using dummy_hcd
[   93.051872][   T61] usb 6-1: new high-speed USB device number 27 using dummy_hcd
[   93.101961][    T9] usb 7-1: Using ep0 maxpacket: 32
[   93.105141][    T9] usb 7-1: config 0 has an invalid interface number: 132 but max is 0
[   93.108011][    T9] usb 7-1: config 0 has no interface number 0
[   93.110076][    T9] usb 7-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   93.115381][    T9] usb 7-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   93.118811][    T9] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   93.121228][    T9] usb 7-1: Product: syz
[   93.122743][    T9] usb 7-1: Manufacturer: syz
[   93.124370][    T9] usb 7-1: SerialNumber: syz
[   93.127603][    T9] usb 7-1: config 0 descriptor??
[   93.129713][ T6835] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[   93.134310][    T9] em28xx 7-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   93.137923][    T9] em28xx 7-1:0.132: Video interface 132 found: bulk
[   93.182173][   T10] em28xx 8-1:0.132: unknown em28xx chip ID (0)
[   93.211830][   T61] usb 6-1: Using ep0 maxpacket: 32
[   93.214937][   T61] usb 6-1: config 0 has an invalid interface number: 132 but max is 0
[   93.217542][   T61] usb 6-1: config 0 has no interface number 0
[   93.219476][   T61] usb 6-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   93.224769][   T61] usb 6-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   93.227996][   T61] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   93.231359][   T61] usb 6-1: Product: syz
[   93.232806][   T61] usb 6-1: Manufacturer: syz
[   93.234284][   T61] usb 6-1: SerialNumber: syz
[   93.237077][   T61] usb 6-1: config 0 descriptor??
[   93.239692][ T6839] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[   93.243736][   T61] em28xx 6-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   93.246752][   T61] em28xx 6-1:0.132: Video interface 132 found: bulk
[   93.251889][ T6166] usb 5-1: new high-speed USB device number 28 using dummy_hcd
[   93.253662][   T10] em28xx 8-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   93.257670][   T10] em28xx 8-1:0.132: board has no eeprom
[   93.311819][   T10] em28xx 8-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   93.314313][   T10] em28xx 8-1:0.132: analog set to bulk mode.
[   93.318905][ T6210] em28xx 8-1:0.132: Registering V4L2 extension
[   93.320978][   T10] usb 8-1: USB disconnect, device number 27
[   93.323892][   T10] em28xx 8-1:0.132: Disconnecting em28xx
[   93.379252][ T6210] em28xx 8-1:0.132: Config register raw data: 0xffffffed
[   93.381465][ T6210] em28xx 8-1:0.132: AC97 chip type couldn't be determined
[   93.383746][ T6210] em28xx 8-1:0.132: No AC97 audio processor
[   93.386548][ T6210] usb 8-1: Decoder not found
[   93.388176][ T6210] em28xx 8-1:0.132: failed to create media graph
[   93.390242][ T6210] em28xx 8-1:0.132: V4L2 device video103 deregistered
[   93.393163][    T9] em28xx 7-1:0.132: unknown em28xx chip ID (0)
[   93.395966][ T6210] em28xx 8-1:0.132: Remote control support is not available for this card.
[   93.398892][   T10] em28xx 8-1:0.132: Closing input extension
[   93.402309][   T10] em28xx 8-1:0.132: Freeing device
[   93.404415][ T6166] usb 5-1: Using ep0 maxpacket: 32
[   93.407425][ T6166] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[   93.410476][ T6166] usb 5-1: config 0 has no interface number 0
[   93.412712][ T6166] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   93.418199][ T6166] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   93.421266][ T6166] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   93.424567][ T6166] usb 5-1: Product: syz
[   93.426005][ T6166] usb 5-1: Manufacturer: syz
[   93.427583][ T6166] usb 5-1: SerialNumber: syz
[   93.431245][ T6166] usb 5-1: config 0 descriptor??
[   93.433521][ T6842] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[   93.437513][ T6166] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   93.441204][ T6166] em28xx 5-1:0.132: Video interface 132 found: bulk
[   93.454473][    T9] em28xx 7-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   93.458035][    T9] em28xx 7-1:0.132: board has no eeprom
[   93.502240][   T61] em28xx 6-1:0.132: unknown em28xx chip ID (0)
[   93.511852][    T9] em28xx 7-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   93.514305][    T9] em28xx 7-1:0.132: analog set to bulk mode.
[   93.516981][ T6210] em28xx 7-1:0.132: Registering V4L2 extension
[   93.524719][    T9] usb 7-1: USB disconnect, device number 31
[   93.528566][    T9] em28xx 7-1:0.132: Disconnecting em28xx
[   93.564168][   T61] em28xx 6-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   93.567320][   T61] em28xx 6-1:0.132: board has no eeprom
[   93.576953][ T6210] em28xx 7-1:0.132: Config register raw data: 0xffffffed
[   93.579116][ T6210] em28xx 7-1:0.132: AC97 chip type couldn't be determined
[   93.581288][ T6210] em28xx 7-1:0.132: No AC97 audio processor
[   93.584691][ T6210] usb 7-1: Decoder not found
[   93.586161][ T6210] em28xx 7-1:0.132: failed to create media graph
[   93.588124][ T6210] em28xx 7-1:0.132: V4L2 device video103 deregistered
[   93.590992][ T6210] em28xx 7-1:0.132: Remote control support is not available for this card.
[   93.594152][    T9] em28xx 7-1:0.132: Closing input extension
[   93.598030][    T9] em28xx 7-1:0.132: Freeing device
[   93.622075][   T61] em28xx 6-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   93.625267][   T61] em28xx 6-1:0.132: analog set to bulk mode.
[   93.629481][   T61] usb 6-1: USB disconnect, device number 27
[   93.633110][   T61] em28xx 6-1:0.132: Disconnecting em28xx
[   93.635373][ T6123] em28xx 6-1:0.132: Registering V4L2 extension
2025/09/21 14:16:31 executed programs: 117
[   93.692496][ T6166] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[   93.703666][ T6123] em28xx 6-1:0.132: Config register raw data: 0xffffffed
[   93.706316][ T6123] em28xx 6-1:0.132: AC97 chip type couldn't be determined
[   93.708968][ T6123] em28xx 6-1:0.132: No AC97 audio processor
[   93.713356][ T6123] usb 6-1: Decoder not found
[   93.715263][ T6123] em28xx 6-1:0.132: failed to create media graph
[   93.717817][ T6123] em28xx 6-1:0.132: V4L2 device video103 deregistered
[   93.721517][ T6123] em28xx 6-1:0.132: Remote control support is not available for this card.
[   93.724583][   T61] em28xx 6-1:0.132: Closing input extension
[   93.729346][   T61] em28xx 6-1:0.132: Freeing device
[   93.753775][ T6166] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   93.757528][ T6166] em28xx 5-1:0.132: board has no eeprom
[   93.811824][ T6166] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   93.814403][ T6166] em28xx 5-1:0.132: analog set to bulk mode.
[   93.818592][   T60] em28xx 5-1:0.132: Registering V4L2 extension
[   93.821115][ T6166] usb 5-1: USB disconnect, device number 28
[   93.824562][ T6166] em28xx 5-1:0.132: Disconnecting em28xx
[   93.871860][   T34] usb 8-1: new high-speed USB device number 28 using dummy_hcd
[   93.886642][   T60] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[   93.889019][   T60] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[   93.891409][   T60] em28xx 5-1:0.132: No AC97 audio processor
[   93.894850][   T60] usb 5-1: Decoder not found
[   93.896396][   T60] em28xx 5-1:0.132: failed to create media graph
[   93.898338][   T60] em28xx 5-1:0.132: V4L2 device video103 deregistered
[   93.901153][   T60] em28xx 5-1:0.132: Remote control support is not available for this card.
[   93.904143][ T6166] em28xx 5-1:0.132: Closing input extension
[   93.907810][ T6166] em28xx 5-1:0.132: Freeing device
[   94.021930][   T34] usb 8-1: Using ep0 maxpacket: 32
[   94.026213][   T34] usb 8-1: config 0 has an invalid interface number: 132 but max is 0
[   94.029608][   T34] usb 8-1: config 0 has no interface number 0
[   94.033129][   T34] usb 8-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   94.039136][   T34] usb 8-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   94.042444][   T34] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   94.045232][   T34] usb 8-1: Product: syz
[   94.046976][   T34] usb 8-1: Manufacturer: syz
[   94.048574][   T34] usb 8-1: SerialNumber: syz
[   94.051961][   T34] usb 8-1: config 0 descriptor??
[   94.054276][ T6854] raw-gadget.0 gadget.3: fail, usb_ep_enable returned -22
[   94.058832][   T34] em28xx 8-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   94.062098][   T34] em28xx 8-1:0.132: Video interface 132 found: bulk
[   94.111885][    T9] usb 7-1: new high-speed USB device number 32 using dummy_hcd
[   94.192316][   T10] usb 6-1: new high-speed USB device number 28 using dummy_hcd
[   94.262057][    T9] usb 7-1: Using ep0 maxpacket: 32
[   94.266531][    T9] usb 7-1: config 0 has an invalid interface number: 132 but max is 0
[   94.269935][    T9] usb 7-1: config 0 has no interface number 0
[   94.272644][    T9] usb 7-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   94.278733][    T9] usb 7-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   94.282638][    T9] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   94.285938][    T9] usb 7-1: Product: syz
[   94.287304][    T9] usb 7-1: Manufacturer: syz
[   94.288771][    T9] usb 7-1: SerialNumber: syz
[   94.291552][    T9] usb 7-1: config 0 descriptor??
[   94.294065][ T6862] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[   94.297832][    T9] em28xx 7-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   94.300882][    T9] em28xx 7-1:0.132: Video interface 132 found: bulk
[   94.312458][   T34] em28xx 8-1:0.132: unknown em28xx chip ID (0)
[   94.341926][   T10] usb 6-1: Using ep0 maxpacket: 32
[   94.345020][   T10] usb 6-1: config 0 has an invalid interface number: 132 but max is 0
[   94.347640][   T10] usb 6-1: config 0 has no interface number 0
[   94.349617][   T10] usb 6-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   94.354777][   T10] usb 6-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   94.357730][   T10] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   94.360302][   T10] usb 6-1: Product: syz
[   94.361659][   T10] usb 6-1: Manufacturer: syz
[   94.363236][   T10] usb 6-1: SerialNumber: syz
[   94.366683][   T10] usb 6-1: config 0 descriptor??
[   94.368960][ T6866] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[   94.373426][   T10] em28xx 6-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   94.374779][   T34] em28xx 8-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   94.376451][   T10] em28xx 6-1:0.132: Video interface 132 found: bulk
[   94.379746][   T34] em28xx 8-1:0.132: board has no eeprom
[   94.391831][   T61] usb 5-1: new high-speed USB device number 29 using dummy_hcd
[   94.441870][   T34] em28xx 8-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   94.444328][   T34] em28xx 8-1:0.132: analog set to bulk mode.
[   94.446592][ T6082] em28xx 8-1:0.132: Registering V4L2 extension
[   94.454438][   T34] usb 8-1: USB disconnect, device number 28
[   94.456842][   T34] em28xx 8-1:0.132: Disconnecting em28xx
[   94.501341][ T6082] em28xx 8-1:0.132: Config register raw data: 0xffffffed
[   94.504016][ T6082] em28xx 8-1:0.132: AC97 chip type couldn't be determined
[   94.506228][ T6082] em28xx 8-1:0.132: No AC97 audio processor
[   94.509347][ T6082] usb 8-1: Decoder not found
[   94.510859][ T6082] em28xx 8-1:0.132: failed to create media graph
[   94.512974][ T6082] em28xx 8-1:0.132: V4L2 device video103 deregistered
[   94.515776][ T6082] em28xx 8-1:0.132: Remote control support is not available for this card.
[   94.518468][   T34] em28xx 8-1:0.132: Closing input extension
[   94.525372][   T34] em28xx 8-1:0.132: Freeing device
[   94.553840][   T61] usb 5-1: Using ep0 maxpacket: 32
[   94.557436][   T61] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[   94.560869][   T61] usb 5-1: config 0 has no interface number 0
[   94.562089][    T9] em28xx 7-1:0.132: unknown em28xx chip ID (0)
[   94.564350][   T61] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   94.570525][   T61] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   94.574049][   T61] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   94.577359][   T61] usb 5-1: Product: syz
[   94.579117][   T61] usb 5-1: Manufacturer: syz
[   94.581081][   T61] usb 5-1: SerialNumber: syz
[   94.585223][   T61] usb 5-1: config 0 descriptor??
[   94.587915][ T6868] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[   94.593569][   T61] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   94.597580][   T61] em28xx 5-1:0.132: Video interface 132 found: bulk
[   94.623817][    T9] em28xx 7-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   94.626666][    T9] em28xx 7-1:0.132: board has no eeprom
[   94.642657][   T10] em28xx 6-1:0.132: unknown em28xx chip ID (0)
[   94.681995][    T9] em28xx 7-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   94.684387][    T9] em28xx 7-1:0.132: analog set to bulk mode.
[   94.686657][ T6210] em28xx 7-1:0.132: Registering V4L2 extension
[   94.690618][    T9] usb 7-1: USB disconnect, device number 32
[   94.693833][    T9] em28xx 7-1:0.132: Disconnecting em28xx
[   94.704143][   T10] em28xx 6-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   94.707202][   T10] em28xx 6-1:0.132: board has no eeprom
[   94.761857][   T10] em28xx 6-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   94.764716][   T10] em28xx 6-1:0.132: analog set to bulk mode.
[   94.769613][   T10] usb 6-1: USB disconnect, device number 28
[   94.771600][ T6210] em28xx 7-1:0.132: Config register raw data: 0xffffffed
[   94.774354][ T6210] em28xx 7-1:0.132: AC97 chip type couldn't be determined
[   94.777077][ T6210] em28xx 7-1:0.132: No AC97 audio processor
[   94.780939][ T6210] usb 7-1: Decoder not found
[   94.784799][ T6210] em28xx 7-1:0.132: failed to create media graph
[   94.787299][ T6210] em28xx 7-1:0.132: V4L2 device video103 deregistered
[   94.790880][   T10] em28xx 6-1:0.132: Disconnecting em28xx
[   94.794105][ T6210] em28xx 7-1:0.132: Remote control support is not available for this card.
[   94.797666][ T6055] em28xx 6-1:0.132: Registering V4L2 extension
[   94.862292][   T61] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[   94.883143][ T6055] em28xx 6-1:0.132: Config register raw data: 0xffffffed
[   94.886070][ T6055] em28xx 6-1:0.132: AC97 chip type couldn't be determined
[   94.888295][ T6055] em28xx 6-1:0.132: No AC97 audio processor
[   94.890990][ T6055] usb 6-1: Decoder not found
[   94.892533][ T6055] em28xx 6-1:0.132: failed to create media graph
[   94.894544][ T6055] em28xx 6-1:0.132: V4L2 device video103 deregistered
[   94.897473][ T6055] em28xx 6-1:0.132: Remote control support is not available for this card.
[   94.900409][    T9] em28xx 7-1:0.132: Closing input extension
[   94.902603][   T10] em28xx 6-1:0.132: Closing input extension
[   94.909450][    T9] em28xx 7-1:0.132: Freeing device
[   94.913154][   T10] em28xx 6-1:0.132: Freeing device
[   94.936324][   T61] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   94.944968][   T61] em28xx 5-1:0.132: board has no eeprom
[   95.011834][   T61] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   95.014274][   T61] em28xx 5-1:0.132: analog set to bulk mode.
[   95.016113][ T6123] usb 8-1: new high-speed USB device number 29 using dummy_hcd
[   95.018580][ T3579] em28xx 5-1:0.132: Registering V4L2 extension
[   95.023203][   T61] usb 5-1: USB disconnect, device number 29
[   95.026739][   T61] em28xx 5-1:0.132: Disconnecting em28xx
[   95.111908][ T3579] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[   95.114208][ T3579] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[   95.116415][ T3579] em28xx 5-1:0.132: No AC97 audio processor
[   95.119043][ T3579] usb 5-1: Decoder not found
[   95.120569][ T3579] em28xx 5-1:0.132: failed to create media graph
[   95.122685][ T3579] em28xx 5-1:0.132: V4L2 device video103 deregistered
[   95.126197][ T3579] em28xx 5-1:0.132: Remote control support is not available for this card.
[   95.130076][   T61] em28xx 5-1:0.132: Closing input extension
[   95.135062][   T61] em28xx 5-1:0.132: Freeing device
[   95.138071][ T5975] udevd[5975]: setting mode of /dev/bus/usb/005/029 to 020664 failed: No such file or directory
[   95.143203][ T5975] udevd[5975]: setting owner of /dev/bus/usb/005/029 to uid=0, gid=0 failed: No such file or directory
[   95.171880][ T6123] usb 8-1: Using ep0 maxpacket: 32
[   95.174930][ T6123] usb 8-1: config 0 has an invalid interface number: 132 but max is 0
[   95.177532][ T6123] usb 8-1: config 0 has no interface number 0
[   95.179429][ T6123] usb 8-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   95.185273][ T6123] usb 8-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   95.188118][ T6123] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   95.190653][ T6123] usb 8-1: Product: syz
[   95.192246][ T6123] usb 8-1: Manufacturer: syz
[   95.193722][ T6123] usb 8-1: SerialNumber: syz
[   95.196416][ T6123] usb 8-1: config 0 descriptor??
[   95.198534][ T6879] raw-gadget.0 gadget.3: fail, usb_ep_enable returned -22
[   95.203042][ T6123] em28xx 8-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   95.206162][ T6123] em28xx 8-1:0.132: Video interface 132 found: bulk
[   95.331921][ T6527] usb 6-1: new high-speed USB device number 29 using dummy_hcd
[   95.331926][    T9] usb 7-1: new high-speed USB device number 33 using dummy_hcd
[   95.462359][ T6123] em28xx 8-1:0.132: unknown em28xx chip ID (0)
[   95.481863][ T6527] usb 6-1: Using ep0 maxpacket: 32
[   95.481863][    T9] usb 7-1: Using ep0 maxpacket: 32
[   95.484934][ T6527] usb 6-1: config 0 has an invalid interface number: 132 but max is 0
[   95.487519][    T9] usb 7-1: config 0 has an invalid interface number: 132 but max is 0
[   95.488240][ T6527] usb 6-1: config 0 has no interface number 0
[   95.492003][    T9] usb 7-1: config 0 has no interface number 0
[   95.493783][ T6527] usb 6-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   95.496176][    T9] usb 7-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   95.501701][ T6527] usb 6-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   95.506612][    T9] usb 7-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   95.507849][ T6527] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   95.511466][    T9] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   95.511485][    T9] usb 7-1: Product: syz
[   95.511498][    T9] usb 7-1: Manufacturer: syz
[   95.511510][    T9] usb 7-1: SerialNumber: syz
[   95.513642][    T9] usb 7-1: config 0 descriptor??
[   95.514881][ T6527] usb 6-1: Product: syz
[   95.518926][ T6887] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[   95.519971][ T6527] usb 6-1: Manufacturer: syz
[   95.524815][    T9] em28xx 7-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   95.528292][ T6527] usb 6-1: SerialNumber: syz
[   95.528652][    T9] em28xx 7-1:0.132: Video interface 132 found: bulk
[   95.534195][ T6123] em28xx 8-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   95.546346][   T61] usb 5-1: new high-speed USB device number 30 using dummy_hcd
[   95.549456][ T6527] usb 6-1: config 0 descriptor??
[   95.552309][ T6123] em28xx 8-1:0.132: board has no eeprom
[   95.552382][ T6892] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[   95.559559][ T6527] em28xx 6-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   95.563639][ T6527] em28xx 6-1:0.132: Video interface 132 found: bulk
[   95.611844][ T6123] em28xx 8-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   95.615279][ T6123] em28xx 8-1:0.132: analog set to bulk mode.
[   95.618844][ T6128] em28xx 8-1:0.132: Registering V4L2 extension
[   95.624262][ T6123] usb 8-1: USB disconnect, device number 29
[   95.627015][ T6123] em28xx 8-1:0.132: Disconnecting em28xx
[   95.701953][ T6128] em28xx 8-1:0.132: Config register raw data: 0xffffffed
[   95.705084][ T6128] em28xx 8-1:0.132: AC97 chip type couldn't be determined
[   95.708289][ T6128] em28xx 8-1:0.132: No AC97 audio processor
[   95.711880][   T61] usb 5-1: Using ep0 maxpacket: 32
[   95.716432][ T6128] usb 8-1: Decoder not found
[   95.718556][ T6128] em28xx 8-1:0.132: failed to create media graph
[   95.721313][ T6128] em28xx 8-1:0.132: V4L2 device video103 deregistered
[   95.725014][   T61] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[   95.728534][   T61] usb 5-1: config 0 has no interface number 0
[   95.731291][   T61] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   95.737423][ T6128] em28xx 8-1:0.132: Remote control support is not available for this card.
[   95.741482][ T6123] em28xx 8-1:0.132: Closing input extension
[   95.747320][   T61] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   95.751244][   T61] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   95.756004][   T61] usb 5-1: Product: syz
[   95.758297][   T61] usb 5-1: Manufacturer: syz
[   95.760440][   T61] usb 5-1: SerialNumber: syz
[   95.763585][ T6123] em28xx 8-1:0.132: Freeing device
[   95.771130][   T61] usb 5-1: config 0 descriptor??
[   95.774729][ T6895] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[   95.780677][   T61] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   95.782440][    T9] em28xx 7-1:0.132: unknown em28xx chip ID (0)
[   95.785185][   T61] em28xx 5-1:0.132: Video interface 132 found: bulk
[   95.813236][ T6527] em28xx 6-1:0.132: unknown em28xx chip ID (0)
[   95.844410][    T9] em28xx 7-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   95.847819][    T9] em28xx 7-1:0.132: board has no eeprom
[   95.876290][ T6527] em28xx 6-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   95.880116][ T6527] em28xx 6-1:0.132: board has no eeprom
[   95.901826][    T9] em28xx 7-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   95.905003][    T9] em28xx 7-1:0.132: analog set to bulk mode.
[   95.907206][   T10] em28xx 7-1:0.132: Registering V4L2 extension
[   95.917064][    T9] usb 7-1: USB disconnect, device number 33
[   95.920449][    T9] em28xx 7-1:0.132: Disconnecting em28xx
[   95.941958][ T6527] em28xx 6-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   95.944447][ T6527] em28xx 6-1:0.132: analog set to bulk mode.
[   95.950907][ T6527] usb 6-1: USB disconnect, device number 29
[   95.954145][ T6527] em28xx 6-1:0.132: Disconnecting em28xx
[   95.968048][   T10] em28xx 7-1:0.132: Config register raw data: 0xffffffed
[   95.970591][   T10] em28xx 7-1:0.132: AC97 chip type couldn't be determined
[   95.975672][   T10] em28xx 7-1:0.132: No AC97 audio processor
[   95.978698][   T10] usb 7-1: Decoder not found
[   95.980488][   T10] em28xx 7-1:0.132: failed to create media graph
[   95.982886][   T10] em28xx 7-1:0.132: V4L2 device video103 deregistered
[   95.986378][   T10] em28xx 7-1:0.132: Remote control support is not available for this card.
[   95.989568][    T9] em28xx 7-1:0.132: Closing input extension
[   95.992197][ T6128] em28xx 6-1:0.132: Registering V4L2 extension
[   95.994753][    T9] em28xx 7-1:0.132: Freeing device
[   96.042210][   T61] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[   96.049998][ T6128] em28xx 6-1:0.132: Config register raw data: 0xffffffed
[   96.053144][ T6128] em28xx 6-1:0.132: AC97 chip type couldn't be determined
[   96.055508][ T6128] em28xx 6-1:0.132: No AC97 audio processor
[   96.059061][ T6128] usb 6-1: Decoder not found
[   96.060560][ T6128] em28xx 6-1:0.132: failed to create media graph
[   96.062659][ T6128] em28xx 6-1:0.132: V4L2 device video103 deregistered
[   96.065520][ T6128] em28xx 6-1:0.132: Remote control support is not available for this card.
[   96.068354][ T6527] em28xx 6-1:0.132: Closing input extension
[   96.075336][ T6527] em28xx 6-1:0.132: Freeing device
[   96.114257][   T61] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   96.116986][   T61] em28xx 5-1:0.132: board has no eeprom
[   96.174646][   T61] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   96.177119][   T61] em28xx 5-1:0.132: analog set to bulk mode.
[   96.179814][ T6128] em28xx 5-1:0.132: Registering V4L2 extension
[   96.183207][   T61] usb 5-1: USB disconnect, device number 30
[   96.185597][   T61] em28xx 5-1:0.132: Disconnecting em28xx
[   96.239904][ T6128] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[   96.242455][ T6128] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[   96.244669][ T6128] em28xx 5-1:0.132: No AC97 audio processor
[   96.247397][ T6128] usb 5-1: Decoder not found
[   96.248829][ T6128] em28xx 5-1:0.132: failed to create media graph
[   96.250788][ T6128] em28xx 5-1:0.132: V4L2 device video103 deregistered
[   96.253746][ T6128] em28xx 5-1:0.132: Remote control support is not available for this card.
[   96.256424][   T61] em28xx 5-1:0.132: Closing input extension
[   96.260178][   T61] em28xx 5-1:0.132: Freeing device
[   96.281857][ T6123] usb 8-1: new high-speed USB device number 30 using dummy_hcd
[   96.441990][ T6123] usb 8-1: Using ep0 maxpacket: 32
[   96.445043][ T6123] usb 8-1: config 0 has an invalid interface number: 132 but max is 0
[   96.447650][ T6123] usb 8-1: config 0 has no interface number 0
[   96.449592][ T6123] usb 8-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   96.455058][ T6123] usb 8-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   96.457867][ T6123] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   96.460328][ T6123] usb 8-1: Product: syz
[   96.461652][ T6123] usb 8-1: Manufacturer: syz
[   96.463287][ T6123] usb 8-1: SerialNumber: syz
[   96.466119][ T6123] usb 8-1: config 0 descriptor??
[   96.468140][ T6902] raw-gadget.0 gadget.3: fail, usb_ep_enable returned -22
[   96.471987][ T6123] em28xx 8-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   96.474985][ T6123] em28xx 8-1:0.132: Video interface 132 found: bulk
[   96.491861][   T60] usb 7-1: new high-speed USB device number 34 using dummy_hcd
[   96.501956][   T34] usb 6-1: new high-speed USB device number 30 using dummy_hcd
[   96.642083][   T60] usb 7-1: Using ep0 maxpacket: 32
[   96.645368][   T60] usb 7-1: config 0 has an invalid interface number: 132 but max is 0
[   96.648187][   T60] usb 7-1: config 0 has no interface number 0
[   96.650814][   T60] usb 7-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   96.657014][   T60] usb 7-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   96.659848][   T60] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   96.661894][   T34] usb 6-1: Using ep0 maxpacket: 32
[   96.662695][   T60] usb 7-1: Product: syz
[   96.666074][   T60] usb 7-1: Manufacturer: syz
[   96.666168][   T34] usb 6-1: config 0 has an invalid interface number: 132 but max is 0
[   96.667553][   T60] usb 7-1: SerialNumber: syz
[   96.668982][   T60] usb 7-1: config 0 descriptor??
[   96.670676][   T34] usb 6-1: config 0 has no interface number 0
[   96.674189][ T6914] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[   96.675981][   T34] usb 6-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   96.681494][   T60] em28xx 7-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   96.682883][   T34] usb 6-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   96.684746][   T60] em28xx 7-1:0.132: Video interface 132 found: bulk
[   96.687464][   T34] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   96.692098][   T34] usb 6-1: Product: syz
[   96.693411][   T34] usb 6-1: Manufacturer: syz
[   96.694892][   T34] usb 6-1: SerialNumber: syz
[   96.699840][   T34] usb 6-1: config 0 descriptor??
[   96.702026][ T6916] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[   96.706066][   T34] em28xx 6-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   96.709061][   T34] em28xx 6-1:0.132: Video interface 132 found: bulk
[   96.721953][   T61] usb 5-1: new high-speed USB device number 31 using dummy_hcd
[   96.732254][ T6123] em28xx 8-1:0.132: unknown em28xx chip ID (0)
[   96.793609][ T6123] em28xx 8-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   96.796708][ T6123] em28xx 8-1:0.132: board has no eeprom
[   96.852065][ T6123] em28xx 8-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   96.855383][ T6123] em28xx 8-1:0.132: analog set to bulk mode.
[   96.859158][ T6527] em28xx 8-1:0.132: Registering V4L2 extension
[   96.864219][ T6123] usb 8-1: USB disconnect, device number 30
[   96.867381][ T6123] em28xx 8-1:0.132: Disconnecting em28xx
[   96.871838][   T61] usb 5-1: Using ep0 maxpacket: 32
[   96.874712][   T61] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[   96.877506][   T61] usb 5-1: config 0 has no interface number 0
[   96.880007][   T61] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   96.884667][   T61] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   96.887614][   T61] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   96.890298][   T61] usb 5-1: Product: syz
[   96.891622][   T61] usb 5-1: Manufacturer: syz
[   96.893223][   T61] usb 5-1: SerialNumber: syz
[   96.896808][   T61] usb 5-1: config 0 descriptor??
[   96.899661][ T6919] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[   96.914223][   T61] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   96.918144][   T61] em28xx 5-1:0.132: Video interface 132 found: bulk
[   96.942828][   T60] em28xx 7-1:0.132: unknown em28xx chip ID (0)
[   96.962187][   T34] em28xx 6-1:0.132: unknown em28xx chip ID (0)
[   96.962630][ T6527] em28xx 8-1:0.132: Config register raw data: 0xffffffed
[   96.967467][ T6527] em28xx 8-1:0.132: AC97 chip type couldn't be determined
[   96.970489][ T6527] em28xx 8-1:0.132: No AC97 audio processor
[   96.976022][ T6527] usb 8-1: Decoder not found
[   96.978089][ T6527] em28xx 8-1:0.132: failed to create media graph
[   96.980822][ T6527] em28xx 8-1:0.132: V4L2 device video103 deregistered
[   96.989553][ T6527] em28xx 8-1:0.132: Remote control support is not available for this card.
[   96.993392][ T6123] em28xx 8-1:0.132: Closing input extension
[   97.000181][ T6123] em28xx 8-1:0.132: Freeing device
[   97.003649][   T60] em28xx 7-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   97.006365][   T60] em28xx 7-1:0.132: board has no eeprom
[   97.024013][   T34] em28xx 6-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   97.027738][   T34] em28xx 6-1:0.132: board has no eeprom
[   97.071819][   T60] em28xx 7-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   97.074854][   T60] em28xx 7-1:0.132: analog set to bulk mode.
[   97.077814][ T6177] em28xx 7-1:0.132: Registering V4L2 extension
[   97.081176][   T60] usb 7-1: USB disconnect, device number 34
[   97.083769][   T34] em28xx 6-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   97.084653][   T60] em28xx 7-1:0.132: Disconnecting em28xx
[   97.086890][   T34] em28xx 6-1:0.132: analog set to bulk mode.
[   97.099510][   T34] usb 6-1: USB disconnect, device number 30
[   97.104062][   T34] em28xx 6-1:0.132: Disconnecting em28xx
[   97.162102][   T61] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[   97.162108][ T6177] em28xx 7-1:0.132: Config register raw data: 0xffffffed
[   97.166218][ T6177] em28xx 7-1:0.132: AC97 chip type couldn't be determined
[   97.168330][ T6177] em28xx 7-1:0.132: No AC97 audio processor
[   97.170854][ T6177] usb 7-1: Decoder not found
[   97.174437][ T6177] em28xx 7-1:0.132: failed to create media graph
[   97.176535][ T6177] em28xx 7-1:0.132: V4L2 device video103 deregistered
[   97.181281][ T6177] em28xx 7-1:0.132: Remote control support is not available for this card.
[   97.184867][   T60] em28xx 7-1:0.132: Closing input extension
[   97.187217][ T6430] em28xx 6-1:0.132: Registering V4L2 extension
[   97.191715][   T60] em28xx 7-1:0.132: Freeing device
[   97.237571][   T61] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   97.240236][   T61] em28xx 5-1:0.132: board has no eeprom
[   97.268511][ T6430] em28xx 6-1:0.132: Config register raw data: 0xffffffed
[   97.270773][ T6430] em28xx 6-1:0.132: AC97 chip type couldn't be determined
[   97.273227][ T6430] em28xx 6-1:0.132: No AC97 audio processor
[   97.276188][ T6430] usb 6-1: Decoder not found
[   97.278120][ T6430] em28xx 6-1:0.132: failed to create media graph
[   97.280103][ T6430] em28xx 6-1:0.132: V4L2 device video103 deregistered
[   97.285554][ T6430] em28xx 6-1:0.132: Remote control support is not available for this card.
[   97.288338][   T34] em28xx 6-1:0.132: Closing input extension
[   97.291971][   T34] em28xx 6-1:0.132: Freeing device
[   97.302927][   T61] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   97.306539][   T61] em28xx 5-1:0.132: analog set to bulk mode.
[   97.311735][   T61] usb 5-1: USB disconnect, device number 31
[   97.314482][   T61] em28xx 5-1:0.132: Disconnecting em28xx
[   97.316269][ T6527] em28xx 5-1:0.132: Registering V4L2 extension
[   97.380248][ T6527] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[   97.383185][ T6527] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[   97.385897][ T6527] em28xx 5-1:0.132: No AC97 audio processor
[   97.389308][ T6527] usb 5-1: Decoder not found
[   97.391180][ T6527] em28xx 5-1:0.132: failed to create media graph
[   97.393954][ T6527] em28xx 5-1:0.132: V4L2 device video103 deregistered
[   97.398018][ T6527] em28xx 5-1:0.132: Remote control support is not available for this card.
[   97.401393][   T61] em28xx 5-1:0.132: Closing input extension
[   97.407715][   T61] em28xx 5-1:0.132: Freeing device
[   97.521875][ T6123] usb 8-1: new high-speed USB device number 31 using dummy_hcd
[   97.651873][   T60] usb 7-1: new high-speed USB device number 35 using dummy_hcd
[   97.682207][ T6123] usb 8-1: Using ep0 maxpacket: 32
[   97.685262][ T6123] usb 8-1: config 0 has an invalid interface number: 132 but max is 0
[   97.688349][ T6123] usb 8-1: config 0 has no interface number 0
[   97.690694][ T6123] usb 8-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   97.695429][ T6123] usb 8-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   97.698376][ T6123] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   97.700860][ T6123] usb 8-1: Product: syz
[   97.702271][ T6123] usb 8-1: Manufacturer: syz
[   97.703690][ T6123] usb 8-1: SerialNumber: syz
[   97.706740][ T6123] usb 8-1: config 0 descriptor??
[   97.708810][ T6928] raw-gadget.0 gadget.3: fail, usb_ep_enable returned -22
[   97.712912][ T6123] em28xx 8-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   97.715988][ T6123] em28xx 8-1:0.132: Video interface 132 found: bulk
[   97.742010][   T34] usb 6-1: new high-speed USB device number 31 using dummy_hcd
[   97.811825][   T60] usb 7-1: Using ep0 maxpacket: 32
[   97.814684][   T60] usb 7-1: config 0 has an invalid interface number: 132 but max is 0
[   97.817246][   T60] usb 7-1: config 0 has no interface number 0
[   97.819081][   T60] usb 7-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   97.823781][   T60] usb 7-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   97.826510][   T60] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   97.829024][   T60] usb 7-1: Product: syz
[   97.830349][   T60] usb 7-1: Manufacturer: syz
[   97.831909][   T60] usb 7-1: SerialNumber: syz
[   97.834789][   T60] usb 7-1: config 0 descriptor??
[   97.836878][ T6938] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[   97.840864][   T60] em28xx 7-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   97.844004][   T60] em28xx 7-1:0.132: Video interface 132 found: bulk
[   97.851835][ T6177] usb 5-1: new high-speed USB device number 32 using dummy_hcd
[   97.891919][   T34] usb 6-1: Using ep0 maxpacket: 32
[   97.894749][   T34] usb 6-1: config 0 has an invalid interface number: 132 but max is 0
[   97.897260][   T34] usb 6-1: config 0 has no interface number 0
[   97.899176][   T34] usb 6-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   97.903892][   T34] usb 6-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   97.906668][   T34] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   97.909050][   T34] usb 6-1: Product: syz
[   97.910343][   T34] usb 6-1: Manufacturer: syz
[   97.911836][   T34] usb 6-1: SerialNumber: syz
[   97.914912][   T34] usb 6-1: config 0 descriptor??
[   97.916801][ T6940] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[   97.920484][   T34] em28xx 6-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   97.923567][   T34] em28xx 6-1:0.132: Video interface 132 found: bulk
[   97.972057][ T6123] em28xx 8-1:0.132: unknown em28xx chip ID (0)
[   98.021801][ T6177] usb 5-1: Using ep0 maxpacket: 32
[   98.024885][ T6177] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[   98.027470][ T6177] usb 5-1: config 0 has no interface number 0
[   98.029350][ T6177] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   98.034457][ T6177] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   98.037348][ T6177] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   98.039909][ T6177] usb 5-1: Product: syz
[   98.042352][ T6177] usb 5-1: Manufacturer: syz
[   98.043825][ T6177] usb 5-1: SerialNumber: syz
[   98.045504][ T6123] em28xx 8-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   98.046496][ T6177] usb 5-1: config 0 descriptor??
[   98.049088][ T6123] em28xx 8-1:0.132: board has no eeprom
[   98.051708][ T6943] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[   98.057020][ T6177] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   98.060008][ T6177] em28xx 5-1:0.132: Video interface 132 found: bulk
[   98.103388][   T60] em28xx 7-1:0.132: unknown em28xx chip ID (0)
[   98.111874][ T6123] em28xx 8-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   98.114150][ T6123] em28xx 8-1:0.132: analog set to bulk mode.
[   98.116549][   T61] em28xx 8-1:0.132: Registering V4L2 extension
[   98.120042][ T6123] usb 8-1: USB disconnect, device number 31
[   98.123526][ T6123] em28xx 8-1:0.132: Disconnecting em28xx
[   98.169879][   T61] em28xx 8-1:0.132: Config register raw data: 0xffffffed
[   98.172593][   T34] em28xx 6-1:0.132: unknown em28xx chip ID (0)
[   98.174566][   T60] em28xx 7-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   98.174802][   T61] em28xx 8-1:0.132: AC97 chip type couldn't be determined
[   98.174813][   T61] em28xx 8-1:0.132: No AC97 audio processor
[   98.175771][   T61] usb 8-1: Decoder not found
[   98.177572][   T60] em28xx 7-1:0.132: board has no eeprom
[   98.179816][   T61] em28xx 8-1:0.132: failed to create media graph
[   98.179832][   T61] em28xx 8-1:0.132: V4L2 device video103 deregistered
[   98.180681][   T61] em28xx 8-1:0.132: Remote control support is not available for this card.
[   98.194597][ T6123] em28xx 8-1:0.132: Closing input extension
[   98.200246][ T6123] em28xx 8-1:0.132: Freeing device
[   98.233511][   T34] em28xx 6-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   98.236362][   T34] em28xx 6-1:0.132: board has no eeprom
[   98.254430][   T60] em28xx 7-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   98.257026][   T60] em28xx 7-1:0.132: analog set to bulk mode.
[   98.259301][ T6166] em28xx 7-1:0.132: Registering V4L2 extension
[   98.263924][   T60] usb 7-1: USB disconnect, device number 35
[   98.266320][   T60] em28xx 7-1:0.132: Disconnecting em28xx
[   98.291861][   T34] em28xx 6-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   98.295113][   T34] em28xx 6-1:0.132: analog set to bulk mode.
[   98.299860][   T34] usb 6-1: USB disconnect, device number 31
[   98.302769][   T34] em28xx 6-1:0.132: Disconnecting em28xx
[   98.314275][ T6177] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[   98.334816][ T6166] em28xx 7-1:0.132: Config register raw data: 0xffffffed
[   98.337054][ T6166] em28xx 7-1:0.132: AC97 chip type couldn't be determined
[   98.339320][ T6166] em28xx 7-1:0.132: No AC97 audio processor
[   98.342385][ T6166] usb 7-1: Decoder not found
[   98.343857][ T6166] em28xx 7-1:0.132: failed to create media graph
[   98.345878][ T6166] em28xx 7-1:0.132: V4L2 device video103 deregistered
[   98.348809][ T6166] em28xx 7-1:0.132: Remote control support is not available for this card.
[   98.351670][   T60] em28xx 7-1:0.132: Closing input extension
[   98.353933][ T6430] em28xx 6-1:0.132: Registering V4L2 extension
[   98.355638][   T60] em28xx 7-1:0.132: Freeing device
[   98.375455][ T6177] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   98.378446][ T6177] em28xx 5-1:0.132: board has no eeprom
[   98.426963][ T6430] em28xx 6-1:0.132: Config register raw data: 0xffffffed
[   98.432196][ T6177] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   98.436713][ T6177] em28xx 5-1:0.132: analog set to bulk mode.
[   98.437823][ T6430] em28xx 6-1:0.132: AC97 chip type couldn't be determined
[   98.440165][ T6177] usb 5-1: USB disconnect, device number 32
[   98.441499][ T6430] em28xx 6-1:0.132: No AC97 audio processor
[   98.444190][ T6177] em28xx 5-1:0.132: Disconnecting em28xx
[   98.447234][ T6430] usb 6-1: Decoder not found
[   98.449293][ T6430] em28xx 6-1:0.132: failed to create media graph
[   98.454008][ T6430] em28xx 6-1:0.132: V4L2 device video103 deregistered
[   98.457878][ T6430] em28xx 6-1:0.132: Remote control support is not available for this card.
[   98.462689][   T34] em28xx 6-1:0.132: Closing input extension
[   98.465125][ T1338] em28xx 5-1:0.132: Registering V4L2 extension
[   98.468192][   T34] em28xx 6-1:0.132: Freeing device
[   98.543569][ T1338] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[   98.546122][ T1338] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[   98.548808][ T1338] em28xx 5-1:0.132: No AC97 audio processor
[   98.558743][ T1338] usb 5-1: Decoder not found
[   98.560195][ T1338] em28xx 5-1:0.132: failed to create media graph
[   98.562829][ T1338] em28xx 5-1:0.132: V4L2 device video103 deregistered
[   98.567006][ T1338] em28xx 5-1:0.132: Remote control support is not available for this card.
[   98.570583][ T6177] em28xx 5-1:0.132: Closing input extension
[   98.574588][ T6177] em28xx 5-1:0.132: Freeing device
[   98.682228][ T6166] usb 8-1: new high-speed USB device number 32 using dummy_hcd
2025/09/21 14:16:36 executed programs: 135
[   98.791901][ T6123] usb 7-1: new high-speed USB device number 36 using dummy_hcd
[   98.851925][ T6166] usb 8-1: Using ep0 maxpacket: 32
[   98.855699][ T6166] usb 8-1: config 0 has an invalid interface number: 132 but max is 0
[   98.858586][ T6166] usb 8-1: config 0 has no interface number 0
[   98.861080][ T6166] usb 8-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   98.866765][ T6166] usb 8-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   98.870107][ T6166] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   98.873298][ T1338] usb 6-1: new high-speed USB device number 32 using dummy_hcd
[   98.876020][ T6166] usb 8-1: Product: syz
[   98.877422][ T6166] usb 8-1: Manufacturer: syz
[   98.878933][ T6166] usb 8-1: SerialNumber: syz
[   98.882328][ T6166] usb 8-1: config 0 descriptor??
[   98.884682][ T6956] raw-gadget.0 gadget.3: fail, usb_ep_enable returned -22
[   98.888440][ T6166] em28xx 8-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   98.891447][ T6166] em28xx 8-1:0.132: Video interface 132 found: bulk
[   98.971872][ T6123] usb 7-1: Using ep0 maxpacket: 32
[   98.974845][ T6123] usb 7-1: config 0 has an invalid interface number: 132 but max is 0
[   98.977404][ T6123] usb 7-1: config 0 has no interface number 0
[   98.979379][ T6123] usb 7-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   98.984196][ T6123] usb 7-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   98.987285][ T6123] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   98.990073][ T6123] usb 7-1: Product: syz
[   98.991406][ T6123] usb 7-1: Manufacturer: syz
[   98.992950][ T6123] usb 7-1: SerialNumber: syz
[   98.995698][ T6123] usb 7-1: config 0 descriptor??
[   98.998094][ T6962] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[   99.001842][ T6123] em28xx 7-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   99.004819][ T6123] em28xx 7-1:0.132: Video interface 132 found: bulk
[   99.041807][ T6177] usb 5-1: new high-speed USB device number 33 using dummy_hcd
[   99.061890][ T1338] usb 6-1: Using ep0 maxpacket: 32
[   99.065037][ T1338] usb 6-1: config 0 has an invalid interface number: 132 but max is 0
[   99.067700][ T1338] usb 6-1: config 0 has no interface number 0
[   99.069650][ T1338] usb 6-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   99.074763][ T1338] usb 6-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   99.077658][ T1338] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   99.080154][ T1338] usb 6-1: Product: syz
[   99.081508][ T1338] usb 6-1: Manufacturer: syz
[   99.083059][ T1338] usb 6-1: SerialNumber: syz
[   99.086289][ T1338] usb 6-1: config 0 descriptor??
[   99.088479][ T6965] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[   99.092297][ T1338] em28xx 6-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   99.095298][ T1338] em28xx 6-1:0.132: Video interface 132 found: bulk
[   99.142272][ T6166] em28xx 8-1:0.132: unknown em28xx chip ID (0)
[   99.203628][ T6177] usb 5-1: Using ep0 maxpacket: 32
[   99.207418][ T6166] em28xx 8-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   99.210270][ T6166] em28xx 8-1:0.132: board has no eeprom
[   99.212943][ T6177] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[   99.215509][ T6177] usb 5-1: config 0 has no interface number 0
[   99.217462][ T6177] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[   99.222321][ T6177] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[   99.225080][ T6177] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   99.227573][ T6177] usb 5-1: Product: syz
[   99.228895][ T6177] usb 5-1: Manufacturer: syz
[   99.230411][ T6177] usb 5-1: SerialNumber: syz
[   99.233478][ T6177] usb 5-1: config 0 descriptor??
[   99.235699][ T6967] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[   99.239941][ T6177] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[   99.243022][ T6177] em28xx 5-1:0.132: Video interface 132 found: bulk
[   99.262184][ T6123] em28xx 7-1:0.132: unknown em28xx chip ID (0)
[   99.271841][ T6166] em28xx 8-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   99.274412][ T6166] em28xx 8-1:0.132: analog set to bulk mode.
[   99.278315][   T60] em28xx 8-1:0.132: Registering V4L2 extension
[   99.280880][ T6166] usb 8-1: USB disconnect, device number 32
[   99.286467][ T6166] em28xx 8-1:0.132: Disconnecting em28xx
[   99.324197][ T6123] em28xx 7-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   99.326900][ T6123] em28xx 7-1:0.132: board has no eeprom
[   99.334585][   T60] em28xx 8-1:0.132: Config register raw data: 0xffffffed
[   99.336875][   T60] em28xx 8-1:0.132: AC97 chip type couldn't be determined
[   99.339140][   T60] em28xx 8-1:0.132: No AC97 audio processor
[   99.342302][   T60] usb 8-1: Decoder not found
[   99.343775][   T60] em28xx 8-1:0.132: failed to create media graph
[   99.345738][   T60] em28xx 8-1:0.132: V4L2 device video103 deregistered
[   99.348731][   T60] em28xx 8-1:0.132: Remote control support is not available for this card.
[   99.351748][ T6166] em28xx 8-1:0.132: Closing input extension
[   99.354231][ T1338] em28xx 6-1:0.132: unknown em28xx chip ID (0)
[   99.358608][ T6166] em28xx 8-1:0.132: Freeing device
[   99.382033][ T6123] em28xx 7-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   99.384858][ T6123] em28xx 7-1:0.132: analog set to bulk mode.
[   99.387092][   T61] em28xx 7-1:0.132: Registering V4L2 extension
[   99.390224][ T6123] usb 7-1: USB disconnect, device number 36
[   99.393382][ T6123] em28xx 7-1:0.132: Disconnecting em28xx
[   99.414483][ T1338] em28xx 6-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   99.417541][ T1338] em28xx 6-1:0.132: board has no eeprom
[   99.444847][   T61] em28xx 7-1:0.132: Config register raw data: 0xffffffed
[   99.447151][   T61] em28xx 7-1:0.132: AC97 chip type couldn't be determined
[   99.449338][   T61] em28xx 7-1:0.132: No AC97 audio processor
[   99.453028][   T61] usb 7-1: Decoder not found
[   99.454519][   T61] em28xx 7-1:0.132: failed to create media graph
[   99.456647][   T61] em28xx 7-1:0.132: V4L2 device video103 deregistered
[   99.459514][   T61] em28xx 7-1:0.132: Remote control support is not available for this card.
[   99.464470][ T6123] em28xx 7-1:0.132: Closing input extension
[   99.468414][ T6123] em28xx 7-1:0.132: Freeing device
[   99.471951][ T1338] em28xx 6-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   99.474351][ T1338] em28xx 6-1:0.132: analog set to bulk mode.
[   99.476512][   T60] em28xx 6-1:0.132: Registering V4L2 extension
[   99.482694][ T1338] usb 6-1: USB disconnect, device number 32
[   99.485731][ T1338] em28xx 6-1:0.132: Disconnecting em28xx
[   99.492194][ T6177] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[   99.554217][ T6177] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[   99.556965][   T60] em28xx 6-1:0.132: Config register raw data: 0xffffffed
[   99.559128][   T60] em28xx 6-1:0.132: AC97 chip type couldn't be determined
[   99.561382][ T6177] em28xx 5-1:0.132: board has no eeprom
[   99.563549][   T60] em28xx 6-1:0.132: No AC97 audio processor
[   99.566179][   T60] usb 6-1: Decoder not found
[   99.567646][   T60] em28xx 6-1:0.132: failed to create media graph
[   99.569617][   T60] em28xx 6-1:0.132: V4L2 device video103 deregistered
[   99.572450][   T60] em28xx 6-1:0.132: Remote control support is not available for this card.
[   99.575094][ T1338] em28xx 6-1:0.132: Closing input extension
[   99.578494][ T1338] em28xx 6-1:0.132: Freeing device
[   99.622068][ T6177] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[   99.629216][ T6177] em28xx 5-1:0.132: analog set to bulk mode.
[   99.633877][   T24] em28xx 5-1:0.132: Registering V4L2 extension
[   99.638052][ T6177] usb 5-1: USB disconnect, device number 33
[   99.640581][ T6177] em28xx 5-1:0.132: Disconnecting em28xx
[   99.694310][   T24] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[   99.696653][   T24] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[   99.699584][   T24] em28xx 5-1:0.132: No AC97 audio processor
[   99.702994][   T24] usb 5-1: Decoder not found
[   99.704464][   T24] em28xx 5-1:0.132: failed to create media graph
[   99.706490][   T24] em28xx 5-1:0.132: V4L2 device video103 deregistered
[   99.709185][   T24] em28xx 5-1:0.132: Remote control support is not available for this card.
[   99.714743][ T6177] em28xx 5-1:0.132: Closing input extension
[   99.720139][ T6177] em28xx 5-1:0.132: Freeing device
[   99.842820][   T60] usb 8-1: new high-speed USB device number 33 using dummy_hcd
[   99.951859][   T34] usb 7-1: new high-speed USB device number 37 using dummy_hcd
[  100.002077][   T60] usb 8-1: Using ep0 maxpacket: 32
[  100.007505][   T60] usb 8-1: config 0 has an invalid interface number: 132 but max is 0
[  100.010731][   T60] usb 8-1: config 0 has no interface number 0
[  100.013757][   T60] usb 8-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  100.020052][   T60] usb 8-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  100.024142][   T60] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  100.027415][   T60] usb 8-1: Product: syz
[  100.029260][   T60] usb 8-1: Manufacturer: syz
[  100.031118][   T60] usb 8-1: SerialNumber: syz
[  100.035412][   T60] usb 8-1: config 0 descriptor??
[  100.038252][ T6980] raw-gadget.0 gadget.3: fail, usb_ep_enable returned -22
[  100.043816][   T60] em28xx 8-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  100.047694][   T60] em28xx 8-1:0.132: Video interface 132 found: bulk
[  100.052352][   T10] usb 6-1: new high-speed USB device number 33 using dummy_hcd
[  100.101960][   T34] usb 7-1: Using ep0 maxpacket: 32
[  100.105064][   T34] usb 7-1: config 0 has an invalid interface number: 132 but max is 0
[  100.107806][   T34] usb 7-1: config 0 has no interface number 0
[  100.109863][   T34] usb 7-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  100.115612][   T34] usb 7-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  100.119312][   T34] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  100.122683][   T34] usb 7-1: Product: syz
[  100.124408][   T34] usb 7-1: Manufacturer: syz
[  100.126327][   T34] usb 7-1: SerialNumber: syz
[  100.129557][   T34] usb 7-1: config 0 descriptor??
[  100.131978][ T6986] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[  100.136500][   T34] em28xx 7-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  100.139528][   T34] em28xx 7-1:0.132: Video interface 132 found: bulk
[  100.191876][    T9] usb 5-1: new high-speed USB device number 34 using dummy_hcd
[  100.211825][   T10] usb 6-1: Using ep0 maxpacket: 32
[  100.215055][   T10] usb 6-1: config 0 has an invalid interface number: 132 but max is 0
[  100.217588][   T10] usb 6-1: config 0 has no interface number 0
[  100.219593][   T10] usb 6-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  100.224615][   T10] usb 6-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  100.227416][   T10] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  100.229909][   T10] usb 6-1: Product: syz
[  100.231196][   T10] usb 6-1: Manufacturer: syz
[  100.232681][   T10] usb 6-1: SerialNumber: syz
[  100.235513][   T10] usb 6-1: config 0 descriptor??
[  100.237630][ T6989] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[  100.242221][   T10] em28xx 6-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  100.245277][   T10] em28xx 6-1:0.132: Video interface 132 found: bulk
[  100.302229][   T60] em28xx 8-1:0.132: unknown em28xx chip ID (0)
[  100.361805][    T9] usb 5-1: Using ep0 maxpacket: 32
[  100.365028][    T9] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[  100.367668][    T9] usb 5-1: config 0 has no interface number 0
[  100.369896][    T9] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  100.375154][   T60] em28xx 8-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  100.375739][    T9] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  100.378613][   T60] em28xx 8-1:0.132: board has no eeprom
[  100.383577][    T9] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  100.386219][    T9] usb 5-1: Product: syz
[  100.387608][    T9] usb 5-1: Manufacturer: syz
[  100.389198][    T9] usb 5-1: SerialNumber: syz
[  100.392245][   T34] em28xx 7-1:0.132: unknown em28xx chip ID (0)
[  100.392664][    T9] usb 5-1: config 0 descriptor??
[  100.397234][ T6991] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[  100.402031][    T9] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  100.405230][    T9] em28xx 5-1:0.132: Video interface 132 found: bulk
[  100.431916][   T60] em28xx 8-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  100.434418][   T60] em28xx 8-1:0.132: analog set to bulk mode.
[  100.436386][ T6177] em28xx 8-1:0.132: Registering V4L2 extension
[  100.440315][   T60] usb 8-1: USB disconnect, device number 33
[  100.446992][   T60] em28xx 8-1:0.132: Disconnecting em28xx
[  100.454439][   T34] em28xx 7-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  100.458133][   T34] em28xx 7-1:0.132: board has no eeprom
[  100.497160][ T6177] em28xx 8-1:0.132: Config register raw data: 0xffffffed
[  100.499636][ T6177] em28xx 8-1:0.132: AC97 chip type couldn't be determined
[  100.502320][ T6177] em28xx 8-1:0.132: No AC97 audio processor
[  100.505349][ T6177] usb 8-1: Decoder not found
[  100.506942][ T6177] em28xx 8-1:0.132: failed to create media graph
[  100.509170][ T6177] em28xx 8-1:0.132: V4L2 device video103 deregistered
[  100.512039][ T6177] em28xx 8-1:0.132: Remote control support is not available for this card.
[  100.512126][   T10] em28xx 6-1:0.132: unknown em28xx chip ID (0)
[  100.513790][   T34] em28xx 7-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  100.513814][   T34] em28xx 7-1:0.132: analog set to bulk mode.
[  100.514779][   T60] em28xx 8-1:0.132: Closing input extension
[  100.516173][ T6430] em28xx 7-1:0.132: Registering V4L2 extension
[  100.517114][   T60] em28xx 8-1:0.132: Freeing device
[  100.531569][   T34] usb 7-1: USB disconnect, device number 37
[  100.540365][ T6430] em28xx 7-1:0.132: failed to trigger read from i2c address 0x4a (error=-19)
[  100.547305][ T6430] em28xx 7-1:0.132: failed to trigger read from i2c address 0x48 (error=-19)
[  100.551325][ T6430] em28xx 7-1:0.132: failed to trigger read from i2c address 0x42 (error=-19)
[  100.555505][ T6430] em28xx 7-1:0.132: failed to trigger read from i2c address 0x40 (error=-19)
[  100.559913][   T34] em28xx 7-1:0.132: Disconnecting em28xx
[  100.584601][   T10] em28xx 6-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  100.587459][   T10] em28xx 6-1:0.132: board has no eeprom
[  100.599615][ T6430] em28xx 7-1:0.132: Config register raw data: 0xffffffed
[  100.602852][ T6430] em28xx 7-1:0.132: AC97 chip type couldn't be determined
[  100.605791][ T6430] em28xx 7-1:0.132: No AC97 audio processor
[  100.609501][ T6430] usb 7-1: Decoder not found
[  100.612297][ T6430] em28xx 7-1:0.132: failed to create media graph
[  100.614980][ T6430] em28xx 7-1:0.132: V4L2 device video103 deregistered
[  100.619412][ T6430] em28xx 7-1:0.132: Remote control support is not available for this card.
[  100.623117][   T34] em28xx 7-1:0.132: Closing input extension
[  100.628849][   T34] em28xx 7-1:0.132: Freeing device
[  100.643099][   T10] em28xx 6-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  100.645683][   T10] em28xx 6-1:0.132: analog set to bulk mode.
[  100.651884][ T6055] em28xx 6-1:0.132: Registering V4L2 extension
[  100.654023][   T10] usb 6-1: USB disconnect, device number 33
[  100.656399][   T10] em28xx 6-1:0.132: Disconnecting em28xx
[  100.662206][    T9] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[  100.723809][    T9] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  100.726706][    T9] em28xx 5-1:0.132: board has no eeprom
[  100.735943][ T6055] em28xx 6-1:0.132: Config register raw data: 0xffffffed
[  100.738387][ T6055] em28xx 6-1:0.132: AC97 chip type couldn't be determined
[  100.740615][ T6055] em28xx 6-1:0.132: No AC97 audio processor
[  100.743532][ T6055] usb 6-1: Decoder not found
[  100.745003][ T6055] em28xx 6-1:0.132: failed to create media graph
[  100.747589][ T6055] em28xx 6-1:0.132: V4L2 device video103 deregistered
[  100.750965][ T6055] em28xx 6-1:0.132: Remote control support is not available for this card.
[  100.758332][   T10] em28xx 6-1:0.132: Closing input extension
[  100.761661][   T10] em28xx 6-1:0.132: Freeing device
[  100.781883][    T9] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  100.784393][    T9] em28xx 5-1:0.132: analog set to bulk mode.
[  100.787775][ T6055] em28xx 5-1:0.132: Registering V4L2 extension
[  100.790316][    T9] usb 5-1: USB disconnect, device number 34
[  100.795699][    T9] em28xx 5-1:0.132: Disconnecting em28xx
[  100.850407][ T6055] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[  100.853149][ T6055] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[  100.855394][ T6055] em28xx 5-1:0.132: No AC97 audio processor
[  100.858040][ T6055] usb 5-1: Decoder not found
[  100.859550][ T6055] em28xx 5-1:0.132: failed to create media graph
[  100.861585][ T6055] em28xx 5-1:0.132: V4L2 device video103 deregistered
[  100.864950][ T6055] em28xx 5-1:0.132: Remote control support is not available for this card.
[  100.867656][    T9] em28xx 5-1:0.132: Closing input extension
[  100.871203][    T9] em28xx 5-1:0.132: Freeing device
[  101.012734][   T60] usb 8-1: new high-speed USB device number 34 using dummy_hcd
[  101.092046][ T6177] usb 7-1: new high-speed USB device number 38 using dummy_hcd
[  101.171933][   T60] usb 8-1: Using ep0 maxpacket: 32
[  101.174761][   T60] usb 8-1: config 0 has an invalid interface number: 132 but max is 0
[  101.177892][   T60] usb 8-1: config 0 has no interface number 0
[  101.180382][   T60] usb 8-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  101.186692][   T60] usb 8-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  101.189718][   T60] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  101.192469][   T60] usb 8-1: Product: syz
[  101.193808][   T60] usb 8-1: Manufacturer: syz
[  101.195371][   T60] usb 8-1: SerialNumber: syz
[  101.198295][   T60] usb 8-1: config 0 descriptor??
[  101.203205][ T7004] raw-gadget.0 gadget.3: fail, usb_ep_enable returned -22
[  101.207765][   T60] em28xx 8-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  101.211961][   T10] usb 6-1: new high-speed USB device number 34 using dummy_hcd
[  101.215113][   T60] em28xx 8-1:0.132: Video interface 132 found: bulk
[  101.262030][ T6177] usb 7-1: Using ep0 maxpacket: 32
[  101.267028][ T6177] usb 7-1: config 0 has an invalid interface number: 132 but max is 0
[  101.270284][ T6177] usb 7-1: config 0 has no interface number 0
[  101.273265][ T6177] usb 7-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  101.280887][ T6177] usb 7-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  101.284878][ T6177] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  101.288062][ T6177] usb 7-1: Product: syz
[  101.290029][ T6177] usb 7-1: Manufacturer: syz
[  101.292178][ T6177] usb 7-1: SerialNumber: syz
[  101.298050][ T6177] usb 7-1: config 0 descriptor??
[  101.301442][ T7010] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[  101.309300][ T6177] em28xx 7-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  101.313265][ T6177] em28xx 7-1:0.132: Video interface 132 found: bulk
[  101.351876][ T6123] usb 5-1: new high-speed USB device number 35 using dummy_hcd
[  101.381902][   T10] usb 6-1: Using ep0 maxpacket: 32
[  101.384779][   T10] usb 6-1: config 0 has an invalid interface number: 132 but max is 0
[  101.387328][   T10] usb 6-1: config 0 has no interface number 0
[  101.389215][   T10] usb 6-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  101.393906][   T10] usb 6-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  101.396687][   T10] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  101.399148][   T10] usb 6-1: Product: syz
[  101.400488][   T10] usb 6-1: Manufacturer: syz
[  101.402036][   T10] usb 6-1: SerialNumber: syz
[  101.404748][   T10] usb 6-1: config 0 descriptor??
[  101.406938][ T7013] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[  101.410839][   T10] em28xx 6-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  101.414042][   T10] em28xx 6-1:0.132: Video interface 132 found: bulk
[  101.472438][   T60] em28xx 8-1:0.132: unknown em28xx chip ID (0)
[  101.501876][ T6123] usb 5-1: Using ep0 maxpacket: 32
[  101.506610][ T6123] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[  101.510024][ T6123] usb 5-1: config 0 has no interface number 0
[  101.512114][ T6123] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  101.517142][ T6123] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  101.520543][ T6123] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  101.523247][ T6123] usb 5-1: Product: syz
[  101.524591][ T6123] usb 5-1: Manufacturer: syz
[  101.526336][ T6123] usb 5-1: SerialNumber: syz
[  101.529496][ T6123] usb 5-1: config 0 descriptor??
[  101.531644][ T7015] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[  101.537499][   T60] em28xx 8-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  101.538208][ T6123] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  101.540474][   T60] em28xx 8-1:0.132: board has no eeprom
[  101.543539][ T6123] em28xx 5-1:0.132: Video interface 132 found: bulk
[  101.572203][ T6177] em28xx 7-1:0.132: unknown em28xx chip ID (0)
[  101.621974][   T60] em28xx 8-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  101.624440][   T60] em28xx 8-1:0.132: analog set to bulk mode.
[  101.631576][   T60] usb 8-1: USB disconnect, device number 34
[  101.634787][ T1338] em28xx 8-1:0.132: Registering V4L2 extension
[  101.637513][   T60] em28xx 8-1:0.132: Disconnecting em28xx
[  101.639354][ T6177] em28xx 7-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  101.642151][ T6177] em28xx 7-1:0.132: board has no eeprom
[  101.662564][   T10] em28xx 6-1:0.132: unknown em28xx chip ID (0)
[  101.696103][ T1338] em28xx 8-1:0.132: Config register raw data: 0xffffffed
[  101.698734][ T1338] em28xx 8-1:0.132: AC97 chip type couldn't be determined
[  101.701750][ T1338] em28xx 8-1:0.132: No AC97 audio processor
[  101.701923][ T6177] em28xx 7-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  101.707777][ T6177] em28xx 7-1:0.132: analog set to bulk mode.
[  101.713728][ T1338] usb 8-1: Decoder not found
[  101.715741][ T1338] em28xx 8-1:0.132: failed to create media graph
[  101.718355][ T1338] em28xx 8-1:0.132: V4L2 device video103 deregistered
[  101.723348][ T1338] em28xx 8-1:0.132: Remote control support is not available for this card.
[  101.724063][   T10] em28xx 6-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  101.726808][   T24] em28xx 7-1:0.132: Registering V4L2 extension
[  101.729580][   T10] em28xx 6-1:0.132: board has no eeprom
[  101.741466][ T6177] usb 7-1: USB disconnect, device number 38
[  101.745491][ T6177] em28xx 7-1:0.132: Disconnecting em28xx
[  101.790853][   T24] em28xx 7-1:0.132: Config register raw data: 0xffffffed
[  101.792205][ T6123] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[  101.793342][   T24] em28xx 7-1:0.132: AC97 chip type couldn't be determined
[  101.798187][   T24] em28xx 7-1:0.132: No AC97 audio processor
[  101.801858][   T10] em28xx 6-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  101.802003][   T24] usb 7-1: Decoder not found
[  101.804306][   T10] em28xx 6-1:0.132: analog set to bulk mode.
[  101.806179][   T24] em28xx 7-1:0.132: failed to create media graph
[  101.809726][   T10] usb 6-1: USB disconnect, device number 34
[  101.810575][   T24] em28xx 7-1:0.132: V4L2 device video103 deregistered
[  101.812046][   T24] em28xx 7-1:0.132: Remote control support is not available for this card.
[  101.813071][   T10] em28xx 6-1:0.132: Disconnecting em28xx
[  101.815123][   T60] em28xx 8-1:0.132: Closing input extension
[  101.825255][    T9] em28xx 6-1:0.132: Registering V4L2 extension
[  101.827568][   T60] em28xx 8-1:0.132: Freeing device
[  101.859741][ T6123] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  101.862622][ T6123] em28xx 5-1:0.132: board has no eeprom
[  101.882111][    T9] em28xx 6-1:0.132: Config register raw data: 0xffffffed
[  101.884306][    T9] em28xx 6-1:0.132: AC97 chip type couldn't be determined
[  101.886550][    T9] em28xx 6-1:0.132: No AC97 audio processor
[  101.889118][    T9] usb 6-1: Decoder not found
[  101.890618][    T9] em28xx 6-1:0.132: failed to create media graph
[  101.892901][    T9] em28xx 6-1:0.132: V4L2 device video103 deregistered
[  101.895794][    T9] em28xx 6-1:0.132: Remote control support is not available for this card.
[  101.898547][   T10] em28xx 6-1:0.132: Closing input extension
[  101.900510][ T6177] em28xx 7-1:0.132: Closing input extension
[  101.902137][   T10] em28xx 6-1:0.132: Freeing device
[  101.903903][ T6177] em28xx 7-1:0.132: Freeing device
[  101.921925][ T6123] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  101.925227][ T6123] em28xx 5-1:0.132: analog set to bulk mode.
[  101.927890][ T6527] em28xx 5-1:0.132: Registering V4L2 extension
[  101.937483][ T6123] usb 5-1: USB disconnect, device number 35
[  101.939983][ T6123] em28xx 5-1:0.132: Disconnecting em28xx
[  101.980755][ T6527] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[  101.983172][ T6527] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[  101.985380][ T6527] em28xx 5-1:0.132: No AC97 audio processor
[  101.988089][ T6527] usb 5-1: Decoder not found
[  101.989588][ T6527] em28xx 5-1:0.132: failed to create media graph
[  101.992008][ T6527] em28xx 5-1:0.132: V4L2 device video103 deregistered
[  101.995519][ T6527] em28xx 5-1:0.132: Remote control support is not available for this card.
[  101.995744][ T7032] ==================================================================
[  101.998893][ T6123] em28xx 5-1:0.132: Closing input extension
[  102.001914][ T7032] BUG: KASAN: slab-use-after-free in v4l2_fh_init+0x27d/0x2c0
[  102.001937][ T7032] Read of size 8 at addr ffff888035870740 by task v4l_id/7032
[  102.001946][ T7032] 
[  102.001952][ T7032] CPU: 0 UID: 0 PID: 7032 Comm: v4l_id Not tainted syzkaller #0 PREEMPT(full) 
[  102.001965][ T7032] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
[  102.001972][ T7032] Call Trace:
[  102.001977][ T7032]  <TASK>
[  102.001982][ T7032]  dump_stack_lvl+0x116/0x1f0
[  102.001998][ T7032]  print_report+0xcd/0x630
[  102.002010][ T7032]  ? __virt_addr_valid+0x81/0x610
[  102.002025][ T7032]  ? __phys_addr+0xe8/0x180
[  102.002040][ T7032]  ? v4l2_fh_init+0x27d/0x2c0
[  102.002053][ T7032]  kasan_report+0xe0/0x110
[  102.002065][ T7032]  ? v4l2_fh_init+0x27d/0x2c0
[  102.002080][ T7032]  v4l2_fh_init+0x27d/0x2c0
[  102.002093][ T7032]  v4l2_fh_open+0x83/0xc0
[  102.002107][ T7032]  em28xx_v4l2_open+0x24e/0x7e0
[  102.002122][ T7032]  v4l2_open+0x225/0x490
[  102.002135][ T7032]  ? __pfx_v4l2_open+0x10/0x10
[  102.002146][ T7032]  chrdev_open+0x231/0x6a0
[  102.002160][ T7032]  ? __pfx_chrdev_open+0x10/0x10
[  102.002174][ T7032]  ? fsnotify_open_perm_and_set_mode+0x17c/0xa60
[  102.002188][ T7032]  do_dentry_open+0x982/0x1530
[  102.002200][ T7032]  ? __pfx_chrdev_open+0x10/0x10
[  102.002215][ T7032]  vfs_open+0x82/0x3f0
[  102.002229][ T7032]  path_openat+0x1de4/0x2cb0
[  102.002243][ T7032]  ? __pfx_path_openat+0x10/0x10
[  102.002257][ T7032]  do_filp_open+0x20b/0x470
[  102.002269][ T7032]  ? __pfx_do_filp_open+0x10/0x10
[  102.002285][ T7032]  ? alloc_fd+0x471/0x7d0
[  102.002298][ T7032]  do_sys_openat2+0x11b/0x1d0
[  102.002313][ T7032]  ? __pfx_do_sys_openat2+0x10/0x10
[  102.002327][ T7032]  ? find_held_lock+0x2b/0x80
[  102.002342][ T7032]  ? handle_mm_fault+0x2ab/0xd10
[  102.002360][ T7032]  __x64_sys_openat+0x174/0x210
[  102.002375][ T7032]  ? __pfx___x64_sys_openat+0x10/0x10
[  102.002391][ T7032]  ? do_user_addr_fault+0x843/0x1370
[  102.002403][ T7032]  do_syscall_64+0xcd/0x4e0
[  102.002418][ T7032]  entry_SYSCALL_64_after_hwframe+0x77/0x7f
[  102.002430][ T7032] RIP: 0033:0x7f86602a7407
[  102.002439][ T7032] Code: 48 89 fa 4c 89 df e8 38 aa 00 00 8b 93 08 03 00 00 59 5e 48 83 f8 fc 74 1a 5b c3 0f 1f 84 00 00 00 00 00 48 8b 44 24 10 0f 05 <5b> c3 0f 1f 80 00 00 00 00 83 e2 39 83 fa 08 75 de e8 23 ff ff ff
[  102.002450][ T7032] RSP: 002b:00007ffcbfbba270 EFLAGS: 00000202 ORIG_RAX: 0000000000000101
[  102.002461][ T7032] RAX: ffffffffffffffda RBX: 00007f8660a24880 RCX: 00007f86602a7407
[  102.002468][ T7032] RDX: 0000000000000000 RSI: 00007ffcbfbbaf1b RDI: ffffffffffffff9c
[  102.002475][ T7032] RBP: 0000000000000002 R08: 0000000000000000 R09: 0000000000000000
[  102.002481][ T7032] R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000000
[  102.002492][ T7032] R13: 00007ffcbfbba4c0 R14: 00007f8660b8b000 R15: 00005584a096d4d8
[  102.002501][ T7032]  </TASK>
[  102.002505][ T7032] 
[  102.095921][ T7032] Allocated by task 6527:
[  102.097321][ T7032]  kasan_save_stack+0x33/0x60
[  102.098841][ T7032]  kasan_save_track+0x14/0x30
[  102.100374][ T7032]  __kasan_kmalloc+0xaa/0xb0
[  102.101860][ T7032]  em28xx_v4l2_init+0x114/0x4080
[  102.103437][ T7032]  em28xx_init_extension+0x13a/0x200
[  102.105085][ T7032]  request_module_async+0x61/0x70
[  102.106747][ T7032]  process_one_work+0x9cc/0x1b70
[  102.108323][ T7032]  worker_thread+0x6c8/0xf10
[  102.109817][ T7032]  kthread+0x3c2/0x780
[  102.111139][ T7032]  ret_from_fork+0x56a/0x730
[  102.112619][ T7032]  ret_from_fork_asm+0x1a/0x30
[  102.114155][ T7032] 
[  102.114935][ T7032] Freed by task 6527:
[  102.116438][ T7032]  kasan_save_stack+0x33/0x60
[  102.118453][ T7032]  kasan_save_track+0x14/0x30
[  102.120447][ T7032]  kasan_save_free_info+0x3b/0x60
[  102.122190][ T7032]  __kasan_slab_free+0x60/0x70
[  102.123753][ T7032]  kfree+0x2b4/0x4d0
[  102.125014][ T7032]  em28xx_v4l2_init+0x22b5/0x4080
[  102.126659][ T7032]  em28xx_init_extension+0x13a/0x200
[  102.128333][ T7032]  request_module_async+0x61/0x70
[  102.129959][ T7032]  process_one_work+0x9cc/0x1b70
[  102.131541][ T7032]  worker_thread+0x6c8/0xf10
[  102.133033][ T7032]  kthread+0x3c2/0x780
[  102.134346][ T7032]  ret_from_fork+0x56a/0x730
[  102.135853][ T7032]  ret_from_fork_asm+0x1a/0x30
[  102.137409][ T7032] 
[  102.138202][ T7032] The buggy address belongs to the object at ffff888035870000
[  102.138202][ T7032]  which belongs to the cache kmalloc-8k of size 8192
[  102.142583][ T7032] The buggy address is located 1856 bytes inside of
[  102.142583][ T7032]  freed 8192-byte region [ffff888035870000, ffff888035872000)
[  102.146972][ T7032] 
[  102.147780][ T7032] The buggy address belongs to the physical page:
[  102.149848][ T7032] page: refcount:0 mapcount:0 mapping:0000000000000000 index:0xffff888035874000 pfn:0x35870
[  102.152966][ T7032] head: order:3 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
[  102.155644][ T7032] flags: 0xfff00000000040(head|node=0|zone=1|lastcpupid=0x7ff)
[  102.158022][ T7032] page_type: f5(slab)
[  102.159302][ T7032] raw: 00fff00000000040 ffff88801b843180 ffffea0000a94c00 0000000000000004
[  102.162036][ T7032] raw: ffff888035874000 0000000080020001 00000000f5000000 0000000000000000
[  102.164668][ T7032] head: 00fff00000000040 ffff88801b843180 ffffea0000a94c00 0000000000000004
[  102.167419][ T7032] head: ffff888035874000 0000000080020001 00000000f5000000 0000000000000000
[  102.170428][ T7032] head: 00fff00000000003 ffffea0000d61c01 00000000ffffffff 00000000ffffffff
[  102.173146][ T7032] head: ffffffffffffffff 0000000000000000 00000000ffffffff 0000000000000008
[  102.176250][ T7032] page dumped because: kasan: bad access detected
[  102.178229][ T7032] page_owner tracks the page as allocated
[  102.180045][ T7032] page last allocated via order 3, migratetype Unmovable, gfp_mask 0xd2040(__GFP_IO|__GFP_NOWARN|__GFP_NORETRY|__GFP_COMP|__GFP_NOMEMALLOC), pid 5686, tgid 5686 (dhcpcd-run-hook), ts 28980737329, free_ts 28970253110
[  102.186817][ T7032]  post_alloc_hook+0x1c0/0x230
[  102.188844][ T7032]  get_page_from_freelist+0x132b/0x38e0
[  102.191154][ T7032]  __alloc_frozen_pages_noprof+0x261/0x23f0
[  102.193027][ T7032]  alloc_pages_mpol+0x1fb/0x550
[  102.194595][ T7032]  new_slab+0x247/0x330
[  102.195945][ T7032]  ___slab_alloc+0xcf2/0x1750
[  102.197459][ T7032]  __slab_alloc.constprop.0+0x56/0xb0
[  102.199171][ T7032]  __kmalloc_cache_noprof+0xfb/0x3e0
[  102.200861][ T7032]  tomoyo_init_log+0xc8a/0x2140
[  102.202416][ T7032]  tomoyo_supervisor+0x302/0x13b0
[  102.204004][ T7032]  tomoyo_env_perm+0x191/0x200
[  102.205572][ T7032]  tomoyo_find_next_domain+0xec2/0x20b0
[  102.207894][ T7032]  tomoyo_bprm_check_security+0x12e/0x1d0
[  102.210280][ T7032]  security_bprm_check+0x1b9/0x1e0
[  102.212240][ T7032]  bprm_execve+0x81a/0x1640
[  102.213695][ T7032]  do_execveat_common.isra.0+0x4a5/0x610
[  102.215545][ T7032] page last free pid 5685 tgid 5685 stack trace:
[  102.217755][ T7032]  __free_frozen_pages+0x7d5/0x10f0
[  102.219445][ T7032]  qlist_free_all+0x4d/0x120
[  102.220977][ T7032]  kasan_quarantine_reduce+0x195/0x1e0
[  102.222722][ T7032]  __kasan_slab_alloc+0x69/0x90
[  102.224267][ T7032]  kmem_cache_alloc_noprof+0x1cb/0x3b0
[  102.226051][ T7032]  getname_flags.part.0+0x4c/0x550
[  102.227684][ T7032]  getname_flags+0x93/0xf0
[  102.229112][ T7032]  user_path_at+0x24/0x60
[  102.230516][ T7032]  user_statfs+0x9f/0x180
[  102.231909][ T7032]  __do_sys_statfs+0x89/0x100
[  102.233430][ T7032]  do_syscall_64+0xcd/0x4e0
[  102.234894][ T7032]  entry_SYSCALL_64_after_hwframe+0x77/0x7f
[  102.237222][ T7032] 
[  102.238266][ T7032] Memory state around the buggy address:
[  102.240616][ T7032]  ffff888035870600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  102.243225][ T7032]  ffff888035870680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  102.245843][ T7032] >ffff888035870700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  102.248403][ T7032]                                            ^
[  102.250379][ T7032]  ffff888035870780: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  102.252892][ T7032]  ffff888035870800: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  102.255464][ T7032] ==================================================================
[  102.259000][ T7032] Kernel panic - not syncing: KASAN: panic_on_warn set ...
[  102.261321][ T7032] CPU: 0 UID: 0 PID: 7032 Comm: v4l_id Not tainted syzkaller #0 PREEMPT(full) 
[  102.264187][ T7032] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
[  102.267551][ T7032] Call Trace:
[  102.268624][ T7032]  <TASK>
[  102.269578][ T7032]  dump_stack_lvl+0x3d/0x1f0
[  102.271112][ T7032]  vpanic+0x6e8/0x7a0
[  102.272402][ T7032]  ? __pfx_vpanic+0x10/0x10
[  102.273868][ T7032]  ? v4l2_fh_init+0x27d/0x2c0
[  102.275369][ T7032]  panic+0xca/0xd0
[  102.276912][ T7032]  ? __pfx_panic+0x10/0x10
[  102.278603][ T7032]  ? v4l2_fh_init+0x27d/0x2c0
[  102.280378][ T7032]  ? preempt_schedule_common+0x44/0xc0
[  102.282368][ T7032]  ? preempt_schedule_thunk+0x16/0x30
[  102.284079][ T7032]  ? check_panic_on_warn+0x1f/0xb0
[  102.285708][ T7032]  check_panic_on_warn+0xab/0xb0
[  102.287289][ T7032]  end_report+0x107/0x170
[  102.288673][ T7032]  kasan_report+0xee/0x110
[  102.290116][ T7032]  ? v4l2_fh_init+0x27d/0x2c0
[  102.291623][ T7032]  v4l2_fh_init+0x27d/0x2c0
[  102.293074][ T7032]  v4l2_fh_open+0x83/0xc0
[  102.294465][ T7032]  em28xx_v4l2_open+0x24e/0x7e0
[  102.296081][ T7032]  v4l2_open+0x225/0x490
[  102.297454][ T7032]  ? __pfx_v4l2_open+0x10/0x10
[  102.298990][ T7032]  chrdev_open+0x231/0x6a0
[  102.300431][ T7032]  ? __pfx_chrdev_open+0x10/0x10
[  102.302024][ T7032]  ? fsnotify_open_perm_and_set_mode+0x17c/0xa60
[  102.304029][ T7032]  do_dentry_open+0x982/0x1530
[  102.305546][ T7032]  ? __pfx_chrdev_open+0x10/0x10
[  102.307123][ T7032]  vfs_open+0x82/0x3f0
[  102.308428][ T7032]  path_openat+0x1de4/0x2cb0
[  102.309939][ T7032]  ? __pfx_path_openat+0x10/0x10
[  102.311510][ T7032]  do_filp_open+0x20b/0x470
[  102.312957][ T7032]  ? __pfx_do_filp_open+0x10/0x10
[  102.314569][ T7032]  ? alloc_fd+0x471/0x7d0
[  102.316069][ T7032]  do_sys_openat2+0x11b/0x1d0
[  102.318081][ T7032]  ? __pfx_do_sys_openat2+0x10/0x10
[  102.320284][ T7032]  ? find_held_lock+0x2b/0x80
[  102.322026][ T7032]  ? handle_mm_fault+0x2ab/0xd10
[  102.323613][ T7032]  __x64_sys_openat+0x174/0x210
[  102.325171][ T7032]  ? __pfx___x64_sys_openat+0x10/0x10
[  102.326912][ T7032]  ? do_user_addr_fault+0x843/0x1370
[  102.328586][ T7032]  do_syscall_64+0xcd/0x4e0
[  102.330044][ T7032]  entry_SYSCALL_64_after_hwframe+0x77/0x7f
[  102.331899][ T7032] RIP: 0033:0x7f86602a7407
[  102.333319][ T7032] Code: 48 89 fa 4c 89 df e8 38 aa 00 00 8b 93 08 03 00 00 59 5e 48 83 f8 fc 74 1a 5b c3 0f 1f 84 00 00 00 00 00 48 8b 44 24 10 0f 05 <5b> c3 0f 1f 80 00 00 00 00 83 e2 39 83 fa 08 75 de e8 23 ff ff ff
[  102.339439][ T7032] RSP: 002b:00007ffcbfbba270 EFLAGS: 00000202 ORIG_RAX: 0000000000000101
[  102.342038][ T7032] RAX: ffffffffffffffda RBX: 00007f8660a24880 RCX: 00007f86602a7407
[  102.344459][ T7032] RDX: 0000000000000000 RSI: 00007ffcbfbbaf1b RDI: ffffffffffffff9c
[  102.346935][ T7032] RBP: 0000000000000002 R08: 0000000000000000 R09: 0000000000000000
[  102.349390][ T7032] R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000000
[  102.351929][ T7032] R13: 00007ffcbfbba4c0 R14: 00007f8660b8b000 R15: 00005584a096d4d8
[  102.354413][ T7032]  </TASK>
[  102.355953][ T7032] Kernel Offset: disabled
[  102.357345][ T7032] Rebooting in 86400 seconds..

VM DIAGNOSIS:
14:16:39  Registers:
info registers vcpu 0

CPU#0
RAX=dffffc0000000060 RBX=00000000000003fd RCX=0000000000000000 RDX=00000000000003fd
RSI=ffffffff8564c190 RDI=ffffffff9b118120 RBP=ffffffff9b1180e0 RSP=ffffc900046df2b0
R8 =0000000000000001 R9 =000000000000001f R10=0000000000000000 R11=20666f2064616552
R12=0000000000000000 R13=0000000000000020 R14=fffffbfff3623076 R15=dffffc0000000000
RIP=ffffffff8564c1b7 RFL=00000002 [-------] CPL=0 II=0 A20=1 SMM=0 HLT=0
ES =0000 0000000000000000 ffffffff 00c00000
CS =0010 0000000000000000 ffffffff 00a09b00 DPL=0 CS64 [-RA]
SS =0018 0000000000000000 ffffffff 00c09300 DPL=0 DS   [-WA]
DS =0000 0000000000000000 ffffffff 00c00000
FS =0000 00007f8660a24880 ffffffff 00c00000
GS =0000 ffff8880d66b2000 ffffffff 00c00000
LDT=0000 0000000000000000 ffffffff 00c00000
TR =0040 fffffe0000003000 00004087 00008b00 DPL=0 TSS64-busy
GDT=     fffffe0000001000 0000007f
IDT=     fffffe0000000000 00000fff
CR0=80050033 CR2=00007f86603b255a CR3=000000005635e000 CR4=00352ef0
DR0=0000000000000000 DR1=0000000000000000 DR2=0000000000000000 DR3=0000000000000000 
DR6=00000000ffff0ff0 DR7=0000000000000400
EFER=0000000000000d01
FCW=037f FSW=0000 [ST=0] FTW=00 MXCSR=00001f80
FPR0=0000000000000000 0000 FPR1=0000000000000000 0000
FPR2=0000000000000000 0000 FPR3=0000000000000000 0000
FPR4=0000000000000000 0000 FPR5=0000000000000000 0000
FPR6=0000000000000000 0000 FPR7=0000000000000000 0000
Opmask00=0000000040008000 Opmask01=0000000000220211 Opmask02=0000000000000000 Opmask03=0000000000000000
Opmask04=0000000000000000 Opmask05=0000000000000000 Opmask06=0000000000000000 Opmask07=0000000000000000
ZMM00=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000100000001
ZMM01=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000001
ZMM02=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM03=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM04=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 002d002b002b002b 002c002b00000000
ZMM05=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00000000000009f0
ZMM06=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000018
ZMM07=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f8660b4c5f0 00007f8660b4c0c0
ZMM08=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM09=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM10=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM11=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM12=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM13=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM14=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM15=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM16=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM17=0000000000000000 0000000000000000 0000000000000000 0000000000000000 41003330316f6564 69762f7665642f00 64695f6c34762f76 6564752f62696c2f
ZMM18=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM19=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM20=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM21=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM22=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM23=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM24=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM25=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM26=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM27=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM28=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM29=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM30=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM31=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
info registers vcpu 1

CPU#1
RAX=0000000000000000 RBX=ffff88806a441ea0 RCX=ffffffff81af9d91 RDX=ffff888029a4c880
RSI=ffffffff81af9d6b RDI=0000000000000005 RBP=0000000000000003 RSP=ffffc900046ef2d8
R8 =0000000000000005 R9 =0000000000000000 R10=0000000000000001 R11=0000000000000000
R12=dffffc0000000000 R13=ffffed100d4883d5 R14=0000000000000001 R15=0000000000000000
RIP=ffffffff81af9d72 RFL=00000293 [--S-A-C] CPL=0 II=0 A20=1 SMM=0 HLT=0
ES =0000 0000000000000000 ffffffff 00c00000
CS =0010 0000000000000000 ffffffff 00a09b00 DPL=0 CS64 [-RA]
SS =0018 0000000000000000 ffffffff 00c09300 DPL=0 DS   [-WA]
DS =0000 0000000000000000 ffffffff 00c00000
FS =0000 0000000000000000 ffffffff 00c00000
GS =0000 ffff8880d67b2000 ffffffff 00c00000
LDT=0000 0000000000000000 ffffffff 00c00000
TR =0040 fffffe000004a000 00004087 00008b00 DPL=0 TSS64-busy
GDT=     fffffe0000048000 0000007f
IDT=     fffffe0000000000 00000fff
CR0=80050033 CR2=00005584a096e024 CR3=000000002aa64000 CR4=00352ef0
DR0=0000000000000000 DR1=0000000000000000 DR2=0000000000000000 DR3=0000000000000000 
DR6=00000000ffff0ff0 DR7=0000000000000400
EFER=0000000000000d01
FCW=037f FSW=0000 [ST=0] FTW=00 MXCSR=00001f80
FPR0=0000000000000000 0000 FPR1=0000000000000000 0000
FPR2=0000000000000000 0000 FPR3=0000000000000000 0000
FPR4=0000000000000000 0000 FPR5=0000000000000000 0000
FPR6=0000000000000000 0000 FPR7=0000000000000000 0000
Opmask00=0000000000008001 Opmask01=0000000000000fff Opmask02=00000000ffffffef Opmask03=0000000000000000
Opmask04=0000000000000000 Opmask05=0000000000000000 Opmask06=0000000000000000 Opmask07=0000000000000000
ZMM00=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM01=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM02=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007fff96f893b6
ZMM03=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007fff96f893b6 00007fff96f893bc
ZMM04=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f8593a12e6e
ZMM05=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f8593a12e7b
ZMM06=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f8593a12e75
ZMM07=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f8593a12e89
ZMM08=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f8593a12f0f
ZMM09=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f8593a12fed
ZMM10=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM11=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM12=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM13=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM14=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM15=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM16=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM17=0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f8593ba74a8 00007f8593ba74a0 00007f8593ba7498 00007f8593ba7470
ZMM18=0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f859470d100 00007f8593ba7460 00007f8593ba7478 00007f8593ba74c0
ZMM19=0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f8593ba74b8 00007f8593ba74b0 00007f8593ba74a8 00007f8593ba74a0
ZMM20=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM21=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM22=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM23=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM24=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM25=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM26=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM27=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM28=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM29=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM30=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM31=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
info registers vcpu 2

CPU#2
RAX=0000000000000000 RBX=ffff88806a441e80 RCX=ffffffff81af9d91 RDX=ffff888022658000
RSI=ffffffff81af9d6b RDI=0000000000000005 RBP=0000000000000003 RSP=ffffc90000a5f888
R8 =0000000000000005 R9 =0000000000000000 R10=0000000000000001 R11=0000000000000000
R12=dffffc0000000000 R13=ffffed100d4883d1 R14=0000000000000001 R15=0000000000000000
RIP=ffffffff81af9d72 RFL=00000293 [--S-A-C] CPL=0 II=0 A20=1 SMM=0 HLT=0
ES =0000 0000000000000000 ffffffff 00c00000
CS =0010 0000000000000000 ffffffff 00a09b00 DPL=0 CS64 [-RA]
SS =0018 0000000000000000 ffffffff 00c09300 DPL=0 DS   [-WA]
DS =0000 0000000000000000 ffffffff 00c00000
FS =0000 0000000000000000 ffffffff 00c00000
GS =0000 ffff8880d68b2000 ffffffff 00c00000
LDT=0000 0000000000000000 ffffffff 00c00000
TR =0040 fffffe0000091000 00004087 00008b00 DPL=0 TSS64-busy
GDT=     fffffe000008f000 0000007f
IDT=     fffffe0000000000 00000fff
CR0=80050033 CR2=00007fa563e1b6b0 CR3=000000000e380000 CR4=00352ef0
DR0=0000000000000000 DR1=0000000000000000 DR2=0000000000000000 DR3=0000000000000000 
DR6=00000000ffff0ff0 DR7=0000000000000400
EFER=0000000000000d01
FCW=037f FSW=0000 [ST=0] FTW=00 MXCSR=00001f80
FPR0=0000000000000000 0000 FPR1=0000000000000000 0000
FPR2=0000000000000000 0000 FPR3=0000000000000000 0000
FPR4=0000000000000000 0000 FPR5=0000000000000000 0000
FPR6=0000000000000000 0000 FPR7=0000000000000000 0000
Opmask00=000000000534c002 Opmask01=0000000000000000 Opmask02=00000000f0000000 Opmask03=0000000000000000
Opmask04=0000000000000000 Opmask05=0000000000000000 Opmask06=0000000000000000 Opmask07=0000000000000000
ZMM00=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 000055b8e7077600 000055b8e7077600
ZMM01=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007ffdbbfd7500 0000003000000010
ZMM02=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM03=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM04=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM05=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM06=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM07=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM08=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM09=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM10=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM11=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM12=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM13=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM14=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM15=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM16=0000000000000000 0000000000000000 0000000000000000 0000000000000000 2525252525252525 2525252525252525 2525252525252525 2525252525252525
ZMM17=0000000000000000 0000000000000000 0000000000000000 0000000000000000 6f6c737973007325 2e73250064252e73 2500656c6f736e6f 632f7665642f000a
ZMM18=0000000000000000 0000000000000000 0000000000000000 0000000000000000 4a49565c56005600 0b56000041000b56 000040494a564b4a 460a5340410a000a
ZMM19=0000000000000000 0000000000000000 0000000000000000 0000000000000000 56203a3233312e30 3a312d3520787838 326d65205d373235 3654205b5d383030
ZMM20=0000000000000000 0000000000000000 0000000000000000 0000000000000000 79726f7463657269 6420726f20656c69 662068637573206f 4e203a64656c6961
ZMM21=0000000000000000 0000000000000000 0000000000000000 0000000000000000 6620303d64696720 2c303d646975206f 74203932302f3530 302f6273752f7375
ZMM22=0000000000000000 0000000000000000 0000000000000000 0000000000000000 622f7665642f2066 6f2072656e776f20 676e697474657320 3a5d353739355b64
ZMM23=0000000000000000 0000000000000000 0000000000000000 0000000000000000 76656475205d3537 393554205b5d3330 323334312e353920 20205b203a6c656e
ZMM24=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM25=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM26=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM27=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM28=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM29=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM30=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM31=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
info registers vcpu 3

CPU#3
RAX=000000000011fb85 RBX=0000000000000003 RCX=ffffffff8b94cb49 RDX=0000000000000000
RSI=ffffffff8de52d29 RDI=ffffffff8c163380 RBP=ffffed1003bda000 RSP=ffffc90000197df8
R8 =0000000000000001 R9 =ffffed100d4e6655 R10=ffff88806a7332ab R11=0000000000000000
R12=0000000000000003 R13=ffff88801ded0000 R14=ffffffff90ab7590 R15=0000000000000000
RIP=ffffffff8b94b68f RFL=00000282 [--S----] CPL=0 II=0 A20=1 SMM=0 HLT=1
ES =0000 0000000000000000 ffffffff 00c00000
CS =0010 0000000000000000 ffffffff 00a09b00 DPL=0 CS64 [-RA]
SS =0018 0000000000000000 ffffffff 00c09300 DPL=0 DS   [-WA]
DS =0000 0000000000000000 ffffffff 00c00000
FS =0000 0000000000000000 ffffffff 00c00000
GS =0000 ffff8880d69b2000 ffffffff 00c00000
LDT=0000 0000000000000000 ffffffff 00c00000
TR =0040 fffffe00000d8000 00004087 00008b00 DPL=0 TSS64-busy
GDT=     fffffe00000d6000 0000007f
IDT=     fffffe0000000000 00000fff
CR0=80050033 CR2=00007f8984bf2b60 CR3=000000004f9ff000 CR4=00352ef0
DR0=0000000000000000 DR1=0000000000000000 DR2=0000000000000000 DR3=0000000000000000 
DR6=00000000ffff0ff0 DR7=0000000000000400
EFER=0000000000000d01
FCW=037f FSW=0000 [ST=0] FTW=00 MXCSR=00001f80
FPR0=0000000000000000 0000 FPR1=0000000000000000 0000
FPR2=0000000000000000 0000 FPR3=0000000000000000 0000
FPR4=0000000000000000 0000 FPR5=0000000000000000 0000
FPR6=0000000000000000 0000 FPR7=0000000000000000 0000
Opmask00=0000000080040001 Opmask01=0000000000000fff Opmask02=00000000ffffffef Opmask03=0000000000000000
Opmask04=0000000000000000 Opmask05=0000000000000000 Opmask06=0000000000000000 Opmask07=0000000000000000
ZMM00=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM01=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007fff1eab2670 0000003000000018
ZMM02=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007fff1eab27f6
ZMM03=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007fff1eab27f6 00007fff1eab27fc
ZMM04=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f4b91212e6e
ZMM05=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f4b91212e7b
ZMM06=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f4b91212e75
ZMM07=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f4b91212e89
ZMM08=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f4b91212f0f
ZMM09=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 00007f4b91212fed
ZMM10=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM11=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM12=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM13=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM14=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM15=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM16=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM17=0000000000000000 0000000000000000 0000000000000000 0000000000000000 2525252525252525 2525252525252525 2525252525252525 2525252525252525
ZMM18=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0063696e61703d73 726f727265006f72 2d746e756f6d6572 3d73726f72726500
ZMM19=0000000000000000 0000000000000000 0000000000000000 0000000000000000 00464c4b44551856 574a575740004a57 08514b504a484057 1856574a57574000
ZMM20=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM21=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM22=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM23=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM24=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM25=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM26=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM27=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM28=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM29=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM30=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000
ZMM31=0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000