================================ WARNING: inconsistent lock state 4.14.231-syzkaller #0 Not tainted -------------------------------- inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage. syz-executor.2/11776 [HC0[0]:SC0[0]:HE1:SE1] takes: (slock-AF_BLUETOOTH-BTPROTO_SCO){+.?.}, at: [] spin_lock include/linux/spinlock.h:317 [inline] (slock-AF_BLUETOOTH-BTPROTO_SCO){+.?.}, at: [] sco_conn_del+0xbf/0x290 net/bluetooth/sco.c:175 {IN-SOFTIRQ-W} state was registered at: lock_acquire+0x170/0x3f0 kernel/locking/lockdep.c:3998 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x2a/0x40 kernel/locking/spinlock.c:152 spin_lock include/linux/spinlock.h:317 [inline] sco_sock_timeout+0x29/0x1c0 net/bluetooth/sco.c:82 call_timer_fn+0x14a/0x650 kernel/time/timer.c:1280 expire_timers+0x232/0x4d0 kernel/time/timer.c:1319 __run_timers kernel/time/timer.c:1637 [inline] run_timer_softirq+0x1d5/0x5a0 kernel/time/timer.c:1650 __do_softirq+0x24d/0x9ff kernel/softirq.c:288 invoke_softirq kernel/softirq.c:368 [inline] irq_exit+0x193/0x240 kernel/softirq.c:409 exiting_irq arch/x86/include/asm/apic.h:638 [inline] smp_apic_timer_interrupt+0x141/0x5e0 arch/x86/kernel/apic/apic.c:1106 apic_timer_interrupt+0x93/0xa0 arch/x86/entry/entry_64.S:793 arch_local_irq_disable arch/x86/include/asm/paravirt.h:784 [inline] arch_local_irq_save arch/x86/include/asm/paravirt.h:797 [inline] perf_lock_task_context+0xaf/0x750 kernel/events/core.c:1345 perf_pin_task_context kernel/events/core.c:1392 [inline] perf_event_exit_task_context kernel/events/core.c:10671 [inline] perf_event_exit_task+0x284/0xc90 kernel/events/core.c:10751 do_exit+0xa54/0x2850 kernel/exit.c:877 do_group_exit+0x100/0x2e0 kernel/exit.c:965 get_signal+0x38d/0x1ca0 kernel/signal.c:2423 do_signal+0x7c/0x1550 arch/x86/kernel/signal.c:792 exit_to_usermode_loop+0x160/0x200 arch/x86/entry/common.c:160 prepare_exit_to_usermode arch/x86/entry/common.c:199 [inline] syscall_return_slowpath arch/x86/entry/common.c:270 [inline] do_syscall_64+0x4a3/0x640 arch/x86/entry/common.c:297 entry_SYSCALL_64_after_hwframe+0x46/0xbb irq event stamp: 21527 hardirqs last enabled at (21527): [] __raw_spin_unlock_irq include/linux/spinlock_api_smp.h:168 [inline] hardirqs last enabled at (21527): [] _raw_spin_unlock_irq+0x24/0x80 kernel/locking/spinlock.c:200 hardirqs last disabled at (21526): [] __raw_spin_lock_irq include/linux/spinlock_api_smp.h:126 [inline] hardirqs last disabled at (21526): [] _raw_spin_lock_irq+0x35/0x80 kernel/locking/spinlock.c:168 softirqs last enabled at (19010): [] __do_softirq+0x68b/0x9ff kernel/softirq.c:314 softirqs last disabled at (18883): [] invoke_softirq kernel/softirq.c:368 [inline] softirqs last disabled at (18883): [] irq_exit+0x193/0x240 kernel/softirq.c:409 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(slock-AF_BLUETOOTH-BTPROTO_SCO); lock(slock-AF_BLUETOOTH-BTPROTO_SCO); *** DEADLOCK *** 3 locks held by syz-executor.2/11776: #0: (&hdev->req_lock){+.+.}, at: [] hci_dev_do_close+0x109/0xca0 net/bluetooth/hci_core.c:1578 #1: (&hdev->lock){+.+.}, at: [] hci_dev_do_close+0x21c/0xca0 net/bluetooth/hci_core.c:1609 #2: (hci_cb_list_lock){+.+.}, at: [] hci_disconn_cfm include/net/bluetooth/hci_core.h:1223 [inline] #2: (hci_cb_list_lock){+.+.}, at: [] hci_conn_hash_flush+0xda/0x260 net/bluetooth/hci_conn.c:1393 stack backtrace: CPU: 0 PID: 11776 Comm: syz-executor.2 Not tainted 4.14.231-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:17 [inline] dump_stack+0x1b2/0x281 lib/dump_stack.c:58 print_usage_bug.cold+0x42e/0x570 kernel/locking/lockdep.c:2589 valid_state kernel/locking/lockdep.c:2602 [inline] mark_lock_irq kernel/locking/lockdep.c:2796 [inline] mark_lock+0xb4d/0x1050 kernel/locking/lockdep.c:3194 mark_irqflags kernel/locking/lockdep.c:3090 [inline] __lock_acquire+0xd5c/0x3f20 kernel/locking/lockdep.c:3448 lock_acquire+0x170/0x3f0 kernel/locking/lockdep.c:3998 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x2a/0x40 kernel/locking/spinlock.c:152 spin_lock include/linux/spinlock.h:317 [inline] sco_conn_del+0xbf/0x290 net/bluetooth/sco.c:175 sco_disconn_cfm+0x65/0xa0 net/bluetooth/sco.c:1134 hci_disconn_cfm include/net/bluetooth/hci_core.h:1226 [inline] hci_conn_hash_flush+0x127/0x260 net/bluetooth/hci_conn.c:1393 hci_dev_do_close+0x535/0xca0 net/bluetooth/hci_core.c:1622 hci_unregister_dev+0x17f/0x8c0 net/bluetooth/hci_core.c:3193 vhci_release+0x70/0xe0 drivers/bluetooth/hci_vhci.c:354 __fput+0x25f/0x7a0 fs/file_table.c:210 task_work_run+0x11f/0x190 kernel/task_work.c:113 exit_task_work include/linux/task_work.h:22 [inline] do_exit+0xa44/0x2850 kernel/exit.c:868 do_group_exit+0x100/0x2e0 kernel/exit.c:965 get_signal+0x38d/0x1ca0 kernel/signal.c:2423 do_signal+0x7c/0x1550 arch/x86/kernel/signal.c:792 exit_to_usermode_loop+0x160/0x200 arch/x86/entry/common.c:160 prepare_exit_to_usermode arch/x86/entry/common.c:199 [inline] syscall_return_slowpath arch/x86/entry/common.c:270 [inline] do_syscall_64+0x4a3/0x640 arch/x86/entry/common.c:297 entry_SYSCALL_64_after_hwframe+0x46/0xbb RIP: 0033:0x466459 RSP: 002b:00007fe9dc788218 EFLAGS: 00000246 ORIG_RAX: 00000000000000ca RAX: fffffffffffffe00 RBX: 000000000056c160 RCX: 0000000000466459 RDX: 0000000000000000 RSI: 0000000000000080 RDI: 000000000056c160 RBP: 000000000056c158 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 000000000056c164 R13: 00007ffda371323f R14: 00007fe9dc788300 R15: 0000000000022000 batman_adv: batadv0: Interface deactivated: batadv_slave_0 batman_adv: batadv0: Removing interface: batadv_slave_0 batman_adv: batadv0: Interface deactivated: batadv_slave_1 batman_adv: batadv0: Removing interface: batadv_slave_1 device bridge_slave_1 left promiscuous mode bridge0: port 2(bridge_slave_1) entered disabled state device bridge_slave_0 left promiscuous mode bridge0: port 1(bridge_slave_0) entered disabled state device veth1_macvtap left promiscuous mode device veth0_macvtap left promiscuous mode device veth1_vlan left promiscuous mode device veth0_vlan left promiscuous mode device hsr_slave_1 left promiscuous mode device hsr_slave_0 left promiscuous mode team0 (unregistering): Port device team_slave_1 removed team0 (unregistering): Port device team_slave_0 removed bond0 (unregistering): Releasing backup interface bond_slave_1 bond0 (unregistering): Releasing backup interface bond_slave_0 bond0 (unregistering): Released all slaves IPVS: ftp: loaded support on port[0] = 21 chnl_net:caif_netlink_parms(): no params data found bridge0: port 1(bridge_slave_0) entered blocking state bridge0: port 1(bridge_slave_0) entered disabled state device bridge_slave_0 entered promiscuous mode bridge0: port 2(bridge_slave_1) entered blocking state bridge0: port 2(bridge_slave_1) entered disabled state device bridge_slave_1 entered promiscuous mode bond0: Enslaving bond_slave_0 as an active interface with an up link bond0: Enslaving bond_slave_1 as an active interface with an up link IPv6: ADDRCONF(NETDEV_UP): team_slave_0: link is not ready team0: Port device team_slave_0 added IPv6: ADDRCONF(NETDEV_UP): team_slave_1: link is not ready team0: Port device team_slave_1 added batman_adv: batadv0: Adding interface: batadv_slave_0 batman_adv: batadv0: The MTU of interface batadv_slave_0 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem. batman_adv: batadv0: Not using interface batadv_slave_0 (retrying later): interface not active batman_adv: batadv0: Adding interface: batadv_slave_1 batman_adv: batadv0: The MTU of interface batadv_slave_1 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1560 would solve the problem. batman_adv: batadv0: Not using interface batadv_slave_1 (retrying later): interface not active IPv6: ADDRCONF(NETDEV_UP): bridge_slave_0: link is not ready IPv6: ADDRCONF(NETDEV_UP): bridge_slave_1: link is not ready device hsr_slave_0 entered promiscuous mode device hsr_slave_1 entered promiscuous mode IPv6: ADDRCONF(NETDEV_UP): hsr_slave_0: link is not ready IPv6: ADDRCONF(NETDEV_UP): hsr_slave_1: link is not ready bridge0: port 2(bridge_slave_1) entered blocking state bridge0: port 2(bridge_slave_1) entered forwarding state bridge0: port 1(bridge_slave_0) entered blocking state bridge0: port 1(bridge_slave_0) entered forwarding state IPv6: ADDRCONF(NETDEV_UP): bond0: link is not ready 8021q: adding VLAN 0 to HW filter on device bond0 IPv6: ADDRCONF(NETDEV_UP): veth0: link is not ready IPv6: ADDRCONF(NETDEV_CHANGE): veth0: link becomes ready bridge0: port 1(bridge_slave_0) entered disabled state bridge0: port 2(bridge_slave_1) entered disabled state IPv6: ADDRCONF(NETDEV_UP): team0: link is not ready 8021q: adding VLAN 0 to HW filter on device team0 IPv6: ADDRCONF(NETDEV_CHANGE): bridge_slave_0: link becomes ready bridge0: port 1(bridge_slave_0) entered blocking state bridge0: port 1(bridge_slave_0) entered forwarding state IPv6: ADDRCONF(NETDEV_CHANGE): bridge_slave_1: link becomes ready bridge0: port 2(bridge_slave_1) entered blocking state bridge0: port 2(bridge_slave_1) entered forwarding state hsr0: Slave A (hsr_slave_0) is not up; please bring it up to get a fully working HSR network hsr0: Slave B (hsr_slave_1) is not up; please bring it up to get a fully working HSR network IPv6: ADDRCONF(NETDEV_UP): hsr0: link is not ready IPv6: ADDRCONF(NETDEV_CHANGE): team_slave_0: link becomes ready IPv6: ADDRCONF(NETDEV_CHANGE): team_slave_1: link becomes ready IPv6: ADDRCONF(NETDEV_CHANGE): hsr_slave_0: link becomes ready IPv6: ADDRCONF(NETDEV_CHANGE): hsr_slave_1: link becomes ready IPv6: ADDRCONF(NETDEV_CHANGE): hsr0: link becomes ready IPv6: ADDRCONF(NETDEV_CHANGE): team0: link becomes ready IPv6: ADDRCONF(NETDEV_UP): vxcan0: link is not ready IPv6: ADDRCONF(NETDEV_CHANGE): vxcan0: link becomes ready IPv6: ADDRCONF(NETDEV_CHANGE): vxcan1: link becomes ready 8021q: adding VLAN 0 to HW filter on device batadv0 IPv6: ADDRCONF(NETDEV_UP): veth0_virt_wifi: link is not ready IPv6: ADDRCONF(NETDEV_CHANGE): veth0_virt_wifi: link becomes ready IPv6: ADDRCONF(NETDEV_UP): veth0_vlan: link is not ready IPv6: ADDRCONF(NETDEV_UP): vlan0: link is not ready IPv6: ADDRCONF(NETDEV_UP): vlan1: link is not ready IPv6: ADDRCONF(NETDEV_CHANGE): veth0_vlan: link becomes ready IPv6: ADDRCONF(NETDEV_CHANGE): vlan0: link becomes ready IPv6: ADDRCONF(NETDEV_CHANGE): vlan1: link becomes ready device veth0_vlan entered promiscuous mode device veth1_vlan entered promiscuous mode IPv6: ADDRCONF(NETDEV_UP): macvlan0: link is not ready IPv6: ADDRCONF(NETDEV_UP): macvlan1: link is not ready IPv6: ADDRCONF(NETDEV_UP): veth0_macvtap: link is not ready IPv6: ADDRCONF(NETDEV_CHANGE): macvlan0: link becomes ready IPv6: ADDRCONF(NETDEV_CHANGE): macvlan1: link becomes ready IPv6: ADDRCONF(NETDEV_CHANGE): veth0_macvtap: link becomes ready device veth0_macvtap entered promiscuous mode IPv6: ADDRCONF(NETDEV_UP): macvtap0: link is not ready device veth1_macvtap entered promiscuous mode IPv6: ADDRCONF(NETDEV_UP): veth0_to_batadv: link is not ready IPv6: ADDRCONF(NETDEV_UP): veth1_to_batadv: link is not ready batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3d) already exists on: batadv_slave_0 batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems! batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3d) already exists on: batadv_slave_0 batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems! batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3d) already exists on: batadv_slave_0 batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems! batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3d) already exists on: batadv_slave_0 batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems! batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3d) already exists on: batadv_slave_0 batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems! batman_adv: batadv0: Interface activated: batadv_slave_0 IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready IPv6: ADDRCONF(NETDEV_CHANGE): veth0_to_batadv: link becomes ready IPv6: ADDRCONF(NETDEV_CHANGE): macvtap0: link becomes ready batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_1 batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems! batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_1 batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems! batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_1 batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems! batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_1 batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems! batman_adv: The newly added mac address (aa:aa:aa:aa:aa:3e) already exists on: batadv_slave_1 batman_adv: It is strongly recommended to keep mac addresses unique to avoid problems! IPv6: ADDRCONF(NETDEV_UP): batadv_slave_1: link is not ready batman_adv: batadv0: Interface activated: batadv_slave_1 IPv6: ADDRCONF(NETDEV_CHANGE): batadv_slave_1: link becomes ready IPv6: ADDRCONF(NETDEV_CHANGE): veth1_to_batadv: link becomes ready Bluetooth: hci0 command 0x0409 tx timeout Bluetooth: hci0 command 0x041b tx timeout