Warning: Permanently added '10.128.0.143' (ED25519) to the list of known hosts.
2025/10/22 15:25:33 parsed 1 programs
[   91.102820][ T5833] cgroup: Unknown subsys name 'net'
[   91.255596][ T5833] cgroup: Unknown subsys name 'cpuset'
[   91.265775][ T5833] cgroup: Unknown subsys name 'rlimit'
[   92.065223][    T9] cfg80211: failed to load regulatory.db
[   93.066672][ T5833] Adding 124996k swap on ./swap-file.  Priority:0 extents:1 across:124996k 
[   96.615167][ T5853] soft_limit_in_bytes is deprecated and will be removed. Please report your usecase to linux-mm@kvack.org if you depend on this functionality.
[   97.101085][ T5874] Bluetooth: hci0: unexpected cc 0x0c03 length: 249 > 1
[   97.109540][ T5874] Bluetooth: hci0: unexpected cc 0x1003 length: 249 > 9
[   97.121464][ T5874] Bluetooth: hci0: unexpected cc 0x1001 length: 249 > 9
[   97.134269][ T5874] Bluetooth: hci0: unexpected cc 0x0c23 length: 249 > 4
[   97.143597][ T5874] Bluetooth: hci0: unexpected cc 0x0c38 length: 249 > 2
[   97.371928][ T5851] chnl_net:caif_netlink_parms(): no params data found
[   98.339423][ T5851] bridge0: port 1(bridge_slave_0) entered blocking state
[   98.382963][ T5851] bridge0: port 1(bridge_slave_0) entered disabled state
[   98.390382][ T5851] bridge_slave_0: entered allmulticast mode
[   98.409488][ T5851] bridge_slave_0: entered promiscuous mode
[   98.494108][ T5851] bridge0: port 2(bridge_slave_1) entered blocking state
[   98.521402][ T5851] bridge0: port 2(bridge_slave_1) entered disabled state
[   98.528718][ T5851] bridge_slave_1: entered allmulticast mode
[   98.561918][ T5851] bridge_slave_1: entered promiscuous mode
[   98.732672][ T5851] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link
[   98.774160][ T5851] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link
[   98.882206][ T5851] team0: Port device team_slave_0 added
[   98.927530][ T1153] wlan0: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[   98.930175][ T5851] team0: Port device team_slave_1 added
[   98.940281][ T1153] wlan0: Creating new IBSS network, BSSID 50:50:50:50:50:50
[   99.132159][ T5851] batman_adv: batadv0: Adding interface: batadv_slave_0
[   99.139162][ T5851] batman_adv: batadv0: The MTU of interface batadv_slave_0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1532 would solve the problem.
[   99.172371][ T5851] batman_adv: batadv0: Not using interface batadv_slave_0 (retrying later): interface not active
[   99.186365][ T5851] batman_adv: batadv0: Adding interface: batadv_slave_1
[   99.193396][ T5851] batman_adv: batadv0: The MTU of interface batadv_slave_1 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1532 would solve the problem.
[   99.219745][ T5851] batman_adv: batadv0: Not using interface batadv_slave_1 (retrying later): interface not active
[   99.259843][   T12] wlan1: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[   99.274538][   T12] wlan1: Creating new IBSS network, BSSID 50:50:50:50:50:50
[   99.403500][ T5851] hsr_slave_0: entered promiscuous mode
[   99.415738][ T5851] hsr_slave_1: entered promiscuous mode
[  100.861757][ T5851] netdevsim netdevsim2 netdevsim0: renamed from eth0
[  100.904794][ T5851] netdevsim netdevsim2 netdevsim1: renamed from eth1
[  100.936396][ T5851] netdevsim netdevsim2 netdevsim2: renamed from eth2
[  101.010257][ T5851] netdevsim netdevsim2 netdevsim3: renamed from eth3
[  101.174258][ T5851] 8021q: adding VLAN 0 to HW filter on device bond0
[  101.203496][ T5851] 8021q: adding VLAN 0 to HW filter on device team0
[  101.220986][ T1153] bridge0: port 1(bridge_slave_0) entered blocking state
[  101.228304][ T1153] bridge0: port 1(bridge_slave_0) entered forwarding state
[  101.248150][   T70] bridge0: port 2(bridge_slave_1) entered blocking state
[  101.255605][   T70] bridge0: port 2(bridge_slave_1) entered forwarding state
[  101.439516][ T5851] 8021q: adding VLAN 0 to HW filter on device batadv0
[  101.488496][ T5851] veth0_vlan: entered promiscuous mode
[  101.502824][ T5851] veth1_vlan: entered promiscuous mode
[  101.532309][ T5851] veth0_macvtap: entered promiscuous mode
[  101.542744][ T5851] veth1_macvtap: entered promiscuous mode
[  101.562180][ T5851] batman_adv: batadv0: Interface activated: batadv_slave_0
[  101.577567][ T5851] batman_adv: batadv0: Interface activated: batadv_slave_1
[  101.594645][   T70] netdevsim netdevsim2 netdevsim0: set [1, 0] type 2 family 0 port 6081 - 0
[  101.604565][   T70] netdevsim netdevsim2 netdevsim1: set [1, 0] type 2 family 0 port 6081 - 0
[  101.615897][   T70] netdevsim netdevsim2 netdevsim2: set [1, 0] type 2 family 0 port 6081 - 0
[  101.625520][   T70] netdevsim netdevsim2 netdevsim3: set [1, 0] type 2 family 0 port 6081 - 0
2025/10/22 15:25:46 executed programs: 0
[  101.846947][ T5874] Bluetooth: hci0: unexpected cc 0x0c03 length: 249 > 1
[  101.860943][ T5874] Bluetooth: hci0: unexpected cc 0x1003 length: 249 > 9
[  101.868865][ T5874] Bluetooth: hci0: unexpected cc 0x1001 length: 249 > 9
[  101.881822][ T5874] Bluetooth: hci0: unexpected cc 0x0c23 length: 249 > 4
[  101.901281][ T5874] Bluetooth: hci0: unexpected cc 0x0c38 length: 249 > 2
[  101.997477][ T5874] Bluetooth: hci1: unexpected cc 0x0c03 length: 249 > 1
[  102.028097][   T52] Bluetooth: hci1: unexpected cc 0x1003 length: 249 > 9
[  102.045858][ T5958] Bluetooth: hci2: unexpected cc 0x0c03 length: 249 > 1
[  102.063378][ T5958] Bluetooth: hci1: unexpected cc 0x1001 length: 249 > 9
[  102.065214][ T5959] Bluetooth: hci3: unexpected cc 0x0c03 length: 249 > 1
[  102.072068][ T5958] Bluetooth: hci4: unexpected cc 0x0c03 length: 249 > 1
[  102.081028][ T5959] Bluetooth: hci3: unexpected cc 0x1003 length: 249 > 9
[  102.089086][ T5958] Bluetooth: hci1: unexpected cc 0x0c23 length: 249 > 4
[  102.097035][ T5959] Bluetooth: hci3: unexpected cc 0x1001 length: 249 > 9
[  102.099709][ T5958] Bluetooth: hci2: unexpected cc 0x1003 length: 249 > 9
[  102.107477][ T5959] Bluetooth: hci3: unexpected cc 0x0c23 length: 249 > 4
[  102.116210][ T5958] Bluetooth: hci1: unexpected cc 0x0c38 length: 249 > 2
[  102.121495][ T5959] Bluetooth: hci3: unexpected cc 0x0c38 length: 249 > 2
[  102.127693][ T5958] Bluetooth: hci2: unexpected cc 0x1001 length: 249 > 9
[  102.145338][   T52] Bluetooth: hci4: unexpected cc 0x1003 length: 249 > 9
[  102.154906][   T52] Bluetooth: hci4: unexpected cc 0x1001 length: 249 > 9
[  102.156281][ T5958] Bluetooth: hci2: unexpected cc 0x0c23 length: 249 > 4
[  102.178848][   T52] Bluetooth: hci4: unexpected cc 0x0c23 length: 249 > 4
[  102.186882][   T52] Bluetooth: hci2: unexpected cc 0x0c38 length: 249 > 2
[  102.195664][ T5958] Bluetooth: hci4: unexpected cc 0x0c38 length: 249 > 2
[  102.729820][ T3481] netdevsim netdevsim2 netdevsim3 (unregistering): unset [1, 0] type 2 family 0 port 6081 - 0
[  102.839904][ T3481] netdevsim netdevsim2 netdevsim2 (unregistering): unset [1, 0] type 2 family 0 port 6081 - 0
[  102.971955][ T5948] chnl_net:caif_netlink_parms(): no params data found
[  103.128629][ T5949] chnl_net:caif_netlink_parms(): no params data found
[  103.348614][ T5948] bridge0: port 1(bridge_slave_0) entered blocking state
[  103.357668][ T5948] bridge0: port 1(bridge_slave_0) entered disabled state
[  103.366330][ T5948] bridge_slave_0: entered allmulticast mode
[  103.373875][ T5948] bridge_slave_0: entered promiscuous mode
[  103.432901][ T5948] bridge0: port 2(bridge_slave_1) entered blocking state
[  103.440121][ T5948] bridge0: port 2(bridge_slave_1) entered disabled state
[  103.448116][ T5948] bridge_slave_1: entered allmulticast mode
[  103.456347][ T5948] bridge_slave_1: entered promiscuous mode
[  103.479150][ T5951] chnl_net:caif_netlink_parms(): no params data found
[  103.499206][ T5949] bridge0: port 1(bridge_slave_0) entered blocking state
[  103.506896][ T5949] bridge0: port 1(bridge_slave_0) entered disabled state
[  103.516075][ T5949] bridge_slave_0: entered allmulticast mode
[  103.524721][ T5949] bridge_slave_0: entered promiscuous mode
[  103.534032][ T5949] bridge0: port 2(bridge_slave_1) entered blocking state
[  103.541784][ T5949] bridge0: port 2(bridge_slave_1) entered disabled state
[  103.549636][ T5949] bridge_slave_1: entered allmulticast mode
[  103.557372][ T5949] bridge_slave_1: entered promiscuous mode
[  103.617946][ T5950] chnl_net:caif_netlink_parms(): no params data found
[  103.669721][ T5948] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link
[  103.702959][ T3481] netdevsim netdevsim2 netdevsim1 (unregistering): unset [1, 0] type 2 family 0 port 6081 - 0
[  103.725734][ T5949] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link
[  103.739612][ T5949] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link
[  103.752288][ T5948] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link
[  103.783016][ T5944] chnl_net:caif_netlink_parms(): no params data found
[  103.916056][ T5949] team0: Port device team_slave_0 added
[  103.924052][ T5948] team0: Port device team_slave_0 added
[  103.960022][ T5951] bridge0: port 1(bridge_slave_0) entered blocking state
[  103.967684][ T5951] bridge0: port 1(bridge_slave_0) entered disabled state
[  103.975004][ T5951] bridge_slave_0: entered allmulticast mode
[  103.981777][ T5954] Bluetooth: hci0: command tx timeout
[  103.990084][ T5951] bridge_slave_0: entered promiscuous mode
[  104.006464][ T5949] team0: Port device team_slave_1 added
[  104.014613][ T5948] team0: Port device team_slave_1 added
[  104.060321][ T5951] bridge0: port 2(bridge_slave_1) entered blocking state
[  104.068526][ T5951] bridge0: port 2(bridge_slave_1) entered disabled state
[  104.075890][ T5951] bridge_slave_1: entered allmulticast mode
[  104.084318][ T5951] bridge_slave_1: entered promiscuous mode
[  104.128800][ T5949] batman_adv: batadv0: Adding interface: batadv_slave_0
[  104.136181][ T5949] batman_adv: batadv0: The MTU of interface batadv_slave_0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1532 would solve the problem.
[  104.162757][ T5949] batman_adv: batadv0: Not using interface batadv_slave_0 (retrying later): interface not active
[  104.219109][ T5948] batman_adv: batadv0: Adding interface: batadv_slave_0
[  104.227071][ T5954] Bluetooth: hci1: command tx timeout
[  104.230746][ T5954] Bluetooth: hci4: command tx timeout
[  104.232892][ T5948] batman_adv: batadv0: The MTU of interface batadv_slave_0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1532 would solve the problem.
[  104.238532][ T5954] Bluetooth: hci2: command tx timeout
[  104.265763][ T5948] batman_adv: batadv0: Not using interface batadv_slave_0 (retrying later): interface not active
[  104.272823][   T52] Bluetooth: hci3: command tx timeout
[  104.283651][ T5949] batman_adv: batadv0: Adding interface: batadv_slave_1
[  104.296162][ T5949] batman_adv: batadv0: The MTU of interface batadv_slave_1 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1532 would solve the problem.
[  104.323445][ T5949] batman_adv: batadv0: Not using interface batadv_slave_1 (retrying later): interface not active
[  104.335412][ T5950] bridge0: port 1(bridge_slave_0) entered blocking state
[  104.343311][ T5950] bridge0: port 1(bridge_slave_0) entered disabled state
[  104.350477][ T5950] bridge_slave_0: entered allmulticast mode
[  104.358294][ T5950] bridge_slave_0: entered promiscuous mode
[  104.382941][ T5951] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link
[  104.406044][ T5948] batman_adv: batadv0: Adding interface: batadv_slave_1
[  104.413328][ T5948] batman_adv: batadv0: The MTU of interface batadv_slave_1 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1532 would solve the problem.
[  104.439652][ T5948] batman_adv: batadv0: Not using interface batadv_slave_1 (retrying later): interface not active
[  104.465097][ T5950] bridge0: port 2(bridge_slave_1) entered blocking state
[  104.472519][ T5950] bridge0: port 2(bridge_slave_1) entered disabled state
[  104.479716][ T5950] bridge_slave_1: entered allmulticast mode
[  104.487451][ T5950] bridge_slave_1: entered promiscuous mode
[  104.509968][ T5951] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link
[  104.519849][ T5944] bridge0: port 1(bridge_slave_0) entered blocking state
[  104.527525][ T5944] bridge0: port 1(bridge_slave_0) entered disabled state
[  104.535213][ T5944] bridge_slave_0: entered allmulticast mode
[  104.543372][ T5944] bridge_slave_0: entered promiscuous mode
[  104.553528][ T5944] bridge0: port 2(bridge_slave_1) entered blocking state
[  104.561032][ T5944] bridge0: port 2(bridge_slave_1) entered disabled state
[  104.568307][ T5944] bridge_slave_1: entered allmulticast mode
[  104.576355][ T5944] bridge_slave_1: entered promiscuous mode
[  104.662281][ T5944] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link
[  104.679989][ T5950] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link
[  104.731547][ T5944] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link
[  104.745041][ T5950] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link
[  104.756539][ T5951] team0: Port device team_slave_0 added
[  104.782669][ T5949] hsr_slave_0: entered promiscuous mode
[  104.789194][ T5949] hsr_slave_1: entered promiscuous mode
[  104.796227][ T5949] debugfs: 'hsr0' already exists in 'hsr'
[  104.802500][ T5949] Cannot create hsr debugfs directory
[  104.813389][ T5948] hsr_slave_0: entered promiscuous mode
[  104.820129][ T5948] hsr_slave_1: entered promiscuous mode
[  104.826761][ T5948] debugfs: 'hsr0' already exists in 'hsr'
[  104.832828][ T5948] Cannot create hsr debugfs directory
[  104.863568][ T5951] team0: Port device team_slave_1 added
[  104.894834][ T3481] netdevsim netdevsim2 netdevsim0 (unregistering): unset [1, 0] type 2 family 0 port 6081 - 0
[  104.955390][ T5950] team0: Port device team_slave_0 added
[  104.964612][ T5950] team0: Port device team_slave_1 added
[  104.973293][ T5944] team0: Port device team_slave_0 added
[  104.979936][ T5951] batman_adv: batadv0: Adding interface: batadv_slave_0
[  104.987309][ T5951] batman_adv: batadv0: The MTU of interface batadv_slave_0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1532 would solve the problem.
[  105.013928][ T5951] batman_adv: batadv0: Not using interface batadv_slave_0 (retrying later): interface not active
[  105.071921][ T5944] team0: Port device team_slave_1 added
[  105.078954][ T5951] batman_adv: batadv0: Adding interface: batadv_slave_1
[  105.086418][ T5951] batman_adv: batadv0: The MTU of interface batadv_slave_1 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1532 would solve the problem.
[  105.113563][ T5951] batman_adv: batadv0: Not using interface batadv_slave_1 (retrying later): interface not active
[  105.205396][ T5950] batman_adv: batadv0: Adding interface: batadv_slave_0
[  105.212826][ T5950] batman_adv: batadv0: The MTU of interface batadv_slave_0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1532 would solve the problem.
[  105.239514][ T5950] batman_adv: batadv0: Not using interface batadv_slave_0 (retrying later): interface not active
[  105.253058][ T5950] batman_adv: batadv0: Adding interface: batadv_slave_1
[  105.261660][ T5950] batman_adv: batadv0: The MTU of interface batadv_slave_1 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1532 would solve the problem.
[  105.288894][ T5950] batman_adv: batadv0: Not using interface batadv_slave_1 (retrying later): interface not active
[  105.354566][ T5944] batman_adv: batadv0: Adding interface: batadv_slave_0
[  105.361912][ T5944] batman_adv: batadv0: The MTU of interface batadv_slave_0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1532 would solve the problem.
[  105.389164][ T5944] batman_adv: batadv0: Not using interface batadv_slave_0 (retrying later): interface not active
[  105.402290][ T5944] batman_adv: batadv0: Adding interface: batadv_slave_1
[  105.409361][ T5944] batman_adv: batadv0: The MTU of interface batadv_slave_1 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1532 would solve the problem.
[  105.436939][ T5944] batman_adv: batadv0: Not using interface batadv_slave_1 (retrying later): interface not active
[  105.581800][ T5951] hsr_slave_0: entered promiscuous mode
[  105.588274][ T5951] hsr_slave_1: entered promiscuous mode
[  105.594801][ T5951] debugfs: 'hsr0' already exists in 'hsr'
[  105.600887][ T5951] Cannot create hsr debugfs directory
[  105.681821][ T5950] hsr_slave_0: entered promiscuous mode
[  105.688254][ T5950] hsr_slave_1: entered promiscuous mode
[  105.694754][ T5950] debugfs: 'hsr0' already exists in 'hsr'
[  105.700632][ T5950] Cannot create hsr debugfs directory
[  105.853593][ T5944] hsr_slave_0: entered promiscuous mode
[  105.860199][ T5944] hsr_slave_1: entered promiscuous mode
[  105.867640][ T5944] debugfs: 'hsr0' already exists in 'hsr'
[  105.874071][ T5944] Cannot create hsr debugfs directory
[  105.882214][ T3481] bridge_slave_1: left allmulticast mode
[  105.888156][ T3481] bridge_slave_1: left promiscuous mode
[  105.895161][ T3481] bridge0: port 2(bridge_slave_1) entered disabled state
[  105.906388][ T3481] bridge_slave_0: left allmulticast mode
[  105.913269][ T3481] bridge_slave_0: left promiscuous mode
[  105.919098][ T3481] bridge0: port 1(bridge_slave_0) entered disabled state
[  106.060821][ T5954] Bluetooth: hci0: command tx timeout
[  106.266251][ T3481] bond0 (unregistering): (slave bond_slave_0): Releasing backup interface
[  106.278126][ T3481] bond0 (unregistering): (slave bond_slave_1): Releasing backup interface
[  106.288546][ T3481] bond0 (unregistering): Released all slaves
[  106.310886][ T5874] Bluetooth: hci3: command tx timeout
[  106.316409][ T5874] Bluetooth: hci4: command tx timeout
[  106.320686][   T52] Bluetooth: hci1: command tx timeout
[  106.322319][ T5954] Bluetooth: hci2: command tx timeout
[  106.527992][ T3481] hsr_slave_0: left promiscuous mode
[  106.534558][ T3481] hsr_slave_1: left promiscuous mode
[  106.542012][ T3481] batman_adv: batadv0: Interface deactivated: batadv_slave_0
[  106.549495][ T3481] batman_adv: batadv0: Removing interface: batadv_slave_0
[  106.559011][ T3481] batman_adv: batadv0: Interface deactivated: batadv_slave_1
[  106.566784][ T3481] batman_adv: batadv0: Removing interface: batadv_slave_1
[  106.583388][ T3481] veth1_macvtap: left promiscuous mode
[  106.589222][ T3481] veth0_macvtap: left promiscuous mode
[  106.595121][ T3481] veth1_vlan: left promiscuous mode
[  106.600721][ T3481] veth0_vlan: left promiscuous mode
[  106.930922][ T3481] team0 (unregistering): Port device team_slave_1 removed
[  106.963666][ T3481] team0 (unregistering): Port device team_slave_0 removed
[  107.683140][ T5949] netdevsim netdevsim2 netdevsim0: renamed from eth0
[  107.704884][ T5949] netdevsim netdevsim2 netdevsim1: renamed from eth1
[  107.723661][ T5949] netdevsim netdevsim2 netdevsim2: renamed from eth2
[  107.750383][ T5949] netdevsim netdevsim2 netdevsim3: renamed from eth3
[  107.885477][ T5951] netdevsim netdevsim3 netdevsim0: renamed from eth0
[  107.904982][ T5951] netdevsim netdevsim3 netdevsim1: renamed from eth1
[  107.919975][ T5951] netdevsim netdevsim3 netdevsim2: renamed from eth2
[  107.964757][ T5951] netdevsim netdevsim3 netdevsim3: renamed from eth3
[  108.083336][ T5950] netdevsim netdevsim4 netdevsim0: renamed from eth0
[  108.110207][ T5950] netdevsim netdevsim4 netdevsim1: renamed from eth1
[  108.151056][ T5954] Bluetooth: hci0: command tx timeout
[  108.157095][ T5950] netdevsim netdevsim4 netdevsim2: renamed from eth2
[  108.202210][ T5950] netdevsim netdevsim4 netdevsim3: renamed from eth3
[  108.256194][ T5948] netdevsim netdevsim1 netdevsim0: renamed from eth0
[  108.274364][ T5948] netdevsim netdevsim1 netdevsim1: renamed from eth1
[  108.311302][ T5948] netdevsim netdevsim1 netdevsim2: renamed from eth2
[  108.369494][ T5948] netdevsim netdevsim1 netdevsim3: renamed from eth3
[  108.381245][ T5954] Bluetooth: hci2: command tx timeout
[  108.381262][ T5958] Bluetooth: hci4: command tx timeout
[  108.386792][ T5954] Bluetooth: hci3: command tx timeout
[  108.393329][   T52] Bluetooth: hci1: command tx timeout
[  108.454844][ T5944] netdevsim netdevsim0 netdevsim0: renamed from eth0
[  108.475268][ T5949] 8021q: adding VLAN 0 to HW filter on device bond0
[  108.498702][ T5944] netdevsim netdevsim0 netdevsim1: renamed from eth1
[  108.519976][ T5944] netdevsim netdevsim0 netdevsim2: renamed from eth2
[  108.532453][ T5944] netdevsim netdevsim0 netdevsim3: renamed from eth3
[  108.582179][ T5951] 8021q: adding VLAN 0 to HW filter on device bond0
[  108.608959][ T5949] 8021q: adding VLAN 0 to HW filter on device team0
[  108.640072][ T3481] bridge0: port 1(bridge_slave_0) entered blocking state
[  108.647444][ T3481] bridge0: port 1(bridge_slave_0) entered forwarding state
[  108.678915][ T5951] 8021q: adding VLAN 0 to HW filter on device team0
[  108.732610][ T3481] bridge0: port 2(bridge_slave_1) entered blocking state
[  108.739892][ T3481] bridge0: port 2(bridge_slave_1) entered forwarding state
[  108.776832][ T1153] bridge0: port 1(bridge_slave_0) entered blocking state
[  108.784038][ T1153] bridge0: port 1(bridge_slave_0) entered forwarding state
[  108.824612][ T1153] bridge0: port 2(bridge_slave_1) entered blocking state
[  108.831971][ T1153] bridge0: port 2(bridge_slave_1) entered forwarding state
[  108.846932][ T5950] 8021q: adding VLAN 0 to HW filter on device bond0
[  109.003839][ T5950] 8021q: adding VLAN 0 to HW filter on device team0
[  109.037994][ T1153] bridge0: port 1(bridge_slave_0) entered blocking state
[  109.045266][ T1153] bridge0: port 1(bridge_slave_0) entered forwarding state
[  109.112289][ T5948] 8021q: adding VLAN 0 to HW filter on device bond0
[  109.143463][ T1153] bridge0: port 2(bridge_slave_1) entered blocking state
[  109.150784][ T1153] bridge0: port 2(bridge_slave_1) entered forwarding state
[  109.186590][ T5944] 8021q: adding VLAN 0 to HW filter on device bond0
[  109.228873][ T5948] 8021q: adding VLAN 0 to HW filter on device team0
[  109.298654][ T5944] 8021q: adding VLAN 0 to HW filter on device team0
[  109.327524][ T3536] bridge0: port 1(bridge_slave_0) entered blocking state
[  109.334870][ T3536] bridge0: port 1(bridge_slave_0) entered forwarding state
[  109.428091][   T12] bridge0: port 2(bridge_slave_1) entered blocking state
[  109.435383][   T12] bridge0: port 2(bridge_slave_1) entered forwarding state
[  109.492431][   T12] bridge0: port 1(bridge_slave_0) entered blocking state
[  109.499693][   T12] bridge0: port 1(bridge_slave_0) entered forwarding state
[  109.543790][ T3481] bridge0: port 2(bridge_slave_1) entered blocking state
[  109.551112][ T3481] bridge0: port 2(bridge_slave_1) entered forwarding state
[  109.716653][ T5949] 8021q: adding VLAN 0 to HW filter on device batadv0
[  109.944512][ T5949] veth0_vlan: entered promiscuous mode
[  110.000956][ T5949] veth1_vlan: entered promiscuous mode
[  110.025234][ T5951] 8021q: adding VLAN 0 to HW filter on device batadv0
[  110.177405][ T5950] 8021q: adding VLAN 0 to HW filter on device batadv0
[  110.221165][   T52] Bluetooth: hci0: command tx timeout
[  110.244037][ T5949] veth0_macvtap: entered promiscuous mode
[  110.262623][ T5949] veth1_macvtap: entered promiscuous mode
[  110.284177][ T5948] 8021q: adding VLAN 0 to HW filter on device batadv0
[  110.315438][ T5951] veth0_vlan: entered promiscuous mode
[  110.358663][ T5949] batman_adv: batadv0: Interface activated: batadv_slave_0
[  110.386989][ T5949] batman_adv: batadv0: Interface activated: batadv_slave_1
[  110.406072][ T5951] veth1_vlan: entered promiscuous mode
[  110.420144][ T5944] 8021q: adding VLAN 0 to HW filter on device batadv0
[  110.446944][   T12] netdevsim netdevsim2 netdevsim0: set [1, 0] type 2 family 0 port 6081 - 0
[  110.460238][   T12] netdevsim netdevsim2 netdevsim1: set [1, 0] type 2 family 0 port 6081 - 0
[  110.462199][   T52] Bluetooth: hci1: command tx timeout
[  110.475190][ T5958] Bluetooth: hci4: command tx timeout
[  110.475211][ T5954] Bluetooth: hci3: command tx timeout
[  110.481503][ T5958] Bluetooth: hci2: command tx timeout
[  110.504132][   T12] netdevsim netdevsim2 netdevsim2: set [1, 0] type 2 family 0 port 6081 - 0
[  110.515447][   T12] netdevsim netdevsim2 netdevsim3: set [1, 0] type 2 family 0 port 6081 - 0
[  110.581429][ T5948] veth0_vlan: entered promiscuous mode
[  110.618934][ T5951] veth0_macvtap: entered promiscuous mode
[  110.646796][ T5948] veth1_vlan: entered promiscuous mode
[  110.684470][ T5951] veth1_macvtap: entered promiscuous mode
[  110.777335][ T1153] wlan0: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[  110.785776][ T5950] veth0_vlan: entered promiscuous mode
[  110.798230][ T1153] wlan0: Creating new IBSS network, BSSID 50:50:50:50:50:50
[  110.805127][ T5944] veth0_vlan: entered promiscuous mode
[  110.819256][ T5951] batman_adv: batadv0: Interface activated: batadv_slave_0
[  110.838915][ T5950] veth1_vlan: entered promiscuous mode
[  110.867440][   T12] wlan1: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[  110.873497][ T5944] veth1_vlan: entered promiscuous mode
[  110.882968][   T12] wlan1: Creating new IBSS network, BSSID 50:50:50:50:50:50
[  110.895756][ T5948] veth0_macvtap: entered promiscuous mode
[  110.907167][ T5951] batman_adv: batadv0: Interface activated: batadv_slave_1
[  110.946189][ T5948] veth1_macvtap: entered promiscuous mode
[  110.954552][   T12] netdevsim netdevsim3 netdevsim0: set [1, 0] type 2 family 0 port 6081 - 0
[  110.982061][   T12] netdevsim netdevsim3 netdevsim1: set [1, 0] type 2 family 0 port 6081 - 0
2025/10/22 15:25:56 executed programs: 10
[  110.993339][   T12] netdevsim netdevsim3 netdevsim2: set [1, 0] type 2 family 0 port 6081 - 0
[  111.007090][ T1153] netdevsim netdevsim3 netdevsim3: set [1, 0] type 2 family 0 port 6081 - 0
[  111.116055][ T5948] batman_adv: batadv0: Interface activated: batadv_slave_0
[  111.130022][ T5948] batman_adv: batadv0: Interface activated: batadv_slave_1
[  111.158954][   T13] wlan0: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[  111.165673][ T5944] veth0_macvtap: entered promiscuous mode
[  111.169359][   T13] wlan0: Creating new IBSS network, BSSID 50:50:50:50:50:50
[  111.186110][ T5950] veth0_macvtap: entered promiscuous mode
[  111.207820][   T12] netdevsim netdevsim1 netdevsim0: set [1, 0] type 2 family 0 port 6081 - 0
[  111.217023][   T12] netdevsim netdevsim1 netdevsim1: set [1, 0] type 2 family 0 port 6081 - 0
[  111.229195][ T5950] veth1_macvtap: entered promiscuous mode
[  111.239339][ T5944] veth1_macvtap: entered promiscuous mode
[  111.256119][   T12] netdevsim netdevsim1 netdevsim2: set [1, 0] type 2 family 0 port 6081 - 0
[  111.265222][   T12] netdevsim netdevsim1 netdevsim3: set [1, 0] type 2 family 0 port 6081 - 0
[  111.291073][ T6080] usb 3-1: new high-speed USB device number 2 using dummy_hcd
[  111.293377][   T12] wlan1: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[  111.310853][   T12] wlan1: Creating new IBSS network, BSSID 50:50:50:50:50:50
[  111.397732][ T5950] batman_adv: batadv0: Interface activated: batadv_slave_0
[  111.407276][ T5944] batman_adv: batadv0: Interface activated: batadv_slave_0
[  111.462147][ T6080] usb 3-1: Using ep0 maxpacket: 32
[  111.468182][ T5944] batman_adv: batadv0: Interface activated: batadv_slave_1
[  111.473685][ T6080] usb 3-1: config 0 has an invalid interface number: 132 but max is 0
[  111.488962][   T12] wlan0: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[  111.504457][   T12] wlan0: Creating new IBSS network, BSSID 50:50:50:50:50:50
[  111.509667][ T6080] usb 3-1: config 0 has no interface number 0
[  111.516825][ T5950] batman_adv: batadv0: Interface activated: batadv_slave_1
[  111.523656][ T6080] usb 3-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  111.545155][ T1153] netdevsim netdevsim0 netdevsim0: set [1, 0] type 2 family 0 port 6081 - 0
[  111.551941][ T6080] usb 3-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  111.569152][ T1153] netdevsim netdevsim0 netdevsim1: set [1, 0] type 2 family 0 port 6081 - 0
[  111.570917][ T6080] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  111.593489][ T6080] usb 3-1: Product: syz
[  111.597796][ T6080] usb 3-1: Manufacturer: syz
[  111.607954][ T6080] usb 3-1: SerialNumber: syz
[  111.608957][ T1153] netdevsim netdevsim0 netdevsim2: set [1, 0] type 2 family 0 port 6081 - 0
[  111.622132][ T1153] netdevsim netdevsim0 netdevsim3: set [1, 0] type 2 family 0 port 6081 - 0
[  111.633039][ T6080] usb 3-1: config 0 descriptor??
[  111.641817][ T3536] wlan1: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[  111.652870][ T3536] wlan1: Creating new IBSS network, BSSID 50:50:50:50:50:50
[  111.658675][ T6081] raw-gadget.0 gadget.2: fail, usb_ep_enable returned -22
[  111.666571][ T1153] netdevsim netdevsim4 netdevsim0: set [1, 0] type 2 family 0 port 6081 - 0
[  111.697038][ T6080] em28xx 3-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  111.708696][ T6080] em28xx 3-1:0.132: Video interface 132 found: bulk
[  111.719248][ T1153] netdevsim netdevsim4 netdevsim1: set [1, 0] type 2 family 0 port 6081 - 0
[  111.730800][   T24] usb 4-1: new high-speed USB device number 2 using dummy_hcd
[  111.761109][ T1153] netdevsim netdevsim4 netdevsim2: set [1, 0] type 2 family 0 port 6081 - 0
[  111.773639][ T1153] netdevsim netdevsim4 netdevsim3: set [1, 0] type 2 family 0 port 6081 - 0
[  111.888373][ T1153] wlan0: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[  111.901096][   T24] usb 4-1: Using ep0 maxpacket: 32
[  111.918089][ T1153] wlan0: Creating new IBSS network, BSSID 50:50:50:50:50:50
[  111.918957][   T24] usb 4-1: config 0 has an invalid interface number: 132 but max is 0
[  111.944696][ T6080] em28xx 3-1:0.132: unknown em28xx chip ID (0)
[  111.962076][   T24] usb 4-1: config 0 has no interface number 0
[  111.978359][  T143] wlan0: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[  111.979503][   T24] usb 4-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  111.999483][  T143] wlan0: Creating new IBSS network, BSSID 50:50:50:50:50:50
[  112.009747][   T24] usb 4-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  112.023316][   T24] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  112.048503][ T6080] em28xx 3-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  112.064660][   T24] usb 4-1: Product: syz
[  112.080200][ T6080] em28xx 3-1:0.132: board has no eeprom
[  112.083225][ T3481] wlan1: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[  112.086217][   T24] usb 4-1: Manufacturer: syz
[  112.100325][   T24] usb 4-1: SerialNumber: syz
[  112.104016][ T1153] wlan1: Created IBSS using preconfigured BSSID 50:50:50:50:50:50
[  112.105572][ T6083] usb 2-1: new high-speed USB device number 2 using dummy_hcd
[  112.114293][ T3481] wlan1: Creating new IBSS network, BSSID 50:50:50:50:50:50
[  112.133824][ T1153] wlan1: Creating new IBSS network, BSSID 50:50:50:50:50:50
[  112.141960][   T24] usb 4-1: config 0 descriptor??
[  112.155033][ T6084] raw-gadget.1 gadget.3: fail, usb_ep_enable returned -22
[  112.180732][ T6080] em28xx 3-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  112.189047][ T6080] em28xx 3-1:0.132: analog set to bulk mode.
[  112.203402][   T24] em28xx 4-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  112.218011][ T6090] em28xx 3-1:0.132: Registering V4L2 extension
[  112.235337][ T6080] usb 3-1: USB disconnect, device number 2
[  112.250331][   T24] em28xx 4-1:0.132: Video interface 132 found: bulk
[  112.276960][ T6080] em28xx 3-1:0.132: Disconnecting em28xx
[  112.321252][ T6083] usb 2-1: Using ep0 maxpacket: 32
[  112.339476][ T6083] usb 2-1: config 0 has an invalid interface number: 132 but max is 0
[  112.379351][ T6083] usb 2-1: config 0 has no interface number 0
[  112.397637][ T6083] usb 2-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  112.427799][ T6083] usb 2-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  112.442660][ T6083] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  112.451437][   T24] em28xx 4-1:0.132: unknown em28xx chip ID (0)
[  112.477562][ T6083] usb 2-1: Product: syz
[  112.487944][ T6083] usb 2-1: Manufacturer: syz
[  112.499707][ T6083] usb 2-1: SerialNumber: syz
[  112.519114][   T24] em28xx 4-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  112.538584][   T24] em28xx 4-1:0.132: board has no eeprom
[  112.549606][ T6083] usb 2-1: config 0 descriptor??
[  112.561518][ T6086] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[  112.575521][ T6083] em28xx 2-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  112.611486][    T9] usb 5-1: new high-speed USB device number 2 using dummy_hcd
[  112.611600][ T6083] em28xx 2-1:0.132: Video interface 132 found: bulk
[  112.625174][ T5953] usb 1-1: new high-speed USB device number 2 using dummy_hcd
[  112.651233][ T6090] em28xx 3-1:0.132: Config register raw data: 0xffffffed
[  112.658500][ T6090] em28xx 3-1:0.132: AC97 chip type couldn't be determined
[  112.666385][   T24] em28xx 4-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  112.677595][   T24] em28xx 4-1:0.132: analog set to bulk mode.
[  112.696138][ T6090] em28xx 3-1:0.132: No AC97 audio processor
[  112.706806][   T24] usb 4-1: USB disconnect, device number 2
[  112.722420][   T24] em28xx 4-1:0.132: Disconnecting em28xx
[  112.728347][ T6090] usb 3-1: Decoder not found
[  112.733668][ T6090] em28xx 3-1:0.132: failed to create media graph
[  112.740238][ T6090] em28xx 3-1:0.132: V4L2 device video103 deregistered
[  112.750412][ T6090] em28xx 3-1:0.132: Remote control support is not available for this card.
[  112.761446][  T940] em28xx 4-1:0.132: Registering V4L2 extension
[  112.801506][    T9] usb 5-1: Using ep0 maxpacket: 32
[  112.809619][    T9] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[  112.825481][ T5953] usb 1-1: Using ep0 maxpacket: 32
[  112.832037][    T9] usb 5-1: config 0 has no interface number 0
[  112.838570][    T9] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  112.842277][ T6083] em28xx 2-1:0.132: unknown em28xx chip ID (0)
[  112.851367][ T5953] usb 1-1: config 0 has an invalid interface number: 132 but max is 0
[  112.866240][ T5953] usb 1-1: config 0 has no interface number 0
[  112.885131][    T9] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  112.901442][ T5953] usb 1-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  112.912164][    T9] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  112.920186][    T9] usb 5-1: Product: syz
[  112.925601][    T9] usb 5-1: Manufacturer: syz
[  112.938497][ T5953] usb 1-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  112.941202][ T6083] em28xx 2-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  112.957109][    T9] usb 5-1: SerialNumber: syz
[  112.961642][    T9] usb 5-1: config 0 descriptor??
[  112.970486][ T5953] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  112.988981][  T940] em28xx 4-1:0.132: Config register raw data: 0xffffffed
[  112.989497][ T6093] raw-gadget.0 gadget.4: fail, usb_ep_enable returned -22
[  113.002383][  T940] em28xx 4-1:0.132: AC97 chip type couldn't be determined
[  113.011317][ T6083] em28xx 2-1:0.132: board has no eeprom
[  113.015277][ T5953] usb 1-1: Product: syz
[  113.017153][  T940] em28xx 4-1:0.132: No AC97 audio processor
[  113.042164][  T940] usb 4-1: Decoder not found
[  113.042518][    T9] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  113.050675][  T940] em28xx 4-1:0.132: failed to create media graph
[  113.059732][ T5953] usb 1-1: Manufacturer: syz
[  113.065278][  T940] em28xx 4-1:0.132: V4L2 device video103 deregistered
[  113.074832][ T5953] usb 1-1: SerialNumber: syz
[  113.077705][ T5953] usb 1-1: config 0 descriptor??
[  113.086678][    T9] em28xx 5-1:0.132: Video interface 132 found: bulk
[  113.088654][  T940] em28xx 4-1:0.132: Remote control support is not available for this card.
[  113.104078][ T6083] em28xx 2-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  113.116780][ T6092] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[  113.116790][ T6083] em28xx 2-1:0.132: analog set to bulk mode.
[  113.117886][ T6080] em28xx 3-1:0.132: Closing input extension
[  113.133248][ T5953] em28xx 1-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  113.142332][ T6083] usb 2-1: USB disconnect, device number 2
[  113.147603][ T5953] em28xx 1-1:0.132: Video interface 132 found: bulk
[  113.161951][ T6083] em28xx 2-1:0.132: Disconnecting em28xx
[  113.169091][ T6090] em28xx 2-1:0.132: Registering V4L2 extension
[  113.200010][ T6080] em28xx 3-1:0.132: Freeing device
[  113.291169][    T9] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[  113.380254][    T9] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  113.410779][ T5953] em28xx 1-1:0.132: unknown em28xx chip ID (0)
[  113.431823][    T9] em28xx 5-1:0.132: board has no eeprom
[  113.459598][ T6090] em28xx 2-1:0.132: Config register raw data: 0xffffffed
[  113.467373][ T6090] em28xx 2-1:0.132: AC97 chip type couldn't be determined
[  113.477351][ T6090] em28xx 2-1:0.132: No AC97 audio processor
[  113.485118][ T6090] usb 2-1: Decoder not found
[  113.490340][ T6090] em28xx 2-1:0.132: failed to create media graph
[  113.494618][ T5953] em28xx 1-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  113.496779][ T6090] em28xx 2-1:0.132: V4L2 device video103 deregistered
[  113.511041][    T9] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  113.521225][    T9] em28xx 5-1:0.132: analog set to bulk mode.
[  113.523424][ T6090] em28xx 2-1:0.132: Remote control support is not available for this card.
[  113.532505][ T5953] em28xx 1-1:0.132: board has no eeprom
[  113.536224][ T6080] usb 3-1: new high-speed USB device number 3 using dummy_hcd
[  113.549927][    T9] usb 5-1: USB disconnect, device number 2
[  113.562886][    T9] em28xx 5-1:0.132: Disconnecting em28xx
[  113.565695][   T24] em28xx 4-1:0.132: Closing input extension
[  113.575153][ T6032] em28xx 5-1:0.132: Registering V4L2 extension
[  113.588095][   T24] em28xx 4-1:0.132: Freeing device
[  113.621393][ T5953] em28xx 1-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  113.636415][ T5953] em28xx 1-1:0.132: analog set to bulk mode.
[  113.665200][ T5953] usb 1-1: USB disconnect, device number 2
[  113.683593][ T5953] em28xx 1-1:0.132: Disconnecting em28xx
[  113.710682][ T6080] usb 3-1: Using ep0 maxpacket: 32
[  113.718029][ T6080] usb 3-1: config 0 has an invalid interface number: 132 but max is 0
[  113.730249][ T6080] usb 3-1: config 0 has no interface number 0
[  113.761573][ T6080] usb 3-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  113.794360][ T6080] usb 3-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  113.814194][ T6080] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  113.842098][ T6080] usb 3-1: Product: syz
[  113.846553][ T6080] usb 3-1: Manufacturer: syz
[  113.865726][ T6080] usb 3-1: SerialNumber: syz
[  113.867945][ T6032] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[  113.886459][ T6080] usb 3-1: config 0 descriptor??
[  113.904893][ T6032] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[  113.918666][ T6097] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[  113.926191][ T6032] em28xx 5-1:0.132: No AC97 audio processor
[  113.926395][   T24] usb 4-1: new high-speed USB device number 3 using dummy_hcd
[  113.955803][ T6080] em28xx 3-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  113.968733][ T6080] em28xx 3-1:0.132: Video interface 132 found: bulk
[  113.971700][ T6032] usb 5-1: Decoder not found
[  113.982982][ T6032] em28xx 5-1:0.132: failed to create media graph
[  113.989465][ T6032] em28xx 5-1:0.132: V4L2 device video103 deregistered
[  113.998740][ T6032] em28xx 5-1:0.132: Remote control support is not available for this card.
[  114.008182][    T9] em28xx 5-1:0.132: Closing input extension
[  114.016965][ T6083] em28xx 2-1:0.132: Closing input extension
[  114.021912][    T9] em28xx 5-1:0.132: Freeing device
[  114.031366][ T5830] em28xx 1-1:0.132: Registering V4L2 extension
[  114.052261][ T6083] em28xx 2-1:0.132: Freeing device
[  114.111335][   T24] usb 4-1: Using ep0 maxpacket: 32
[  114.129241][   T24] usb 4-1: config 0 has an invalid interface number: 132 but max is 0
[  114.140161][   T24] usb 4-1: config 0 has no interface number 0
[  114.151615][   T24] usb 4-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  114.169598][   T24] usb 4-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  114.189664][   T24] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  114.209042][   T24] usb 4-1: Product: syz
[  114.224942][ T6080] em28xx 3-1:0.132: unknown em28xx chip ID (0)
[  114.235434][   T24] usb 4-1: Manufacturer: syz
[  114.240086][   T24] usb 4-1: SerialNumber: syz
[  114.261539][ T5830] em28xx 1-1:0.132: Config register raw data: 0xffffffed
[  114.262012][   T24] usb 4-1: config 0 descriptor??
[  114.278291][ T5830] em28xx 1-1:0.132: AC97 chip type couldn't be determined
[  114.286393][ T5830] em28xx 1-1:0.132: No AC97 audio processor
[  114.291556][ T6103] raw-gadget.2 gadget.3: fail, usb_ep_enable returned -22
[  114.297596][ T5830] usb 1-1: Decoder not found
[  114.305243][   T24] em28xx 4-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  114.305277][   T24] em28xx 4-1:0.132: Video interface 132 found: bulk
[  114.330654][    T9] usb 5-1: new high-speed USB device number 3 using dummy_hcd
[  114.343313][ T5830] em28xx 1-1:0.132: failed to create media graph
[  114.343551][ T6080] em28xx 3-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  114.350697][ T5830] em28xx 1-1:0.132: V4L2 device video103 deregistered
[  114.369949][ T6080] em28xx 3-1:0.132: board has no eeprom
[  114.390094][ T5830] em28xx 1-1:0.132: Remote control support is not available for this card.
[  114.400434][ T5953] em28xx 1-1:0.132: Closing input extension
[  114.400873][ T6083] usb 2-1: new high-speed USB device number 3 using dummy_hcd
[  114.429375][ T5953] em28xx 1-1:0.132: Freeing device
[  114.440707][ T6080] em28xx 3-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  114.464204][ T6080] em28xx 3-1:0.132: analog set to bulk mode.
[  114.472754][ T6090] em28xx 3-1:0.132: Registering V4L2 extension
[  114.493520][    T9] usb 5-1: Using ep0 maxpacket: 32
[  114.503142][    T9] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[  114.508038][ T6080] usb 3-1: USB disconnect, device number 3
[  114.523394][ T6080] em28xx 3-1:0.132: Disconnecting em28xx
[  114.533074][    T9] usb 5-1: config 0 has no interface number 0
[  114.539332][    T9] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  114.571152][    T9] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  114.580250][    T9] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  114.581194][ T6083] usb 2-1: Using ep0 maxpacket: 32
[  114.607617][    T9] usb 5-1: Product: syz
[  114.612954][    T9] usb 5-1: Manufacturer: syz
[  114.617586][    T9] usb 5-1: SerialNumber: syz
[  114.624509][ T6083] usb 2-1: config 0 has an invalid interface number: 132 but max is 0
[  114.636450][   T24] em28xx 4-1:0.132: unknown em28xx chip ID (0)
[  114.644012][    T9] usb 5-1: config 0 descriptor??
[  114.644906][ T6114] raw-gadget.3 gadget.4: fail, usb_ep_enable returned -22
[  114.652255][    T9] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  114.668026][ T6083] usb 2-1: config 0 has no interface number 0
[  114.678226][ T6083] usb 2-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  114.688246][    T9] em28xx 5-1:0.132: Video interface 132 found: bulk
[  114.712720][ T6083] usb 2-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  114.730006][ T6083] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  114.752366][ T6083] usb 2-1: Product: syz
[  114.757786][ T6083] usb 2-1: Manufacturer: syz
[  114.763736][ T5953] usb 1-1: new high-speed USB device number 3 using dummy_hcd
[  114.767631][   T24] em28xx 4-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  114.794469][ T6083] usb 2-1: SerialNumber: syz
[  114.811276][   T24] em28xx 4-1:0.132: board has no eeprom
[  114.824155][ T6083] usb 2-1: config 0 descriptor??
[  114.830462][ T6107] raw-gadget.0 gadget.1: fail, usb_ep_enable returned -22
[  114.839727][ T6090] em28xx 3-1:0.132: Config register raw data: 0xffffffed
[  114.847216][ T6090] em28xx 3-1:0.132: AC97 chip type couldn't be determined
[  114.867005][ T6083] em28xx 2-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  114.877213][ T6090] em28xx 3-1:0.132: No AC97 audio processor
[  114.883273][ T6083] em28xx 2-1:0.132: Video interface 132 found: bulk
[  114.892969][ T6090] usb 3-1: Decoder not found
[  114.897633][ T6090] em28xx 3-1:0.132: failed to create media graph
[  114.901033][    T9] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[  114.904318][   T24] em28xx 4-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  114.918473][ T6090] em28xx 3-1:0.132: V4L2 device video103 deregistered
[  114.927189][ T6090] em28xx 3-1:0.132: Remote control support is not available for this card.
[  114.936831][   T24] em28xx 4-1:0.132: analog set to bulk mode.
[  114.940799][ T5953] usb 1-1: Using ep0 maxpacket: 32
[  114.952833][ T6085] em28xx 4-1:0.132: Registering V4L2 extension
[  114.958689][ T5953] usb 1-1: config 0 has an invalid interface number: 132 but max is 0
[  114.959655][   T24] usb 4-1: USB disconnect, device number 3
[  114.980728][ T5953] usb 1-1: config 0 has no interface number 0
[  114.989640][    T9] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  114.992402][   T24] em28xx 4-1:0.132: Disconnecting em28xx
[  115.003652][ T5953] usb 1-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  115.023462][    T9] em28xx 5-1:0.132: board has no eeprom
[  115.043269][ T5953] usb 1-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  115.061232][ T5953] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  115.075494][ T5953] usb 1-1: Product: syz
[  115.079926][ T5953] usb 1-1: Manufacturer: syz
[  115.084690][ T5953] usb 1-1: SerialNumber: syz
[  115.095169][    T9] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  115.112495][ T5953] usb 1-1: config 0 descriptor??
[  115.114269][ T6083] em28xx 2-1:0.132: unknown em28xx chip ID (0)
[  115.117689][    T9] em28xx 5-1:0.132: analog set to bulk mode.
[  115.143253][ T6115] raw-gadget.4 gadget.0: fail, usb_ep_enable returned -22
[  115.172887][ T5953] em28xx 1-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  115.185868][ T5953] em28xx 1-1:0.132: Video interface 132 found: bulk
[  115.198267][    T9] usb 5-1: USB disconnect, device number 3
[  115.208620][    T9] em28xx 5-1:0.132: Disconnecting em28xx
[  115.216169][ T6085] em28xx 4-1:0.132: Config register raw data: 0xffffffed
[  115.227951][ T6085] em28xx 4-1:0.132: AC97 chip type couldn't be determined
[  115.237394][ T6083] em28xx 2-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  115.250336][ T6083] em28xx 2-1:0.132: board has no eeprom
[  115.257612][ T6085] em28xx 4-1:0.132: No AC97 audio processor
[  115.265682][ T6085] usb 4-1: Decoder not found
[  115.270342][ T6085] em28xx 4-1:0.132: failed to create media graph
[  115.277586][ T6085] em28xx 4-1:0.132: V4L2 device video103 deregistered
[  115.286058][ T6085] em28xx 4-1:0.132: Remote control support is not available for this card.
[  115.294833][ T6080] em28xx 3-1:0.132: Closing input extension
[  115.301877][ T5830] em28xx 5-1:0.132: Registering V4L2 extension
[  115.306491][ T6080] em28xx 3-1:0.132: Freeing device
[  115.322297][ T6083] em28xx 2-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  115.330164][ T6083] em28xx 2-1:0.132: analog set to bulk mode.
[  115.384295][ T6083] usb 2-1: USB disconnect, device number 3
[  115.392109][ T6083] em28xx 2-1:0.132: Disconnecting em28xx
[  115.454569][ T5953] em28xx 1-1:0.132: unknown em28xx chip ID (0)
[  115.535018][ T5953] em28xx 1-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  115.546252][ T5953] em28xx 1-1:0.132: board has no eeprom
[  115.557335][ T5830] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[  115.564789][ T5830] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[  115.573425][ T5830] em28xx 5-1:0.132: No AC97 audio processor
[  115.599440][ T5830] usb 5-1: Decoder not found
[  115.605232][ T5830] em28xx 5-1:0.132: failed to create media graph
[  115.624829][ T5830] em28xx 5-1:0.132: V4L2 device video103 deregistered
[  115.631807][ T5953] em28xx 1-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  115.639667][ T5953] em28xx 1-1:0.132: analog set to bulk mode.
[  115.647632][ T5830] em28xx 5-1:0.132: Remote control support is not available for this card.
[  115.658966][   T24] em28xx 4-1:0.132: Closing input extension
[  115.666858][ T6080] usb 3-1: new high-speed USB device number 4 using dummy_hcd
[  115.671467][ T5953] usb 1-1: USB disconnect, device number 3
[  115.681908][ T6085] em28xx 2-1:0.132: Registering V4L2 extension
[  115.683661][ T5953] em28xx 1-1:0.132: Disconnecting em28xx
[  115.695582][   T24] em28xx 4-1:0.132: Freeing device
[  115.830659][ T6080] usb 3-1: Using ep0 maxpacket: 32
[  115.840043][ T6080] usb 3-1: config 0 has an invalid interface number: 132 but max is 0
[  115.851359][ T6080] usb 3-1: config 0 has no interface number 0
[  115.858755][ T6085] em28xx 2-1:0.132: Config register raw data: 0xffffffed
[  115.866930][ T6080] usb 3-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  115.877695][ T6085] em28xx 2-1:0.132: AC97 chip type couldn't be determined
[  115.886022][ T6085] em28xx 2-1:0.132: No AC97 audio processor
[  115.894379][ T6080] usb 3-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  115.905678][ T6085] usb 2-1: Decoder not found
[  115.910450][ T6085] em28xx 2-1:0.132: failed to create media graph
[  115.917625][ T6080] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  115.926026][ T6085] em28xx 2-1:0.132: V4L2 device video103 deregistered
[  115.932925][ T6080] usb 3-1: Product: syz
[  115.937473][ T6080] usb 3-1: Manufacturer: syz
[  115.952256][ T6085] em28xx 2-1:0.132: Remote control support is not available for this card.
[  115.965703][ T6080] usb 3-1: SerialNumber: syz
[  115.970402][ T6083] em28xx 2-1:0.132: Closing input extension
[  115.978656][ T6032] em28xx 1-1:0.132: Registering V4L2 extension
[  115.980153][ T6080] usb 3-1: config 0 descriptor??
[  116.000839][   T24] usb 4-1: new high-speed USB device number 4 using dummy_hcd
[  116.014143][ T6083] em28xx 2-1:0.132: Freeing device
[  116.022505][ T6125] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[  116.045056][ T6080] em28xx 3-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  116.059549][ T6080] em28xx 3-1:0.132: Video interface 132 found: bulk
[  116.135989][ T6032] em28xx 1-1:0.132: Config register raw data: 0xffffffed
[  116.148670][ T6032] em28xx 1-1:0.132: AC97 chip type couldn't be determined
[  116.156036][ T6032] em28xx 1-1:0.132: No AC97 audio processor
[  116.163962][ T6032] usb 1-1: Decoder not found
[  116.170955][ T6032] em28xx 1-1:0.132: failed to create media graph
[  116.175052][   T24] usb 4-1: Using ep0 maxpacket: 32
[  116.182613][ T6032] em28xx 1-1:0.132: V4L2 device video103 deregistered
[  116.184134][ T6032] em28xx 1-1:0.132: Remote control support is not available for this card.
[  116.198244][ T5953] em28xx 1-1:0.132: Closing input extension
[  116.204332][    T9] em28xx 5-1:0.132: Closing input extension
[  116.205839][   T24] usb 4-1: config 0 has an invalid interface number: 132 but max is 0
[  116.217937][ T5953] em28xx 1-1:0.132: Freeing device
[  116.220831][   T24] usb 4-1: config 0 has no interface number 0
[  116.227873][    T9] em28xx 5-1:0.132: Freeing device
[  116.233665][   T24] usb 4-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  116.263308][   T24] usb 4-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  116.283395][   T24] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  116.299072][   T24] usb 4-1: Product: syz
[  116.305493][   T24] usb 4-1: Manufacturer: syz
[  116.310142][   T24] usb 4-1: SerialNumber: syz
[  116.317287][ T6080] em28xx 3-1:0.132: unknown em28xx chip ID (0)
[  116.341396][   T24] usb 4-1: config 0 descriptor??
[  116.347163][ T6129] raw-gadget.0 gadget.3: fail, usb_ep_enable returned -22
[  116.360709][ T6083] usb 2-1: new high-speed USB device number 4 using dummy_hcd
[  116.378240][   T24] em28xx 4-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  116.399247][   T24] em28xx 4-1:0.132: Video interface 132 found: bulk
[  116.411808][ T6080] em28xx 3-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  116.426821][ T6080] em28xx 3-1:0.132: board has no eeprom
[  116.491839][ T6080] em28xx 3-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  116.500642][ T6080] em28xx 3-1:0.132: analog set to bulk mode.
[  116.507290][ T6090] em28xx 3-1:0.132: Registering V4L2 extension
[  116.535295][ T6080] usb 3-1: USB disconnect, device number 4
[  116.545599][ T6083] usb 2-1: Using ep0 maxpacket: 32
[  116.550780][ T5953] usb 1-1: new high-speed USB device number 4 using dummy_hcd
[  116.558711][    T9] usb 5-1: new high-speed USB device number 4 using dummy_hcd
[  116.568354][ T6080] em28xx 3-1:0.132: Disconnecting em28xx
[  116.596556][ T6083] usb 2-1: config 0 has an invalid interface number: 132 but max is 0
[  116.605527][ T6083] usb 2-1: config 0 has no interface number 0
[  116.611937][ T6083] usb 2-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  116.632419][ T6083] usb 2-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  116.643615][ T6083] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  116.654867][ T6083] usb 2-1: Product: syz
[  116.659667][ T6083] usb 2-1: Manufacturer: syz
[  116.669289][ T6083] usb 2-1: SerialNumber: syz
[  116.681491][   T24] em28xx 4-1:0.132: unknown em28xx chip ID (0)
[  116.695477][ T6083] usb 2-1: config 0 descriptor??
[  116.702938][ T6135] raw-gadget.3 gadget.1: fail, usb_ep_enable returned -22
[  116.724534][ T6083] em28xx 2-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  116.735863][ T6083] em28xx 2-1:0.132: Video interface 132 found: bulk
[  116.746026][ T5953] usb 1-1: Using ep0 maxpacket: 32
[  116.752871][   T24] em28xx 4-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  116.752895][    T9] usb 5-1: Using ep0 maxpacket: 32
[  116.765617][ T5953] usb 1-1: config 0 has an invalid interface number: 132 but max is 0
[  116.785827][ T5953] usb 1-1: config 0 has no interface number 0
[  116.792683][    T9] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[  116.800599][   T24] em28xx 4-1:0.132: board has no eeprom
[  116.802045][    T9] usb 5-1: config 0 has no interface number 0
[  116.807137][ T6090] em28xx 3-1:0.132: Config register raw data: 0xffffffed
[  116.813710][ T5953] usb 1-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  116.818848][    T9] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
2025/10/22 15:26:02 executed programs: 25
[  116.836377][ T6090] em28xx 3-1:0.132: AC97 chip type couldn't be determined
[  116.850200][ T5953] usb 1-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  116.855232][ T6090] em28xx 3-1:0.132: No AC97 audio processor
[  116.868881][ T6090] usb 3-1: Decoder not found
[  116.874369][ T6090] em28xx 3-1:0.132: failed to create media graph
[  116.874854][ T5953] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  116.881089][   T24] em28xx 4-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  116.898349][ T5953] usb 1-1: Product: syz
[  116.903231][ T5953] usb 1-1: Manufacturer: syz
[  116.908625][   T24] em28xx 4-1:0.132: analog set to bulk mode.
[  116.916230][ T5953] usb 1-1: SerialNumber: syz
[  116.918792][ T6090] em28xx 3-1:0.132: V4L2 device video103 deregistered
[  116.930056][    T9] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  116.940177][    T9] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  116.950051][    T9] usb 5-1: Product: syz
[  116.955286][ T6090] em28xx 3-1:0.132: Remote control support is not available for this card.
[  116.956050][    T9] usb 5-1: Manufacturer: syz
[  116.970136][ T5953] usb 1-1: config 0 descriptor??
[  116.976008][   T24] usb 4-1: USB disconnect, device number 4
[  116.980152][    T9] usb 5-1: SerialNumber: syz
[  116.982785][ T6083] em28xx 2-1:0.132: unknown em28xx chip ID (0)
[  116.989393][ T6140] raw-gadget.4 gadget.0: fail, usb_ep_enable returned -22
[  116.998034][   T24] em28xx 4-1:0.132: Disconnecting em28xx
[  117.006861][  T940] em28xx 4-1:0.132: Registering V4L2 extension
[  117.012786][ T5953] em28xx 1-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  117.029818][ T5953] em28xx 1-1:0.132: Video interface 132 found: bulk
[  117.045466][    T9] usb 5-1: config 0 descriptor??
[  117.057162][ T6132] raw-gadget.2 gadget.4: fail, usb_ep_enable returned -22
[  117.075380][    T9] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  117.075395][ T6083] em28xx 2-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  117.075425][ T6083] em28xx 2-1:0.132: board has no eeprom
[  117.085285][    T9] em28xx 5-1:0.132: Video interface 132 found: bulk
[  117.176600][ T6083] em28xx 2-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  117.201145][ T6083] em28xx 2-1:0.132: analog set to bulk mode.
[  117.220856][ T6083] usb 2-1: USB disconnect, device number 4
[  117.228277][ T6083] em28xx 2-1:0.132: Disconnecting em28xx
[  117.244924][  T940] em28xx 4-1:0.132: Config register raw data: 0xffffffed
[  117.252370][  T940] em28xx 4-1:0.132: AC97 chip type couldn't be determined
[  117.259595][  T940] em28xx 4-1:0.132: No AC97 audio processor
[  117.272189][ T5953] em28xx 1-1:0.132: unknown em28xx chip ID (0)
[  117.273085][  T940] usb 4-1: Decoder not found
[  117.284868][  T940] em28xx 4-1:0.132: failed to create media graph
[  117.294410][  T940] em28xx 4-1:0.132: V4L2 device video103 deregistered
[  117.302591][  T940] em28xx 4-1:0.132: Remote control support is not available for this card.
[  117.311289][ T6080] em28xx 3-1:0.132: Closing input extension
[  117.317256][ T6090] em28xx 2-1:0.132: Registering V4L2 extension
[  117.321677][    T9] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[  117.327648][ T6080] em28xx 3-1:0.132: Freeing device
[  117.351074][ T5953] em28xx 1-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  117.380652][ T5953] em28xx 1-1:0.132: board has no eeprom
[  117.404887][    T9] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  117.422524][    T9] em28xx 5-1:0.132: board has no eeprom
[  117.440685][ T5953] em28xx 1-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  117.472956][ T5953] em28xx 1-1:0.132: analog set to bulk mode.
[  117.497876][    T9] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  117.541454][ T5953] usb 1-1: USB disconnect, device number 4
[  117.554131][    T9] em28xx 5-1:0.132: analog set to bulk mode.
[  117.574321][ T5953] em28xx 1-1:0.132: Disconnecting em28xx
[  117.601877][    T9] usb 5-1: USB disconnect, device number 4
[  117.614880][    T9] em28xx 5-1:0.132: Disconnecting em28xx
[  117.634761][ T6090] em28xx 2-1:0.132: Config register raw data: 0xffffffed
[  117.642252][ T6080] usb 3-1: new high-speed USB device number 5 using dummy_hcd
[  117.652484][ T6090] em28xx 2-1:0.132: AC97 chip type couldn't be determined
[  117.660157][ T6090] em28xx 2-1:0.132: No AC97 audio processor
[  117.669400][ T6090] usb 2-1: Decoder not found
[  117.674115][ T6090] em28xx 2-1:0.132: failed to create media graph
[  117.680623][ T6090] em28xx 2-1:0.132: V4L2 device video103 deregistered
[  117.688786][ T6090] em28xx 2-1:0.132: Remote control support is not available for this card.
[  117.697597][   T24] em28xx 4-1:0.132: Closing input extension
[  117.705741][   T10] em28xx 1-1:0.132: Registering V4L2 extension
[  117.710496][   T24] em28xx 4-1:0.132: Freeing device
[  117.816585][ T6080] usb 3-1: Using ep0 maxpacket: 32
[  117.834348][ T6080] usb 3-1: config 0 has an invalid interface number: 132 but max is 0
[  117.853677][ T6080] usb 3-1: config 0 has no interface number 0
[  117.859960][ T6080] usb 3-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  117.879617][ T6080] usb 3-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  117.903922][ T6080] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  117.928091][ T6080] usb 3-1: Product: syz
[  117.934253][ T6080] usb 3-1: Manufacturer: syz
[  117.938903][ T6080] usb 3-1: SerialNumber: syz
[  117.962144][ T6080] usb 3-1: config 0 descriptor??
[  117.976785][ T6150] raw-gadget.0 gadget.2: fail, usb_ep_enable returned -22
[  117.997199][   T10] em28xx 1-1:0.132: Config register raw data: 0xffffffed
[  118.003897][ T6080] em28xx 3-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  118.004649][   T10] em28xx 1-1:0.132: AC97 chip type couldn't be determined
[  118.017975][ T6080] em28xx 3-1:0.132: Video interface 132 found: bulk
[  118.030501][   T10] em28xx 1-1:0.132: No AC97 audio processor
[  118.039301][   T10] usb 1-1: Decoder not found
[  118.045467][   T10] em28xx 1-1:0.132: failed to create media graph
[  118.050955][   T24] usb 4-1: new high-speed USB device number 5 using dummy_hcd
[  118.052054][   T10] em28xx 1-1:0.132: V4L2 device video103 deregistered
[  118.069490][   T10] em28xx 1-1:0.132: Remote control support is not available for this card.
[  118.079850][ T5830] em28xx 5-1:0.132: Registering V4L2 extension
[  118.201336][ T5830] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[  118.208433][ T5830] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[  118.217639][ T5830] em28xx 5-1:0.132: No AC97 audio processor
[  118.222201][   T24] usb 4-1: Using ep0 maxpacket: 32
[  118.228705][ T5830] usb 5-1: Decoder not found
[  118.228728][ T5830] em28xx 5-1:0.132: failed to create media graph
[  118.228756][ T5830] em28xx 5-1:0.132: V4L2 device video103 deregistered
[  118.230214][ T5830] em28xx 5-1:0.132: Remote control support is not available for this card.
[  118.236750][   T24] usb 4-1: config 0 has an invalid interface number: 132 but max is 0
[  118.239850][    T9] em28xx 5-1:0.132: Closing input extension
[  118.262096][   T24] usb 4-1: config 0 has no interface number 0
[  118.274510][    T9] em28xx 5-1:0.132: Freeing device
[  118.283100][ T6080] em28xx 3-1:0.132: unknown em28xx chip ID (0)
[  118.283336][ T6083] em28xx 2-1:0.132: Closing input extension
[  118.296232][   T24] usb 4-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  118.306324][ T5953] em28xx 1-1:0.132: Closing input extension
[  118.322839][   T24] usb 4-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  118.325656][ T5953] em28xx 1-1:0.132: Freeing device
[  118.334102][ T6083] em28xx 2-1:0.132: Freeing device
[  118.351623][   T24] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  118.360177][ T6080] em28xx 3-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  118.372108][ T6080] em28xx 3-1:0.132: board has no eeprom
[  118.378623][   T24] usb 4-1: Product: syz
[  118.384247][   T24] usb 4-1: Manufacturer: syz
[  118.390497][   T24] usb 4-1: SerialNumber: syz
[  118.401940][   T24] usb 4-1: config 0 descriptor??
[  118.408127][ T6154] raw-gadget.1 gadget.3: fail, usb_ep_enable returned -22
[  118.426546][   T24] em28xx 4-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  118.437997][   T24] em28xx 4-1:0.132: Video interface 132 found: bulk
[  118.446899][ T6080] em28xx 3-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  118.456196][ T6080] em28xx 3-1:0.132: analog set to bulk mode.
[  118.471985][ T6090] em28xx 3-1:0.132: Registering V4L2 extension
[  118.503544][ T6080] usb 3-1: USB disconnect, device number 5
[  118.534747][ T6080] em28xx 3-1:0.132: Disconnecting em28xx
[  118.631441][    T9] usb 5-1: new high-speed USB device number 5 using dummy_hcd
[  118.641907][ T5953] usb 1-1: new high-speed USB device number 5 using dummy_hcd
[  118.671100][   T24] em28xx 4-1:0.132: unknown em28xx chip ID (0)
[  118.690735][ T6083] usb 2-1: new high-speed USB device number 5 using dummy_hcd
[  118.707670][ T6090] em28xx 3-1:0.132: Config register raw data: 0xffffffed
[  118.719374][ T6090] em28xx 3-1:0.132: AC97 chip type couldn't be determined
[  118.751605][ T6090] em28xx 3-1:0.132: No AC97 audio processor
[  118.757774][   T24] em28xx 4-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  118.772563][ T6090] usb 3-1: Decoder not found
[  118.784463][   T24] em28xx 4-1:0.132: board has no eeprom
[  118.794573][ T6090] em28xx 3-1:0.132: failed to create media graph
[  118.807698][ T6090] em28xx 3-1:0.132: V4L2 device video103 deregistered
[  118.812803][    T9] usb 5-1: Using ep0 maxpacket: 32
[  118.820173][ T5953] usb 1-1: Using ep0 maxpacket: 32
[  118.821777][ T6090] em28xx 3-1:0.132: Remote control support is not available for this card.
[  118.833658][ T5953] usb 1-1: config 0 has an invalid interface number: 132 but max is 0
[  118.838373][ T6080] em28xx 3-1:0.132: Closing input extension
[  118.850175][ T5953] usb 1-1: config 0 has no interface number 0
[  118.861357][ T6083] usb 2-1: Using ep0 maxpacket: 32
[  118.864731][    T9] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[  118.871398][ T6080] em28xx 3-1:0.132: Freeing device
[  118.881405][ T5953] usb 1-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  118.881628][   T24] em28xx 4-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  118.892153][    T9] usb 5-1: config 0 has no interface number 0
[  118.907401][ T6083] usb 2-1: config 0 has an invalid interface number: 132 but max is 0
[  118.910495][    T9] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  118.916644][ T6083] usb 2-1: config 0 has no interface number 0
[  118.936424][ T5953] usb 1-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  118.937076][   T24] em28xx 4-1:0.132: analog set to bulk mode.
[  118.950271][ T5953] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  118.966141][ T6083] usb 2-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  118.969399][ T5953] usb 1-1: Product: syz
[  118.985105][ T5953] usb 1-1: Manufacturer: syz
[  118.985595][  T940] em28xx 4-1:0.132: Registering V4L2 extension
[  118.990168][ T5953] usb 1-1: SerialNumber: syz
[  119.003113][    T9] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  119.012806][   T24] usb 4-1: USB disconnect, device number 5
[  119.018918][    T9] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  119.033820][ T6083] usb 2-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  119.052178][   T24] em28xx 4-1:0.132: Disconnecting em28xx
[  119.058322][ T6083] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  119.060738][    T9] usb 5-1: Product: syz
[  119.071490][ T6083] usb 2-1: Product: syz
[  119.075787][ T6083] usb 2-1: Manufacturer: syz
[  119.083065][    T9] usb 5-1: Manufacturer: syz
[  119.087729][    T9] usb 5-1: SerialNumber: syz
[  119.090643][ T6083] usb 2-1: SerialNumber: syz
[  119.094183][ T5953] usb 1-1: config 0 descriptor??
[  119.127898][    T9] usb 5-1: config 0 descriptor??
[  119.131296][ T6083] usb 2-1: config 0 descriptor??
[  119.137606][ T6161] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[  119.155528][ T6158] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[  119.157331][ T5953] em28xx 1-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  119.189250][ T6083] em28xx 2-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  119.191516][ T6164] raw-gadget.4 gadget.4: fail, usb_ep_enable returned -22
[  119.227415][ T5953] em28xx 1-1:0.132: Video interface 132 found: bulk
[  119.239692][ T6083] em28xx 2-1:0.132: Video interface 132 found: bulk
[  119.243360][    T9] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  119.272522][    T9] em28xx 5-1:0.132: Video interface 132 found: bulk
[  119.310892][ T6080] usb 3-1: new high-speed USB device number 6 using dummy_hcd
[  119.366442][  T940] em28xx 4-1:0.132: Config register raw data: 0xffffffed
[  119.375538][  T940] em28xx 4-1:0.132: AC97 chip type couldn't be determined
[  119.384661][  T940] em28xx 4-1:0.132: No AC97 audio processor
[  119.394051][  T940] usb 4-1: Decoder not found
[  119.400032][  T940] em28xx 4-1:0.132: failed to create media graph
[  119.408409][  T940] em28xx 4-1:0.132: V4L2 device video103 deregistered
[  119.412044][ T5953] em28xx 1-1:0.132: unknown em28xx chip ID (0)
[  119.419037][  T940] em28xx 4-1:0.132: Remote control support is not available for this card.
[  119.431625][   T24] em28xx 4-1:0.132: Closing input extension
[  119.444255][ T6083] em28xx 2-1:0.132: unknown em28xx chip ID (0)
[  119.455901][   T24] em28xx 4-1:0.132: Freeing device
[  119.462192][ T6080] usb 3-1: Using ep0 maxpacket: 32
[  119.476377][ T6080] usb 3-1: config 0 has an invalid interface number: 132 but max is 0
[  119.488033][ T5953] em28xx 1-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  119.491998][ T6080] usb 3-1: config 0 has no interface number 0
[  119.500305][ T5953] em28xx 1-1:0.132: board has no eeprom
[  119.515896][ T6080] usb 3-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  119.522070][    T9] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[  119.535577][ T6080] usb 3-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  119.548495][ T6080] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  119.557550][ T6083] em28xx 2-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  119.569953][ T6080] usb 3-1: Product: syz
[  119.570692][ T5953] em28xx 1-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  119.574779][ T6083] em28xx 2-1:0.132: board has no eeprom
[  119.594547][ T6080] usb 3-1: Manufacturer: syz
[  119.599903][ T6080] usb 3-1: SerialNumber: syz
[  119.611436][ T5953] em28xx 1-1:0.132: analog set to bulk mode.
[  119.617843][    T9] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  119.621759][ T6080] usb 3-1: config 0 descriptor??
[  119.630643][    T9] em28xx 5-1:0.132: board has no eeprom
[  119.641543][ T5830] em28xx 1-1:0.132: Registering V4L2 extension
[  119.655502][ T5953] usb 1-1: USB disconnect, device number 5
[  119.663713][ T5953] em28xx 1-1:0.132: Disconnecting em28xx
[  119.669462][ T6175] raw-gadget.0 gadget.2: fail, usb_ep_enable returned -22
[  119.699944][ T6080] em28xx 3-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  119.709999][ T6083] em28xx 2-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  119.720610][    T9] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  119.728559][    T9] em28xx 5-1:0.132: analog set to bulk mode.
[  119.730680][ T6083] em28xx 2-1:0.132: analog set to bulk mode.
[  119.746810][ T6080] em28xx 3-1:0.132: Video interface 132 found: bulk
[  119.772537][    T9] usb 5-1: USB disconnect, device number 5
[  119.780982][    T9] em28xx 5-1:0.132: Disconnecting em28xx
[  119.790719][   T24] usb 4-1: new high-speed USB device number 6 using dummy_hcd
[  119.817534][ T5830] em28xx 1-1:0.132: Config register raw data: 0xffffffed
[  119.820318][ T6083] usb 2-1: USB disconnect, device number 5
[  119.836537][ T5830] em28xx 1-1:0.132: AC97 chip type couldn't be determined
[  119.839275][ T6083] em28xx 2-1:0.132: Disconnecting em28xx
[  119.847738][ T5830] em28xx 1-1:0.132: No AC97 audio processor
[  119.879715][ T5830] usb 1-1: Decoder not found
[  119.884778][ T5830] em28xx 1-1:0.132: failed to create media graph
[  119.910796][ T5830] em28xx 1-1:0.132: V4L2 device video103 deregistered
[  119.936034][ T5830] em28xx 1-1:0.132: Remote control support is not available for this card.
[  119.948571][ T6032] em28xx 5-1:0.132: Registering V4L2 extension
[  119.962042][ T6080] em28xx 3-1:0.132: unknown em28xx chip ID (0)
[  119.984779][   T24] usb 4-1: Using ep0 maxpacket: 32
[  119.996064][   T24] usb 4-1: config 0 has an invalid interface number: 132 but max is 0
[  120.024659][   T24] usb 4-1: config 0 has no interface number 0
[  120.040176][ T6080] em28xx 3-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  120.053317][   T24] usb 4-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  120.065852][ T6080] em28xx 3-1:0.132: board has no eeprom
[  120.075293][   T24] usb 4-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  120.088922][   T24] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  120.098466][   T24] usb 4-1: Product: syz
[  120.103136][   T24] usb 4-1: Manufacturer: syz
[  120.107979][   T24] usb 4-1: SerialNumber: syz
[  120.121403][   T24] usb 4-1: config 0 descriptor??
[  120.131341][ T6080] em28xx 3-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  120.140003][ T6179] raw-gadget.1 gadget.3: fail, usb_ep_enable returned -22
[  120.140126][ T6032] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[  120.149068][ T6080] em28xx 3-1:0.132: analog set to bulk mode.
[  120.157268][ T6032] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[  120.166021][   T24] em28xx 4-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  120.176411][ T6032] em28xx 5-1:0.132: No AC97 audio processor
[  120.186382][   T24] em28xx 4-1:0.132: Video interface 132 found: bulk
[  120.187805][ T6032] usb 5-1: Decoder not found
[  120.203162][ T6080] usb 3-1: USB disconnect, device number 6
[  120.205342][ T6032] em28xx 5-1:0.132: failed to create media graph
[  120.216131][ T6032] em28xx 5-1:0.132: V4L2 device video103 deregistered
[  120.227939][ T6032] em28xx 5-1:0.132: Remote control support is not available for this card.
[  120.232113][ T6080] em28xx 3-1:0.132: Disconnecting em28xx
[  120.239042][    T9] em28xx 5-1:0.132: Closing input extension
[  120.250094][ T6089] em28xx 2-1:0.132: Registering V4L2 extension
[  120.269887][    T9] em28xx 5-1:0.132: Freeing device
[  120.398475][ T6089] em28xx 2-1:0.132: Config register raw data: 0xffffffed
[  120.406371][ T6089] em28xx 2-1:0.132: AC97 chip type couldn't be determined
[  120.414212][ T6089] em28xx 2-1:0.132: No AC97 audio processor
[  120.424838][   T24] em28xx 4-1:0.132: unknown em28xx chip ID (0)
[  120.443158][ T6089] usb 2-1: Decoder not found
[  120.447820][ T6089] em28xx 2-1:0.132: failed to create media graph
[  120.456383][ T6089] em28xx 2-1:0.132: V4L2 device video103 deregistered
[  120.472660][ T6089] em28xx 2-1:0.132: Remote control support is not available for this card.
[  120.481839][ T6083] em28xx 2-1:0.132: Closing input extension
[  120.487789][ T5953] em28xx 1-1:0.132: Closing input extension
[  120.492674][ T6083] em28xx 2-1:0.132: Freeing device
[  120.499026][  T940] em28xx 3-1:0.132: Registering V4L2 extension
[  120.500219][ T5953] em28xx 1-1:0.132: Freeing device
[  120.514702][   T24] em28xx 4-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  120.554482][   T24] em28xx 4-1:0.132: board has no eeprom
[  120.580802][    T9] usb 5-1: new high-speed USB device number 6 using dummy_hcd
[  120.632931][   T24] em28xx 4-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  120.651002][   T24] em28xx 4-1:0.132: analog set to bulk mode.
[  120.685560][   T24] usb 4-1: USB disconnect, device number 6
[  120.714128][   T24] em28xx 4-1:0.132: Disconnecting em28xx
[  120.750705][    T9] usb 5-1: Using ep0 maxpacket: 32
[  120.765205][  T940] em28xx 3-1:0.132: Config register raw data: 0xffffffed
[  120.766722][    T9] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[  120.781119][  T940] em28xx 3-1:0.132: AC97 chip type couldn't be determined
[  120.797416][    T9] usb 5-1: config 0 has no interface number 0
[  120.798668][  T940] em28xx 3-1:0.132: No AC97 audio processor
[  120.806316][    T9] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  120.821761][ T6083] usb 2-1: new high-speed USB device number 6 using dummy_hcd
[  120.823713][    T9] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  120.829830][  T940] usb 3-1: Decoder not found
[  120.850722][    T9] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  120.854272][  T940] em28xx 3-1:0.132: failed to create media graph
[  120.858833][    T9] usb 5-1: Product: syz
[  120.867548][  T940] em28xx 3-1:0.132: V4L2 device video103 deregistered
[  120.871618][ T5953] usb 1-1: new high-speed USB device number 6 using dummy_hcd
[  120.903674][  T940] em28xx 3-1:0.132: Remote control support is not available for this card.
[  120.914945][    T9] usb 5-1: Manufacturer: syz
[  120.919603][    T9] usb 5-1: SerialNumber: syz
[  120.926769][ T6089] em28xx 4-1:0.132: Registering V4L2 extension
[  120.928812][    T9] usb 5-1: config 0 descriptor??
[  120.957092][ T6188] raw-gadget.3 gadget.4: fail, usb_ep_enable returned -22
[  121.006370][    T9] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  121.022001][ T6083] usb 2-1: Using ep0 maxpacket: 32
[  121.029614][ T6083] usb 2-1: config 0 has an invalid interface number: 132 but max is 0
[  121.041219][ T6083] usb 2-1: config 0 has no interface number 0
[  121.041840][    T9] em28xx 5-1:0.132: Video interface 132 found: bulk
[  121.048506][ T6083] usb 2-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  121.082192][ T5953] usb 1-1: Using ep0 maxpacket: 32
[  121.085532][ T6083] usb 2-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  121.089613][ T5953] usb 1-1: config 0 has an invalid interface number: 132 but max is 0
[  121.100609][ T6083] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  121.121884][ T5953] usb 1-1: config 0 has no interface number 0
[  121.128087][ T5953] usb 1-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  121.130603][ T6083] usb 2-1: Product: syz
[  121.154257][ T6083] usb 2-1: Manufacturer: syz
[  121.158993][ T6083] usb 2-1: SerialNumber: syz
[  121.165053][ T5953] usb 1-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  121.178358][ T5953] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  121.184393][ T6083] usb 2-1: config 0 descriptor??
[  121.192145][ T5953] usb 1-1: Product: syz
[  121.196886][ T5953] usb 1-1: Manufacturer: syz
[  121.206961][ T6186] raw-gadget.0 gadget.1: fail, usb_ep_enable returned -22
[  121.225519][ T5953] usb 1-1: SerialNumber: syz
[  121.230005][ T6083] em28xx 2-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  121.234639][ T5953] usb 1-1: config 0 descriptor??
[  121.245330][ T6083] em28xx 2-1:0.132: Video interface 132 found: bulk
[  121.245898][ T6185] raw-gadget.2 gadget.0: fail, usb_ep_enable returned -22
[  121.263434][    T9] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[  121.275247][ T5953] em28xx 1-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  121.280173][ T6089] em28xx 4-1:0.132: Config register raw data: 0xffffffed
[  121.288303][ T5953] em28xx 1-1:0.132: Video interface 132 found: bulk
[  121.302142][ T6089] em28xx 4-1:0.132: AC97 chip type couldn't be determined
[  121.309483][ T6089] em28xx 4-1:0.132: No AC97 audio processor
[  121.320284][ T6089] usb 4-1: Decoder not found
[  121.325117][ T6089] em28xx 4-1:0.132: failed to create media graph
[  121.331946][ T6089] em28xx 4-1:0.132: V4L2 device video103 deregistered
[  121.338280][    T9] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  121.340625][ T6089] em28xx 4-1:0.132: Remote control support is not available for this card.
[  121.351448][    T9] em28xx 5-1:0.132: board has no eeprom
[  121.359155][ T6080] em28xx 3-1:0.132: Closing input extension
[  121.368603][   T24] em28xx 4-1:0.132: Closing input extension
[  121.381547][ T6080] em28xx 3-1:0.132: Freeing device
[  121.391584][   T24] em28xx 4-1:0.132: Freeing device
[  121.421139][    T9] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  121.429741][    T9] em28xx 5-1:0.132: analog set to bulk mode.
[  121.448942][ T5830] em28xx 5-1:0.132: Registering V4L2 extension
[  121.481874][ T6083] em28xx 2-1:0.132: unknown em28xx chip ID (0)
[  121.527029][    T9] usb 5-1: USB disconnect, device number 6
[  121.543378][ T5953] em28xx 1-1:0.132: unknown em28xx chip ID (0)
[  121.560050][ T6083] em28xx 2-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  121.564107][    T9] em28xx 5-1:0.132: Disconnecting em28xx
[  121.588922][ T6083] em28xx 2-1:0.132: board has no eeprom
[  121.646565][ T5953] em28xx 1-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  121.661884][ T5953] em28xx 1-1:0.132: board has no eeprom
[  121.672337][ T6083] em28xx 2-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  121.680463][ T6083] em28xx 2-1:0.132: analog set to bulk mode.
[  121.725969][   T24] usb 4-1: new high-speed USB device number 7 using dummy_hcd
[  121.733599][ T5953] em28xx 1-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  121.733630][ T5953] em28xx 1-1:0.132: analog set to bulk mode.
[  121.744632][ T5953] usb 1-1: USB disconnect, device number 6
[  121.756350][ T6080] usb 3-1: new high-speed USB device number 7 using dummy_hcd
[  121.757031][ T5830] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[  121.793320][ T5953] em28xx 1-1:0.132: Disconnecting em28xx
[  121.807681][ T5830] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[  121.812845][ T6083] usb 2-1: USB disconnect, device number 6
[  121.815699][ T5830] em28xx 5-1:0.132: No AC97 audio processor
[  121.831622][ T5830] usb 5-1: Decoder not found
[  121.833572][ T6083] em28xx 2-1:0.132: Disconnecting em28xx
[  121.836345][ T5830] em28xx 5-1:0.132: failed to create media graph
[  121.849734][ T5830] em28xx 5-1:0.132: V4L2 device video103 deregistered
[  121.865437][ T5830] em28xx 5-1:0.132: Remote control support is not available for this card.
[  121.875598][  T940] em28xx 2-1:0.132: Registering V4L2 extension
[  121.951787][ T6080] usb 3-1: Using ep0 maxpacket: 32
[  121.957080][   T24] usb 4-1: Using ep0 maxpacket: 32
2025/10/22 15:26:07 executed programs: 38
[  122.000371][ T6080] usb 3-1: config 0 has an invalid interface number: 132 but max is 0
[  122.013786][   T24] usb 4-1: config 0 has an invalid interface number: 132 but max is 0
[  122.032386][ T6080] usb 3-1: config 0 has no interface number 0
[  122.046148][   T24] usb 4-1: config 0 has no interface number 0
[  122.059213][ T6080] usb 3-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  122.070089][  T940] em28xx 2-1:0.132: Config register raw data: 0xffffffed
[  122.077261][   T24] usb 4-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  122.088134][  T940] em28xx 2-1:0.132: AC97 chip type couldn't be determined
[  122.095908][  T940] em28xx 2-1:0.132: No AC97 audio processor
[  122.109869][   T24] usb 4-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  122.119870][   T24] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  122.128152][ T6080] usb 3-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  122.137524][  T940] usb 2-1: Decoder not found
[  122.145163][  T940] em28xx 2-1:0.132: failed to create media graph
[  122.152012][ T6080] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  122.160041][ T6080] usb 3-1: Product: syz
[  122.164333][   T24] usb 4-1: Product: syz
[  122.168555][   T24] usb 4-1: Manufacturer: syz
[  122.173762][  T940] em28xx 2-1:0.132: V4L2 device video103 deregistered
[  122.181016][   T24] usb 4-1: SerialNumber: syz
[  122.186455][  T940] em28xx 2-1:0.132: Remote control support is not available for this card.
[  122.196655][ T6080] usb 3-1: Manufacturer: syz
[  122.202552][   T24] usb 4-1: config 0 descriptor??
[  122.209067][ T6080] usb 3-1: SerialNumber: syz
[  122.215424][ T6200] raw-gadget.4 gadget.3: fail, usb_ep_enable returned -22
[  122.217330][ T6083] em28xx 2-1:0.132: Closing input extension
[  122.231933][ T6080] usb 3-1: config 0 descriptor??
[  122.237753][ T6194] raw-gadget.1 gadget.2: fail, usb_ep_enable returned -22
[  122.247141][ T6032] em28xx 1-1:0.132: Registering V4L2 extension
[  122.251637][   T24] em28xx 4-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  122.267639][ T6080] em28xx 3-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  122.279361][ T6083] em28xx 2-1:0.132: Freeing device
[  122.294501][ T6080] em28xx 3-1:0.132: Video interface 132 found: bulk
[  122.302914][   T24] em28xx 4-1:0.132: Video interface 132 found: bulk
[  122.380258][ T6032] em28xx 1-1:0.132: Config register raw data: 0xffffffed
[  122.387998][ T6032] em28xx 1-1:0.132: AC97 chip type couldn't be determined
[  122.395401][ T6032] em28xx 1-1:0.132: No AC97 audio processor
[  122.404872][ T6032] usb 1-1: Decoder not found
[  122.409541][ T6032] em28xx 1-1:0.132: failed to create media graph
[  122.420622][ T6032] em28xx 1-1:0.132: V4L2 device video103 deregistered
[  122.429133][ T6032] em28xx 1-1:0.132: Remote control support is not available for this card.
[  122.440002][ T5953] em28xx 1-1:0.132: Closing input extension
[  122.450074][    T9] em28xx 5-1:0.132: Closing input extension
[  122.464963][ T5953] em28xx 1-1:0.132: Freeing device
[  122.474166][    T9] em28xx 5-1:0.132: Freeing device
[  122.501282][   T24] em28xx 4-1:0.132: unknown em28xx chip ID (0)
[  122.509455][ T6080] em28xx 3-1:0.132: unknown em28xx chip ID (0)
[  122.590976][   T24] em28xx 4-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  122.599992][ T6080] em28xx 3-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  122.609064][ T6083] usb 2-1: new high-speed USB device number 7 using dummy_hcd
[  122.624737][   T24] em28xx 4-1:0.132: board has no eeprom
[  122.631211][ T6080] em28xx 3-1:0.132: board has no eeprom
[  122.702397][   T24] em28xx 4-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  122.710471][ T6080] em28xx 3-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  122.720914][   T24] em28xx 4-1:0.132: analog set to bulk mode.
[  122.727046][  T940] em28xx 4-1:0.132: Registering V4L2 extension
[  122.734665][ T6080] em28xx 3-1:0.132: analog set to bulk mode.
[  122.746154][   T24] usb 4-1: USB disconnect, device number 7
[  122.762382][ T6080] usb 3-1: USB disconnect, device number 7
[  122.770339][   T24] em28xx 4-1:0.132: Disconnecting em28xx
[  122.799680][ T6080] em28xx 3-1:0.132: Disconnecting em28xx
[  122.805802][ T6083] usb 2-1: Using ep0 maxpacket: 32
[  122.811004][    T9] usb 5-1: new high-speed USB device number 7 using dummy_hcd
[  122.811469][ T5953] usb 1-1: new high-speed USB device number 7 using dummy_hcd
[  122.823729][ T6083] usb 2-1: config 0 has an invalid interface number: 132 but max is 0
[  122.834755][ T6083] usb 2-1: config 0 has no interface number 0
[  122.841731][ T6083] usb 2-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  122.855748][ T6083] usb 2-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  122.865426][ T6083] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  122.873704][ T6083] usb 2-1: Product: syz
[  122.878209][ T6083] usb 2-1: Manufacturer: syz
[  122.882968][ T6083] usb 2-1: SerialNumber: syz
[  122.891903][ T6083] usb 2-1: config 0 descriptor??
[  122.898157][ T6217] raw-gadget.2 gadget.1: fail, usb_ep_enable returned -22
[  122.915314][ T6083] em28xx 2-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  122.927415][ T6083] em28xx 2-1:0.132: Video interface 132 found: bulk
[  122.955252][  T940] em28xx 4-1:0.132: Config register raw data: 0xffffffed
[  122.972717][  T940] em28xx 4-1:0.132: AC97 chip type couldn't be determined
[  122.972857][    T9] usb 5-1: Using ep0 maxpacket: 32
[  122.980688][  T940] em28xx 4-1:0.132: No AC97 audio processor
[  123.009706][    T9] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[  123.019308][ T5953] usb 1-1: Using ep0 maxpacket: 32
[  123.022781][  T940] usb 4-1: Decoder not found
[  123.044672][    T9] usb 5-1: config 0 has no interface number 0
[  123.052915][ T5953] usb 1-1: config 0 has an invalid interface number: 132 but max is 0
[  123.053023][  T940] em28xx 4-1:0.132: failed to create media graph
[  123.061870][    T9] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  123.078127][ T5953] usb 1-1: config 0 has no interface number 0
[  123.084903][ T5953] usb 1-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  123.099233][  T940] em28xx 4-1:0.132: V4L2 device video103 deregistered
[  123.099547][ T5953] usb 1-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  123.108999][  T940] em28xx 4-1:0.132: Remote control support is not available for this card.
[  123.132851][ T6090] em28xx 3-1:0.132: Registering V4L2 extension
[  123.141666][ T5953] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  123.149925][    T9] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  123.159852][    T9] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  123.168468][ T5953] usb 1-1: Product: syz
[  123.173306][ T5953] usb 1-1: Manufacturer: syz
[  123.177984][ T5953] usb 1-1: SerialNumber: syz
[  123.183028][ T6083] em28xx 2-1:0.132: unknown em28xx chip ID (0)
[  123.189944][    T9] usb 5-1: Product: syz
[  123.194866][    T9] usb 5-1: Manufacturer: syz
[  123.199670][    T9] usb 5-1: SerialNumber: syz
[  123.208163][ T5953] usb 1-1: config 0 descriptor??
[  123.221924][ T6218] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[  123.232857][    T9] usb 5-1: config 0 descriptor??
[  123.239630][ T6213] raw-gadget.0 gadget.4: fail, usb_ep_enable returned -22
[  123.248228][ T6083] em28xx 2-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  123.252218][ T5953] em28xx 1-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  123.267918][ T5953] em28xx 1-1:0.132: Video interface 132 found: bulk
[  123.267964][ T6083] em28xx 2-1:0.132: board has no eeprom
[  123.272683][    T9] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  123.291081][    T9] em28xx 5-1:0.132: Video interface 132 found: bulk
[  123.306264][ T6090] em28xx 3-1:0.132: Config register raw data: 0xffffffed
[  123.315662][ T6090] em28xx 3-1:0.132: AC97 chip type couldn't be determined
[  123.323205][ T6090] em28xx 3-1:0.132: No AC97 audio processor
[  123.336441][ T6090] usb 3-1: Decoder not found
[  123.341324][ T6083] em28xx 2-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  123.349440][ T6083] em28xx 2-1:0.132: analog set to bulk mode.
[  123.356004][ T6090] em28xx 3-1:0.132: failed to create media graph
[  123.363820][ T6090] em28xx 3-1:0.132: V4L2 device video103 deregistered
[  123.378151][ T6083] usb 2-1: USB disconnect, device number 7
[  123.387605][ T6090] em28xx 3-1:0.132: Remote control support is not available for this card.
[  123.397891][ T6083] em28xx 2-1:0.132: Disconnecting em28xx
[  123.403769][   T24] em28xx 4-1:0.132: Closing input extension
[  123.411643][   T43] em28xx 2-1:0.132: Registering V4L2 extension
[  123.432471][   T24] em28xx 4-1:0.132: Freeing device
[  123.501973][ T5953] em28xx 1-1:0.132: unknown em28xx chip ID (0)
[  123.532377][    T9] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[  123.565870][ T5953] em28xx 1-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  123.580235][ T5953] em28xx 1-1:0.132: board has no eeprom
[  123.617682][    T9] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  123.628255][   T43] em28xx 2-1:0.132: Config register raw data: 0xffffffed
[  123.636728][   T43] em28xx 2-1:0.132: AC97 chip type couldn't be determined
[  123.649166][   T43] em28xx 2-1:0.132: No AC97 audio processor
[  123.650255][    T9] em28xx 5-1:0.132: board has no eeprom
[  123.661241][ T5953] em28xx 1-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  123.669336][ T5953] em28xx 1-1:0.132: analog set to bulk mode.
[  123.688581][   T43] usb 2-1: Decoder not found
[  123.698203][   T43] em28xx 2-1:0.132: failed to create media graph
[  123.707668][   T43] em28xx 2-1:0.132: V4L2 device video103 deregistered
[  123.719352][   T43] em28xx 2-1:0.132: Remote control support is not available for this card.
[  123.728768][ T6080] em28xx 3-1:0.132: Closing input extension
[  123.729989][ T5953] usb 1-1: USB disconnect, device number 7
[  123.739097][ T6080] em28xx 3-1:0.132: Freeing device
[  123.741868][    T9] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  123.759557][ T5830] em28xx 1-1:0.132: Registering V4L2 extension
[  123.760677][   T24] usb 4-1: new high-speed USB device number 8 using dummy_hcd
[  123.767393][    T9] em28xx 5-1:0.132: analog set to bulk mode.
[  123.820160][ T5953] em28xx 1-1:0.132: Disconnecting em28xx
[  123.829429][    T9] usb 5-1: USB disconnect, device number 7
[  123.854762][    T9] em28xx 5-1:0.132: Disconnecting em28xx
[  123.960629][   T24] usb 4-1: Using ep0 maxpacket: 32
[  123.965173][ T5830] em28xx 1-1:0.132: Config register raw data: 0xffffffed
[  123.969867][   T24] usb 4-1: config 0 has an invalid interface number: 132 but max is 0
[  123.975377][ T5830] em28xx 1-1:0.132: AC97 chip type couldn't be determined
[  123.994602][ T5830] em28xx 1-1:0.132: No AC97 audio processor
[  124.011177][   T24] usb 4-1: config 0 has no interface number 0
[  124.014361][ T5830] usb 1-1: Decoder not found
[  124.025887][ T5830] em28xx 1-1:0.132: failed to create media graph
[  124.027846][   T24] usb 4-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  124.033945][ T5830] em28xx 1-1:0.132: V4L2 device video103 deregistered
[  124.079756][ T5830] em28xx 1-1:0.132: Remote control support is not available for this card.
[  124.081691][   T24] usb 4-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  124.089137][ T5953] em28xx 1-1:0.132: Closing input extension
[  124.107271][ T6083] em28xx 2-1:0.132: Closing input extension
[  124.118747][ T6032] em28xx 5-1:0.132: Registering V4L2 extension
[  124.120799][ T6080] usb 3-1: new high-speed USB device number 8 using dummy_hcd
[  124.134850][   T24] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  124.146125][   T24] usb 4-1: Product: syz
[  124.155225][ T6083] em28xx 2-1:0.132: Freeing device
[  124.157508][ T5953] em28xx 1-1:0.132: Freeing device
[  124.173476][   T24] usb 4-1: Manufacturer: syz
[  124.178138][   T24] usb 4-1: SerialNumber: syz
[  124.214685][   T24] usb 4-1: config 0 descriptor??
[  124.223015][ T6229] raw-gadget.1 gadget.3: fail, usb_ep_enable returned -22
[  124.242503][   T24] em28xx 4-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  124.258893][   T24] em28xx 4-1:0.132: Video interface 132 found: bulk
[  124.312078][ T6080] usb 3-1: Using ep0 maxpacket: 32
[  124.325660][ T6080] usb 3-1: config 0 has an invalid interface number: 132 but max is 0
[  124.335367][ T6080] usb 3-1: config 0 has no interface number 0
[  124.343237][ T6080] usb 3-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  124.358040][ T6080] usb 3-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  124.370076][ T6032] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[  124.377548][ T6080] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  124.377578][ T6080] usb 3-1: Product: syz
[  124.377605][ T6080] usb 3-1: Manufacturer: syz
[  124.377649][ T6080] usb 3-1: SerialNumber: syz
[  124.382266][ T6080] usb 3-1: config 0 descriptor??
[  124.404664][ T6032] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[  124.412716][ T6032] em28xx 5-1:0.132: No AC97 audio processor
[  124.423727][ T6032] usb 5-1: Decoder not found
[  124.428363][ T6032] em28xx 5-1:0.132: failed to create media graph
[  124.430652][ T6230] raw-gadget.4 gadget.2: fail, usb_ep_enable returned -22
[  124.435837][ T6032] em28xx 5-1:0.132: V4L2 device video103 deregistered
[  124.448968][ T6080] em28xx 3-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  124.457038][ T6032] em28xx 5-1:0.132: Remote control support is not available for this card.
[  124.466365][ T6080] em28xx 3-1:0.132: Video interface 132 found: bulk
[  124.476787][    T9] em28xx 5-1:0.132: Closing input extension
[  124.477623][ T6083] usb 2-1: new high-speed USB device number 8 using dummy_hcd
[  124.489413][    T9] em28xx 5-1:0.132: Freeing device
[  124.502221][   T24] em28xx 4-1:0.132: unknown em28xx chip ID (0)
[  124.530679][ T5953] usb 1-1: new high-speed USB device number 8 using dummy_hcd
[  124.575140][   T24] em28xx 4-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  124.586951][   T24] em28xx 4-1:0.132: board has no eeprom
[  124.655156][   T24] em28xx 4-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  124.667661][   T24] em28xx 4-1:0.132: analog set to bulk mode.
[  124.675282][ T6090] em28xx 4-1:0.132: Registering V4L2 extension
[  124.681934][ T6083] usb 2-1: Using ep0 maxpacket: 32
[  124.690131][ T6083] usb 2-1: config 0 has an invalid interface number: 132 but max is 0
[  124.691350][ T5953] usb 1-1: Using ep0 maxpacket: 32
[  124.721369][ T6080] em28xx 3-1:0.132: unknown em28xx chip ID (0)
[  124.730168][ T6083] usb 2-1: config 0 has no interface number 0
[  124.739308][ T5953] usb 1-1: config 0 has an invalid interface number: 132 but max is 0
[  124.745565][   T24] usb 4-1: USB disconnect, device number 8
[  124.761195][ T6083] usb 2-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  124.761720][ T5953] usb 1-1: config 0 has no interface number 0
[  124.774233][   T24] em28xx 4-1:0.132: Disconnecting em28xx
[  124.789319][ T6083] usb 2-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  124.793548][ T5953] usb 1-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  124.799388][ T6083] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  124.813845][ T5953] usb 1-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  124.819799][ T6083] usb 2-1: Product: syz
[  124.827959][ T5953] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  124.838153][ T6080] em28xx 3-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  124.843786][ T5953] usb 1-1: Product: syz
[  124.850302][ T6083] usb 2-1: Manufacturer: syz
[  124.853545][    T9] usb 5-1: new high-speed USB device number 8 using dummy_hcd
[  124.858195][ T6080] em28xx 3-1:0.132: board has no eeprom
[  124.875779][ T6083] usb 2-1: SerialNumber: syz
[  124.880995][ T5953] usb 1-1: Manufacturer: syz
[  124.887265][ T5953] usb 1-1: SerialNumber: syz
[  124.888667][ T6083] usb 2-1: config 0 descriptor??
[  124.900389][ T5953] usb 1-1: config 0 descriptor??
[  124.906731][ T6246] raw-gadget.3 gadget.0: fail, usb_ep_enable returned -22
[  124.914903][ T6240] raw-gadget.0 gadget.1: fail, usb_ep_enable returned -22
[  124.926403][ T5953] em28xx 1-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  124.926631][ T6083] em28xx 2-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  124.937158][ T5953] em28xx 1-1:0.132: Video interface 132 found: bulk
[  124.956566][ T6080] em28xx 3-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  124.964549][ T6080] em28xx 3-1:0.132: analog set to bulk mode.
[  124.996212][ T6080] usb 3-1: USB disconnect, device number 8
[  125.020843][ T6083] em28xx 2-1:0.132: Video interface 132 found: bulk
[  125.030879][    T9] usb 5-1: Using ep0 maxpacket: 32
[  125.030986][ T6080] em28xx 3-1:0.132: Disconnecting em28xx
[  125.042471][    T9] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[  125.065360][ T6090] em28xx 4-1:0.132: Config register raw data: 0xffffffed
[  125.072519][    T9] usb 5-1: config 0 has no interface number 0
[  125.072574][    T9] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  125.078703][    T9] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  125.080618][ T6090] em28xx 4-1:0.132: AC97 chip type couldn't be determined
[  125.093561][    T9] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  125.119122][ T6090] em28xx 4-1:0.132: No AC97 audio processor
[  125.134131][    T9] usb 5-1: Product: syz
[  125.138946][    T9] usb 5-1: Manufacturer: syz
[  125.148064][    T9] usb 5-1: SerialNumber: syz
[  125.150081][ T6090] usb 4-1: Decoder not found
[  125.155780][    T9] usb 5-1: config 0 descriptor??
[  125.167555][ T6245] raw-gadget.2 gadget.4: fail, usb_ep_enable returned -22
[  125.172885][ T6090] em28xx 4-1:0.132: failed to create media graph
[  125.184236][ T6090] em28xx 4-1:0.132: V4L2 device video103 deregistered
[  125.187209][    T9] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  125.197437][ T6090] em28xx 4-1:0.132: Remote control support is not available for this card.
[  125.201896][ T5953] em28xx 1-1:0.132: unknown em28xx chip ID (0)
[  125.210398][   T43] em28xx 3-1:0.132: Registering V4L2 extension
[  125.223729][ T6083] em28xx 2-1:0.132: unknown em28xx chip ID (0)
[  125.261564][    T9] em28xx 5-1:0.132: Video interface 132 found: bulk
[  125.306359][ T6083] em28xx 2-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  125.321051][ T5953] em28xx 1-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  125.325551][ T6083] em28xx 2-1:0.132: board has no eeprom
[  125.351361][ T5953] em28xx 1-1:0.132: board has no eeprom
[  125.410859][   T43] em28xx 3-1:0.132: Config register raw data: 0xffffffed
[  125.418222][   T43] em28xx 3-1:0.132: AC97 chip type couldn't be determined
[  125.421383][ T5953] em28xx 1-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  125.426091][ T6083] em28xx 2-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  125.433778][ T5953] em28xx 1-1:0.132: analog set to bulk mode.
[  125.445218][ T5953] usb 1-1: USB disconnect, device number 8
[  125.455590][   T43] em28xx 3-1:0.132: No AC97 audio processor
[  125.460410][    T9] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[  125.469909][ T6083] em28xx 2-1:0.132: analog set to bulk mode.
[  125.476696][   T43] usb 3-1: Decoder not found
[  125.477683][ T5953] em28xx 1-1:0.132: Disconnecting em28xx
[  125.481514][   T43] em28xx 3-1:0.132: failed to create media graph
[  125.481549][   T43] em28xx 3-1:0.132: V4L2 device video103 deregistered
[  125.507499][   T43] em28xx 3-1:0.132: Remote control support is not available for this card.
[  125.519549][   T24] em28xx 4-1:0.132: Closing input extension
[  125.527913][ T6083] usb 2-1: USB disconnect, device number 8
[  125.534809][ T6032] em28xx 1-1:0.132: Registering V4L2 extension
[  125.536564][ T6083] em28xx 2-1:0.132: Disconnecting em28xx
[  125.552021][   T24] em28xx 4-1:0.132: Freeing device
[  125.573897][    T9] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  125.583662][    T9] em28xx 5-1:0.132: board has no eeprom
[  125.656286][    T9] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  125.702633][    T9] em28xx 5-1:0.132: analog set to bulk mode.
[  125.752034][    T9] usb 5-1: USB disconnect, device number 8
[  125.764167][    T9] em28xx 5-1:0.132: Disconnecting em28xx
[  125.817947][ T6032] em28xx 1-1:0.132: Config register raw data: 0xffffffed
[  125.825693][ T6032] em28xx 1-1:0.132: AC97 chip type couldn't be determined
[  125.834297][ T6032] em28xx 1-1:0.132: No AC97 audio processor
[  125.842205][ T6032] usb 1-1: Decoder not found
[  125.847166][ T6032] em28xx 1-1:0.132: failed to create media graph
[  125.854348][ T6032] em28xx 1-1:0.132: V4L2 device video103 deregistered
[  125.864225][ T6032] em28xx 1-1:0.132: Remote control support is not available for this card.
[  125.870728][   T24] usb 4-1: new high-speed USB device number 9 using dummy_hcd
[  125.873050][ T5953] em28xx 1-1:0.132: Closing input extension
[  125.887201][ T6090] em28xx 2-1:0.132: Registering V4L2 extension
[  125.891170][ T5953] em28xx 1-1:0.132: Freeing device
[  126.026764][ T6090] em28xx 2-1:0.132: Config register raw data: 0xffffffed
[  126.035378][ T6090] em28xx 2-1:0.132: AC97 chip type couldn't be determined
[  126.042837][ T6090] em28xx 2-1:0.132: No AC97 audio processor
[  126.050235][ T6090] usb 2-1: Decoder not found
[  126.055156][   T24] usb 4-1: Using ep0 maxpacket: 32
[  126.060969][ T6090] em28xx 2-1:0.132: failed to create media graph
[  126.067621][ T6090] em28xx 2-1:0.132: V4L2 device video103 deregistered
[  126.075778][   T24] usb 4-1: config 0 has an invalid interface number: 132 but max is 0
[  126.084507][   T24] usb 4-1: config 0 has no interface number 0
[  126.091621][ T6090] em28xx 2-1:0.132: Remote control support is not available for this card.
[  126.101331][ T6080] em28xx 3-1:0.132: Closing input extension
[  126.107417][ T5830] em28xx 5-1:0.132: Registering V4L2 extension
[  126.110758][   T24] usb 4-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  126.127489][ T6080] em28xx 3-1:0.132: Freeing device
[  126.145494][   T24] usb 4-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  126.170108][   T24] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  126.179593][   T24] usb 4-1: Product: syz
[  126.185313][   T24] usb 4-1: Manufacturer: syz
[  126.190039][   T24] usb 4-1: SerialNumber: syz
[  126.202105][   T24] usb 4-1: config 0 descriptor??
[  126.208178][ T6257] raw-gadget.1 gadget.3: fail, usb_ep_enable returned -22
[  126.233322][ T5953] usb 1-1: new high-speed USB device number 9 using dummy_hcd
[  126.234579][   T24] em28xx 4-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  126.259067][   T24] em28xx 4-1:0.132: Video interface 132 found: bulk
[  126.330768][ T5830] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[  126.338343][ T5830] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[  126.348905][ T5830] em28xx 5-1:0.132: No AC97 audio processor
[  126.357377][ T5830] usb 5-1: Decoder not found
[  126.363669][ T5830] em28xx 5-1:0.132: failed to create media graph
[  126.370137][ T5830] em28xx 5-1:0.132: V4L2 device video103 deregistered
[  126.379989][ T5830] em28xx 5-1:0.132: Remote control support is not available for this card.
[  126.392517][ T6083] em28xx 2-1:0.132: Closing input extension
[  126.398825][    T9] em28xx 5-1:0.132: Closing input extension
[  126.423572][    T9] em28xx 5-1:0.132: Freeing device
[  126.424466][ T6083] em28xx 2-1:0.132: Freeing device
[  126.438657][ T6080] usb 3-1: new high-speed USB device number 9 using dummy_hcd
[  126.440655][ T5953] usb 1-1: Using ep0 maxpacket: 32
[  126.465566][ T5953] usb 1-1: config 0 has an invalid interface number: 132 but max is 0
[  126.477226][ T5953] usb 1-1: config 0 has no interface number 0
[  126.484306][ T5953] usb 1-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  126.502755][   T24] em28xx 4-1:0.132: unknown em28xx chip ID (0)
[  126.517786][ T5953] usb 1-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  126.531734][ T5953] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  126.539789][ T5953] usb 1-1: Product: syz
[  126.544444][ T5953] usb 1-1: Manufacturer: syz
[  126.549081][ T5953] usb 1-1: SerialNumber: syz
[  126.559275][ T5953] usb 1-1: config 0 descriptor??
[  126.565068][ T6267] raw-gadget.2 gadget.0: fail, usb_ep_enable returned -22
[  126.578219][   T24] em28xx 4-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  126.588038][   T24] em28xx 4-1:0.132: board has no eeprom
[  126.601030][ T6080] usb 3-1: Using ep0 maxpacket: 32
[  126.601411][ T5953] em28xx 1-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  126.619361][ T6080] usb 3-1: config 0 has an invalid interface number: 132 but max is 0
[  126.632450][ T6080] usb 3-1: config 0 has no interface number 0
[  126.636407][ T5953] em28xx 1-1:0.132: Video interface 132 found: bulk
[  126.645487][ T6080] usb 3-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  126.648056][ T6080] usb 3-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  126.666379][   T24] em28xx 4-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  126.676233][   T24] em28xx 4-1:0.132: analog set to bulk mode.
[  126.683052][ T6089] em28xx 4-1:0.132: Registering V4L2 extension
[  126.691147][ T6080] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  126.715553][   T24] usb 4-1: USB disconnect, device number 9
[  126.740347][ T6080] usb 3-1: Product: syz
[  126.747762][   T24] em28xx 4-1:0.132: Disconnecting em28xx
[  126.765827][ T6080] usb 3-1: Manufacturer: syz
[  126.791219][ T6083] usb 2-1: new high-speed USB device number 9 using dummy_hcd
[  126.800302][ T6080] usb 3-1: SerialNumber: syz
[  126.813143][    T9] usb 5-1: new high-speed USB device number 9 using dummy_hcd
[  126.825827][ T6080] usb 3-1: config 0 descriptor??
[  126.844296][ T6259] raw-gadget.0 gadget.2: fail, usb_ep_enable returned -22
[  126.872437][ T5953] em28xx 1-1:0.132: unknown em28xx chip ID (0)
[  126.884271][ T6080] em28xx 3-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  126.895265][ T6080] em28xx 3-1:0.132: Video interface 132 found: bulk
[  126.935467][ T5953] em28xx 1-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  126.955203][ T6089] em28xx 4-1:0.132: Config register raw data: 0xffffffed
[  126.955241][ T5953] em28xx 1-1:0.132: board has no eeprom
[  126.962904][ T6083] usb 2-1: Using ep0 maxpacket: 32
[  126.965416][ T6089] em28xx 4-1:0.132: AC97 chip type couldn't be determined
[  126.982670][ T6083] usb 2-1: config 0 has an invalid interface number: 132 but max is 0
[  126.991924][ T6083] usb 2-1: config 0 has no interface number 0
2025/10/22 15:26:12 executed programs: 50
[  126.998185][ T6083] usb 2-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  127.013511][    T9] usb 5-1: Using ep0 maxpacket: 32
[  127.021767][ T6089] em28xx 4-1:0.132: No AC97 audio processor
[  127.032519][ T5953] em28xx 1-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  127.033535][ T6083] usb 2-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  127.040373][ T5953] em28xx 1-1:0.132: analog set to bulk mode.
[  127.044885][    T9] usb 5-1: config 0 has an invalid interface number: 132 but max is 0
[  127.054368][ T6083] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  127.072806][ T6089] usb 4-1: Decoder not found
[  127.077439][ T6089] em28xx 4-1:0.132: failed to create media graph
[  127.084148][ T5953] usb 1-1: USB disconnect, device number 9
[  127.091912][ T6089] em28xx 4-1:0.132: V4L2 device video103 deregistered
[  127.095751][    T9] usb 5-1: config 0 has no interface number 0
[  127.099436][ T6083] usb 2-1: Product: syz
[  127.112499][ T6083] usb 2-1: Manufacturer: syz
[  127.112803][ T5953] em28xx 1-1:0.132: Disconnecting em28xx
[  127.123869][ T6089] em28xx 4-1:0.132: Remote control support is not available for this card.
[  127.123943][   T24] em28xx 4-1:0.132: Closing input extension
[  127.125031][ T6083] usb 2-1: SerialNumber: syz
[  127.135221][ T5830] em28xx 1-1:0.132: Registering V4L2 extension
[  127.146757][   T24] em28xx 4-1:0.132: Freeing device
[  127.150778][    T9] usb 5-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  127.156641][ T6080] em28xx 3-1:0.132: unknown em28xx chip ID (0)
[  127.169471][    T9] usb 5-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  127.174613][ T6083] usb 2-1: config 0 descriptor??
[  127.189123][    T9] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  127.205795][ T6268] raw-gadget.3 gadget.1: fail, usb_ep_enable returned -22
[  127.217636][    T9] usb 5-1: Product: syz
[  127.217778][ T6083] em28xx 2-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  127.227780][    T9] usb 5-1: Manufacturer: syz
[  127.245416][    T9] usb 5-1: SerialNumber: syz
[  127.254558][ T6083] em28xx 2-1:0.132: Video interface 132 found: bulk
[  127.266574][    T9] usb 5-1: config 0 descriptor??
[  127.276183][ T6271] raw-gadget.4 gadget.4: fail, usb_ep_enable returned -22
[  127.293555][ T6080] em28xx 3-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  127.296227][    T9] em28xx 5-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  127.320889][ T6080] em28xx 3-1:0.132: board has no eeprom
[  127.374635][    T9] em28xx 5-1:0.132: Video interface 132 found: bulk
[  127.399341][ T6080] em28xx 3-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  127.432216][ T6080] em28xx 3-1:0.132: analog set to bulk mode.
[  127.467996][ T6080] usb 3-1: USB disconnect, device number 9
[  127.480162][ T6083] em28xx 2-1:0.132: unknown em28xx chip ID (0)
[  127.482658][ T5830] em28xx 1-1:0.132: Config register raw data: 0xffffffed
[  127.490298][ T6080] em28xx 3-1:0.132: Disconnecting em28xx
[  127.501388][   T24] usb 4-1: new high-speed USB device number 10 using dummy_hcd
[  127.504796][ T5830] em28xx 1-1:0.132: AC97 chip type couldn't be determined
[  127.516161][ T5830] em28xx 1-1:0.132: No AC97 audio processor
[  127.526321][ T5830] usb 1-1: Decoder not found
[  127.532872][ T5830] em28xx 1-1:0.132: failed to create media graph
[  127.539257][ T5830] em28xx 1-1:0.132: V4L2 device video103 deregistered
[  127.544517][ T6083] em28xx 2-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  127.548222][ T5830] em28xx 1-1:0.132: Remote control support is not available for this card.
[  127.555571][ T6083] em28xx 2-1:0.132: board has no eeprom
[  127.571121][    T9] em28xx 5-1:0.132: unknown em28xx chip ID (0)
[  127.577538][ T5953] em28xx 1-1:0.132: Closing input extension
[  127.586393][ T6089] em28xx 3-1:0.132: Registering V4L2 extension
[  127.589718][ T5953] em28xx 1-1:0.132: Freeing device
[  127.639125][ T6083] em28xx 2-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  127.655173][    T9] em28xx 5-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  127.665037][   T24] usb 4-1: Using ep0 maxpacket: 32
[  127.670478][ T6083] em28xx 2-1:0.132: analog set to bulk mode.
[  127.674315][    T9] em28xx 5-1:0.132: board has no eeprom
[  127.696768][   T24] usb 4-1: config 0 has an invalid interface number: 132 but max is 0
[  127.722064][   T24] usb 4-1: config 0 has no interface number 0
[  127.739376][ T6083] usb 2-1: USB disconnect, device number 9
[  127.746796][   T24] usb 4-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  127.760804][    T9] em28xx 5-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  127.761998][ T6083] em28xx 2-1:0.132: Disconnecting em28xx
[  127.768728][    T9] em28xx 5-1:0.132: analog set to bulk mode.
[  127.783679][   T24] usb 4-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  127.793513][   T24] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  127.806714][   T24] usb 4-1: Product: syz
[  127.807683][    T9] usb 5-1: USB disconnect, device number 9
[  127.813645][   T24] usb 4-1: Manufacturer: syz
[  127.823766][    T9] em28xx 5-1:0.132: Disconnecting em28xx
[  127.839807][   T24] usb 4-1: SerialNumber: syz
[  127.860998][   T24] usb 4-1: config 0 descriptor??
[  127.867600][ T6284] raw-gadget.1 gadget.3: fail, usb_ep_enable returned -22
[  127.887210][   T24] em28xx 4-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  127.898870][   T24] em28xx 4-1:0.132: Video interface 132 found: bulk
[  127.909844][ T6089] em28xx 3-1:0.132: Config register raw data: 0xffffffed
[  127.917128][ T6089] em28xx 3-1:0.132: AC97 chip type couldn't be determined
[  127.925698][ T6089] em28xx 3-1:0.132: No AC97 audio processor
[  127.926049][ T5953] usb 1-1: new high-speed USB device number 10 using dummy_hcd
[  127.963233][ T6089] usb 3-1: Decoder not found
[  127.983207][ T6089] em28xx 3-1:0.132: failed to create media graph
[  127.990199][ T6089] em28xx 3-1:0.132: V4L2 device video103 deregistered
[  127.999357][ T6089] em28xx 3-1:0.132: Remote control support is not available for this card.
[  128.011830][   T43] em28xx 2-1:0.132: Registering V4L2 extension
[  128.100708][ T5953] usb 1-1: Using ep0 maxpacket: 32
[  128.117548][ T5953] usb 1-1: config 0 has an invalid interface number: 132 but max is 0
[  128.127557][ T5953] usb 1-1: config 0 has no interface number 0
[  128.136877][ T5953] usb 1-1: config 0 interface 132 altsetting 0 bulk endpoint 0x82 has invalid maxpacket 32
[  128.141024][   T24] em28xx 4-1:0.132: unknown em28xx chip ID (0)
[  128.156226][ T5953] usb 1-1: New USB device found, idVendor=0413, idProduct=6023, bcdDevice=ec.e5
[  128.166430][ T5953] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  128.175242][ T5953] usb 1-1: Product: syz
[  128.179762][ T5953] usb 1-1: Manufacturer: syz
[  128.185006][ T5953] usb 1-1: SerialNumber: syz
[  128.185752][   T43] em28xx 2-1:0.132: Config register raw data: 0xffffffed
[  128.193108][ T5953] usb 1-1: config 0 descriptor??
[  128.196933][   T43] em28xx 2-1:0.132: AC97 chip type couldn't be determined
[  128.208323][ T6288] raw-gadget.0 gadget.0: fail, usb_ep_enable returned -22
[  128.209235][   T43] em28xx 2-1:0.132: No AC97 audio processor
[  128.221609][ T5953] em28xx 1-1:0.132: New device syz syz @ 480 Mbps (0413:6023, interface 132, class 132)
[  128.231657][   T24] em28xx 4-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  128.233738][ T5953] em28xx 1-1:0.132: Video interface 132 found: bulk
[  128.243274][   T43] usb 2-1: Decoder not found
[  128.256796][   T43] em28xx 2-1:0.132: failed to create media graph
[  128.263602][   T24] em28xx 4-1:0.132: board has no eeprom
[  128.269379][   T43] em28xx 2-1:0.132: V4L2 device video103 deregistered
[  128.278780][   T43] em28xx 2-1:0.132: Remote control support is not available for this card.
[  128.287865][ T6040] em28xx 5-1:0.132: Registering V4L2 extension
[  128.330684][   T24] em28xx 4-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  128.338575][   T24] em28xx 4-1:0.132: analog set to bulk mode.
[  128.366285][   T24] usb 4-1: USB disconnect, device number 10
[  128.381834][   T24] em28xx 4-1:0.132: Disconnecting em28xx
[  128.429744][ T6040] em28xx 5-1:0.132: Config register raw data: 0xffffffed
[  128.437340][ T6040] em28xx 5-1:0.132: AC97 chip type couldn't be determined
[  128.445420][ T6040] em28xx 5-1:0.132: No AC97 audio processor
[  128.455961][ T6040] usb 5-1: Decoder not found
[  128.460943][ T6040] em28xx 5-1:0.132: failed to create media graph
[  128.467583][ T6040] em28xx 5-1:0.132: V4L2 device video103 deregistered
[  128.474845][ T5953] em28xx 1-1:0.132: unknown em28xx chip ID (0)
[  128.483391][ T6040] em28xx 5-1:0.132: Remote control support is not available for this card.
[  128.492303][ T6080] em28xx 3-1:0.132: Closing input extension
[  128.500031][ T6083] em28xx 2-1:0.132: Closing input extension
[  128.507460][   T43] em28xx 4-1:0.132: Registering V4L2 extension
[  128.515559][ T6080] em28xx 3-1:0.132: Freeing device
[  128.527676][ T6083] em28xx 2-1:0.132: Freeing device
[  128.568169][ T5953] em28xx 1-1:0.132: failed to trigger read from i2c address 0xa0 (error=-5)
[  128.593013][ T5953] em28xx 1-1:0.132: board has no eeprom
[  128.665671][ T5953] em28xx 1-1:0.132: Identified as Leadtek Winfast USB II (card=7)
[  128.694559][ T5953] em28xx 1-1:0.132: analog set to bulk mode.
[  128.723843][ T5953] usb 1-1: USB disconnect, device number 10
[  128.749910][ T5953] em28xx 1-1:0.132: Disconnecting em28xx
[  128.775508][   T43] em28xx 4-1:0.132: Config register raw data: 0xffffffed
[  128.786212][   T43] em28xx 4-1:0.132: AC97 chip type couldn't be determined
[  128.794555][   T43] em28xx 4-1:0.132: No AC97 audio processor
[  128.803067][   T43] usb 4-1: Decoder not found
[  128.808176][   T43] em28xx 4-1:0.132: failed to create media graph
[  128.817479][   T43] em28xx 4-1:0.132: V4L2 device video103 deregistered
[  128.828126][   T43] em28xx 4-1:0.132: Remote control support is not available for this card.
[  128.828371][ T6308] ==================================================================
[  128.837728][ T6080] usb 3-1: new high-speed USB device number 10 using dummy_hcd
[  128.844895][ T6308] BUG: KASAN: slab-use-after-free in v4l2_fh_open+0xac/0x420
[  128.844935][ T6308] Read of size 8 at addr ffff888032e58740 by task v4l_id/6308
[  128.844951][ T6308] 
[  128.844963][ T6308] CPU: 0 UID: 0 PID: 6308 Comm: v4l_id Not tainted syzkaller #0 PREEMPT(full) 
[  128.844984][ T6308] Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/02/2025
[  128.844995][ T6308] Call Trace:
[  128.845002][ T6308]  <TASK>
[  128.845010][ T6308]  dump_stack_lvl+0x189/0x250
[  128.845037][ T6308]  ? __virt_addr_valid+0x1c8/0x5c0
[  128.845061][ T6308]  ? rcu_is_watching+0x15/0xb0
[  128.845081][ T6308]  ? __pfx_dump_stack_lvl+0x10/0x10
[  128.845103][ T6308]  ? rcu_is_watching+0x15/0xb0
[  128.845122][ T6308]  ? lock_release+0x4b/0x3e0
[  128.845138][ T6308]  ? _raw_spin_lock_irqsave+0xb3/0xf0
[  128.845168][ T6308]  ? __virt_addr_valid+0x1c8/0x5c0
[  128.845190][ T6308]  ? __virt_addr_valid+0x4a5/0x5c0
[  128.845213][ T6308]  print_report+0xca/0x240
[  128.845234][ T6308]  ? v4l2_fh_open+0xac/0x420
[  128.845249][ T6308]  kasan_report+0x118/0x150
[  128.845267][ T6308]  ? v4l2_fh_open+0xac/0x420
[  128.845284][ T6308]  v4l2_fh_open+0xac/0x420
[  128.845300][ T6308]  ? __pfx___mutex_unlock_slowpath+0x10/0x10
[  128.845325][ T6308]  em28xx_v4l2_open+0x157/0x9a0
[  128.845352][ T6308]  v4l2_open+0x1bf/0x3a0
[  128.845371][ T6308]  chrdev_open+0x4cc/0x5e0
[  128.845389][ T6308]  ? __pfx_chrdev_open+0x10/0x10
[  128.845405][ T6308]  ? fsnotify_open_perm_and_set_mode+0x113/0x610
[  128.845426][ T6308]  ? __pfx_chrdev_open+0x10/0x10
[  128.845441][ T6308]  do_dentry_open+0x953/0x13f0
[  128.845465][ T6308]  vfs_open+0x3b/0x340
[  128.845482][ T6308]  ? path_openat+0x2ecd/0x3830
[  128.845504][ T6308]  path_openat+0x2ee5/0x3830
[  128.845537][ T6308]  ? __pfx_path_openat+0x10/0x10
[  128.845565][ T6308]  do_filp_open+0x1fa/0x410
[  128.845584][ T6308]  ? __lock_acquire+0xab9/0xd20
[  128.845601][ T6308]  ? __pfx_do_filp_open+0x10/0x10
[  128.845629][ T6308]  ? _raw_spin_unlock+0x28/0x50
[  128.845647][ T6308]  ? alloc_fd+0x64c/0x6c0
[  128.845676][ T6308]  do_sys_openat2+0x121/0x1c0
[  128.845696][ T6308]  ? __pfx_do_sys_openat2+0x10/0x10
[  128.845716][ T6308]  ? exc_page_fault+0x82/0x100
[  128.845737][ T6308]  ? do_user_addr_fault+0xc85/0x1380
[  128.845756][ T6308]  __x64_sys_openat+0x138/0x170
[  128.845777][ T6308]  do_syscall_64+0xfa/0xfa0
[  128.845797][ T6308]  ? lockdep_hardirqs_on+0x9c/0x150
[  128.845817][ T6308]  ? entry_SYSCALL_64_after_hwframe+0x77/0x7f
[  128.845834][ T6308]  ? clear_bhb_loop+0x60/0xb0
[  128.845853][ T6308]  entry_SYSCALL_64_after_hwframe+0x77/0x7f
[  128.845870][ T6308] RIP: 0033:0x7f3a484a7407
[  128.845885][ T6308] Code: 48 89 fa 4c 89 df e8 38 aa 00 00 8b 93 08 03 00 00 59 5e 48 83 f8 fc 74 1a 5b c3 0f 1f 84 00 00 00 00 00 48 8b 44 24 10 0f 05 <5b> c3 0f 1f 80 00 00 00 00 83 e2 39 83 fa 08 75 de e8 23 ff ff ff
[  128.845900][ T6308] RSP: 002b:00007ffd407196b0 EFLAGS: 00000202 ORIG_RAX: 0000000000000101
[  128.845921][ T6308] RAX: ffffffffffffffda RBX: 00007f3a48c1b880 RCX: 00007f3a484a7407
[  128.845933][ T6308] RDX: 0000000000000000 RSI: 00007ffd4071af1b RDI: ffffffffffffff9c
[  128.845946][ T6308] RBP: 0000000000000002 R08: 0000000000000000 R09: 0000000000000000
[  128.845956][ T6308] R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000000
[  128.845967][ T6308] R13: 00007ffd40719900 R14: 00007f3a48d82000 R15: 000055f424f9d4d8
[  128.845986][ T6308]  </TASK>
[  128.845992][ T6308] 
[  128.852928][ T6083] usb 2-1: new high-speed USB device number 10 using dummy_hcd
[  128.860378][ T6308] Allocated by task 43:
[  128.860397][ T6308]  kasan_save_track+0x3e/0x80
[  128.860427][ T6308]  __kasan_kmalloc+0x93/0xb0
[  129.203101][ T6308]  __kmalloc_cache_noprof+0x3d5/0x6f0
[  129.208681][ T6308]  em28xx_v4l2_init+0x10b/0x2e70
[  129.213705][ T6308]  em28xx_init_extension+0x120/0x1c0
[  129.219092][ T6308]  process_scheduled_works+0xae1/0x17b0
[  129.224642][ T6308]  worker_thread+0x8a0/0xda0
[  129.229321][ T6308]  kthread+0x711/0x8a0
[  129.233398][ T6308]  ret_from_fork+0x4bc/0x870
[  129.238325][ T6308]  ret_from_fork_asm+0x1a/0x30
[  129.243137][ T6308] 
[  129.245478][ T6308] Freed by task 43:
[  129.249283][ T6308]  kasan_save_track+0x3e/0x80
[  129.253975][ T6308]  __kasan_save_free_info+0x46/0x50
[  129.259214][ T6308]  __kasan_slab_free+0x5c/0x80
[  129.264186][ T6308]  kfree+0x19a/0x6d0
[  129.268096][ T6308]  em28xx_v4l2_init+0x1683/0x2e70
[  129.273140][ T6308]  em28xx_init_extension+0x120/0x1c0
[  129.278516][ T6308]  process_scheduled_works+0xae1/0x17b0
[  129.284076][ T6308]  worker_thread+0x8a0/0xda0
[  129.288757][ T6308]  kthread+0x711/0x8a0
[  129.292923][ T6308]  ret_from_fork+0x4bc/0x870
[  129.297516][ T6308]  ret_from_fork_asm+0x1a/0x30
[  129.302464][ T6308] 
[  129.305071][ T6308] The buggy address belongs to the object at ffff888032e58000
[  129.305071][ T6308]  which belongs to the cache kmalloc-8k of size 8192
[  129.319225][ T6308] The buggy address is located 1856 bytes inside of
[  129.319225][ T6308]  freed 8192-byte region [ffff888032e58000, ffff888032e5a000)
[  129.333375][ T6308] 
[  129.335701][ T6308] The buggy address belongs to the physical page:
[  129.342120][ T6308] page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x32e58
[  129.350887][ T6308] head: order:3 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
[  129.359907][ T6308] flags: 0xfff00000000040(head|node=0|zone=1|lastcpupid=0x7ff)
[  129.367737][ T6308] page_type: f5(slab)
[  129.371723][ T6308] raw: 00fff00000000040 ffff88801a027280 ffffea0000a16c00 dead000000000004
[  129.380326][ T6308] raw: 0000000000000000 0000000080020002 00000000f5000000 0000000000000000
[  129.389018][ T6308] head: 00fff00000000040 ffff88801a027280 ffffea0000a16c00 dead000000000004
[  129.397717][ T6308] head: 0000000000000000 0000000080020002 00000000f5000000 0000000000000000
[  129.406404][ T6308] head: 00fff00000000003 ffffea0000cb9601 00000000ffffffff 00000000ffffffff
[  129.415260][ T6308] head: ffffffffffffffff 0000000000000000 00000000ffffffff 0000000000000008
[  129.424110][ T6308] page dumped because: kasan: bad access detected
[  129.430795][ T6308] page_owner tracks the page as allocated
[  129.436615][ T6308] page last allocated via order 3, migratetype Unmovable, gfp_mask 0xd2040(__GFP_IO|__GFP_NOWARN|__GFP_NORETRY|__GFP_COMP|__GFP_NOMEMALLOC), pid 5502, tgid 5502 (dhcpcd-run-hook), ts 56728219653, free_ts 56681301722
[  129.457558][ T6308]  post_alloc_hook+0x240/0x2a0
[  129.462511][ T6308]  get_page_from_freelist+0x2365/0x2440
[  129.468069][ T6308]  __alloc_frozen_pages_noprof+0x181/0x370
[  129.473879][ T6308]  alloc_pages_mpol+0x232/0x4a0
[  129.478727][ T6308]  allocate_slab+0x96/0x3a0
[  129.483328][ T6308]  ___slab_alloc+0xe94/0x18a0
[  129.488128][ T6308]  __slab_alloc+0x65/0x100
[  129.492548][ T6308]  __kmalloc_cache_noprof+0x411/0x6f0
[  129.497927][ T6308]  tomoyo_init_log+0x111f/0x1f70
[  129.503046][ T6308]  tomoyo_supervisor+0x340/0x1480
[  129.508188][ T6308]  tomoyo_find_next_domain+0x488/0x1aa0
[  129.513947][ T6308]  tomoyo_bprm_check_security+0x11c/0x180
[  129.519700][ T6308]  security_bprm_check+0x89/0x270
[  129.524737][ T6308]  bprm_execve+0x8ee/0x1450
[  129.529262][ T6308]  do_execveat_common+0x510/0x6a0
[  129.534311][ T6308]  __x64_sys_execve+0x94/0xb0
[  129.539147][ T6308] page last free pid 5501 tgid 5501 stack trace:
[  129.545484][ T6308]  __free_frozen_pages+0xbc4/0xd30
[  129.550720][ T6308]  __put_partials+0x146/0x170
[  129.555396][ T6308]  put_cpu_partial+0x1f2/0x2e0
[  129.560247][ T6308]  __slab_free+0x2b9/0x390
[  129.564666][ T6308]  qlist_free_all+0x97/0x140
[  129.569438][ T6308]  kasan_quarantine_reduce+0x148/0x160
[  129.574914][ T6308]  __kasan_slab_alloc+0x22/0x80
[  129.579815][ T6308]  __kmalloc_cache_noprof+0x36f/0x6f0
[  129.585378][ T6308]  tomoyo_init_log+0x183/0x1f70
[  129.590326][ T6308]  tomoyo_supervisor+0x340/0x1480
[  129.595447][ T6308]  tomoyo_path_permission+0x25a/0x380
[  129.600826][ T6308]  tomoyo_path_perm+0x392/0x4b0
[  129.605680][ T6308]  security_inode_getattr+0x12f/0x330
[  129.611183][ T6308]  vfs_statx+0x18e/0x550
[  129.615430][ T6308]  vfs_fstatat+0x118/0x170
[  129.619850][ T6308]  __x64_sys_newfstatat+0x116/0x190
[  129.625094][ T6308] 
[  129.627419][ T6308] Memory state around the buggy address:
[  129.633046][ T6308]  ffff888032e58600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  129.641126][ T6308]  ffff888032e58680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  129.649407][ T6308] >ffff888032e58700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  129.657567][ T6308]                                            ^
[  129.663807][ T6308]  ffff888032e58780: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  129.672564][ T6308]  ffff888032e58800: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  129.680758][ T6308] ==================================================================
[  129.706478][    T9] em28xx 5-1:0.132: Closing input extension
[  129.713154][   T24] em28xx 4-1:0.132: Closing input extension
[  129.725536][ T6040] em28xx 1-1:0.132: Registering V4L2 extension
[  129.753427][    T9] em28xx 5-1:0.132: Freeing device
[  129.777912][ T6308] Kernel panic - not syncing: KASAN: panic_on_warn set ...
[  129.785163][ T6308] CPU: 0 UID: 0 PID: 6308 Comm: v4l_id Not tainted syzkaller #0 PREEMPT(full) 
[  129.794140][ T6308] Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/02/2025
[  129.804225][ T6308] Call Trace:
[  129.807533][ T6308]  <TASK>
[  129.810488][ T6308]  dump_stack_lvl+0x99/0x250
[  129.815203][ T6308]  ? __asan_memcpy+0x40/0x70
[  129.819922][ T6308]  ? __pfx_dump_stack_lvl+0x10/0x10
[  129.825160][ T6308]  ? __pfx__printk+0x10/0x10
[  129.829965][ T6308]  vpanic+0x237/0x6d0
[  129.833999][ T6308]  ? __pfx_vpanic+0x10/0x10
[  129.838539][ T6308]  ? preempt_schedule+0xae/0xc0
[  129.843401][ T6308]  ? __pfx_preempt_schedule+0x10/0x10
[  129.848800][ T6308]  panic+0xb9/0xc0
[  129.852547][ T6308]  ? __pfx_panic+0x10/0x10
[  129.856978][ T6308]  ? _raw_spin_unlock_irqrestore+0xfd/0x110
[  129.862899][ T6308]  ? is_module_address+0x17/0xf0
[  129.867848][ T6308]  ? v4l2_fh_open+0xac/0x420
[  129.872529][ T6308]  check_panic_on_warn+0x89/0xb0
[  129.877482][ T6308]  ? v4l2_fh_open+0xac/0x420
[  129.882091][ T6308]  end_report+0x78/0x160
[  129.886382][ T6308]  kasan_report+0x129/0x150
[  129.891004][ T6308]  ? v4l2_fh_open+0xac/0x420
[  129.895796][ T6308]  v4l2_fh_open+0xac/0x420
[  129.900677][ T6308]  ? __pfx___mutex_unlock_slowpath+0x10/0x10
[  129.906874][ T6308]  em28xx_v4l2_open+0x157/0x9a0
[  129.911944][ T6308]  v4l2_open+0x1bf/0x3a0
[  129.916208][ T6308]  chrdev_open+0x4cc/0x5e0
[  129.920724][ T6308]  ? __pfx_chrdev_open+0x10/0x10
[  129.925678][ T6308]  ? fsnotify_open_perm_and_set_mode+0x113/0x610
[  129.932016][ T6308]  ? __pfx_chrdev_open+0x10/0x10
[  129.936967][ T6308]  do_dentry_open+0x953/0x13f0
[  129.941741][ T6308]  vfs_open+0x3b/0x340
[  129.945835][ T6308]  ? path_openat+0x2ecd/0x3830
[  129.950645][ T6308]  path_openat+0x2ee5/0x3830
[  129.955264][ T6308]  ? __pfx_path_openat+0x10/0x10
[  129.960214][ T6308]  do_filp_open+0x1fa/0x410
[  129.964722][ T6308]  ? __lock_acquire+0xab9/0xd20
[  129.969576][ T6308]  ? __pfx_do_filp_open+0x10/0x10
[  129.974616][ T6308]  ? _raw_spin_unlock+0x28/0x50
[  129.979473][ T6308]  ? alloc_fd+0x64c/0x6c0
[  129.983816][ T6308]  do_sys_openat2+0x121/0x1c0
[  129.988615][ T6308]  ? __pfx_do_sys_openat2+0x10/0x10
[  129.993865][ T6308]  ? exc_page_fault+0x82/0x100
[  129.998679][ T6308]  ? do_user_addr_fault+0xc85/0x1380
[  130.004018][ T6308]  __x64_sys_openat+0x138/0x170
[  130.008942][ T6308]  do_syscall_64+0xfa/0xfa0
[  130.013470][ T6308]  ? lockdep_hardirqs_on+0x9c/0x150
[  130.018682][ T6308]  ? entry_SYSCALL_64_after_hwframe+0x77/0x7f
[  130.024757][ T6308]  ? clear_bhb_loop+0x60/0xb0
[  130.030132][ T6308]  entry_SYSCALL_64_after_hwframe+0x77/0x7f
[  130.036031][ T6308] RIP: 0033:0x7f3a484a7407
[  130.040457][ T6308] Code: 48 89 fa 4c 89 df e8 38 aa 00 00 8b 93 08 03 00 00 59 5e 48 83 f8 fc 74 1a 5b c3 0f 1f 84 00 00 00 00 00 48 8b 44 24 10 0f 05 <5b> c3 0f 1f 80 00 00 00 00 83 e2 39 83 fa 08 75 de e8 23 ff ff ff
[  130.060255][ T6308] RSP: 002b:00007ffd407196b0 EFLAGS: 00000202 ORIG_RAX: 0000000000000101
[  130.068693][ T6308] RAX: ffffffffffffffda RBX: 00007f3a48c1b880 RCX: 00007f3a484a7407
[  130.076766][ T6308] RDX: 0000000000000000 RSI: 00007ffd4071af1b RDI: ffffffffffffff9c
[  130.084743][ T6308] RBP: 0000000000000002 R08: 0000000000000000 R09: 0000000000000000
[  130.093158][ T6308] R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000000
[  130.101142][ T6308] R13: 00007ffd40719900 R14: 00007f3a48d82000 R15: 000055f424f9d4d8
[  130.109311][ T6308]  </TASK>
[  130.112488][ T6308] Kernel Offset: disabled
[  130.116823][ T6308] Rebooting in 86400 seconds..